• continuous short circuit, over voltage protection
• temperature range (-40~85°C)
• six-sided metal shielding
• efficiency up to 88%
MODEL
typ
(Vdc)
input
voltage
range
(Vdc)
output
voltage
(Vdc)
min
(mA)
output
current
max
(mA)
output
power
max
(W)
ripple
and noise
1
max
(mVp-p)
efficiency
typ
(%)
PYB10-Q24-S3
PYB10-Q24-S5
PYB10-Q24-S12
PYB10-Q24-S15
PYB10-Q24-S24
PYB10-Q24-D5
PYB10-Q24-D12
PYB10-Q24-D15
PYB10-Q48-S3
PYB10-Q48-S5
PYB10-Q48-S12
PYB10-Q48-S15
PYB10-Q48-S24
PYB10-Q48-D5
PYB10-Q48-D12
PYB10-Q48-D15
Notes:
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
9~36
9~36
9~36
9~36
9~36
9~36
9~36
9~36
18~75
18~75
18~75
18~75
18~75
18~75
18~75
18~75
3.3
5
12
15
24
±5
±12
±15
3.3
5
12
15
24
±5
±12
±15
120
100
42
33
21
±50
±21
±16
120
100
42
33
21
±50
±21
±16
2400
2000
833
667
416
±1000
±416
±333
2400
2000
833
667
416
±1000
±416
±333
8
10
10
10
10
10
10
10
8
10
10
10
10
10
10
10
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
79
82
86
87
87
83
86
88
79
82
86
87
87
83
86
88
1. Ripple and noise are measured at 20 MHz BW by “parallel cable” method
PART NUMBER KEY
PYB10 - QXX -
XXX
-
X
Base Number
Input Voltage
Output Voltage
Output
S = single
D = dual
CTRL Pin
"blank" = on/off control
A = no on/off control
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
PYB10
│
DESCRIPTION:
DC-DC CONVERTER
date
08/15/2013
│
page
2 of 6
INPUT
parameter
operating input voltage
start-up voltage
surge voltage
fi
lter
CTRL
1
Note:
conditions/description
24 V input models
48 V input models
24 V input models
48 V input models
for maximum of 1 second
24 V input models
48 V input models
pi
fi
lter
min
9
18
typ
24
48
max
36
75
9
18
units
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
-0.7
-0.7
50
100
models ON (CTRL open or connect high level, 3.5-12 Vdc)
models OFF (CTRL connect GND or low level, 0-1.2 Vdc)
input current (models OFF)
1. CTRL pin voltage is referenced to GND.
1
3
mA
OUTPUT
parameter
line regulation
load regulation
cross regulation
voltage accuracy
voltage balance
2
switching frequency
transient recovery time
transient response deviation
temperature coefficient
Note:
conditions/description
full load, input voltage from low to high
5% to 100% load
dual output models:
main output 50% load, secondary output from
10% to 100% load
min
typ
±0.2
±0.5
max
±0.5
±1
±5
units
%
%
%
%
%
KHz
μs
%
%/°C
±1
dual output, balanced loads
PWM mode
25% load step change
25% load step change
100% load
±0.5
350
300
±3
±2
±1.5
500
±5
±0.03
2. For dual output models, unbalanced load can not exceed ±5%. If ±5% is exceeded, it may not meet all specifications.
PROTECTIONS
parameter
short circuit protection
over voltage protection
conditions/description
continuous, automatic recovery
110
120
140
%Vo
min
typ
max
units
SAFETY AND COMPLIANCE
parameter
isolation voltage
isolation resistance
conducted emissions
radiated emissions
ESD
radiated immunity
EFT/burst
surge
conducted immunity
voltage dips & interruptions
MTBF
RoHS compliant
conditions/description
for 1 minute at 1 mA max.
at 500 Vdc
min
1,500
1,000
typ
max
units
Vdc
MΩ
CISPR22/EN55022, class A, class B (external circuit required, see Figure 1-b)
CISPR22/EN55022, class A, class B (external circuit required, see Figure 1-b)
IEC/EN61000-4-2, class B, contact ± 4kV
IEC/EN61000-4-3, class A, 10V/m
IEC/EN61000-4-4, class B, ± 2kV (external circuit required, see Figure 1-a)
IEC/EN61000-4-5, class B, ± 2kV (external circuit required, see Figure 1-a)
IEC/EN61000-4-6, class A, 3 Vr.m.s
IEC/EN61000-4-29, class B, 0%-70%
as per MIL-HDBK-217F @ 25°C
yes
1,000,000
hours
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
PYB10
│
DESCRIPTION:
DC-DC CONVERTER
date
08/15/2013
│
page
3 of 6
ENVIRONMENTAL
parameter
operating temperature
storage temperature
storage humidity
case temperature
vibration
non-condensing
at full load, Ta=71°C
10~55 Hz for 30 min. along X, Y and Z axis
10
conditions/description
see derating curve
min
-40
-55
5
typ
max
85
125
95
105
units
°C
°C
%
°C
G
SOLDERABILITY
parameter
hand soldering
wave soldering
conditions/description
1.5 mm from case for 10 seconds
see wave soldering profile
min
typ
max
300
260
units
°C
°C
MECHANICAL
parameter
dimensions
case material
weight
conditions/description
50.8 x 25.4 x 11.8
aluminum alloy
22
g
min
typ
max
units
mm
MECHANICAL DRAWING
units: mm[inch]
tolerance: ±0.3[±0.012]
pin diameter tolerance: ±0.10[±0.004]
pin height tolerance: ±0.50[±0.020]
PIN CONNECTIONS
PIN
1
2
3
4
5
6*
Note:
Single
Output
GND
Vin
+Vo
No Pin
0V
CTRL
Dual
Output
GND
Vin
+Vo
0V
-Vo
CTRL
Grid Size: 2.54mm x 2.54mm
Front View
6
3
1
2
1
6
4
2
3
4
5
* "No Pin" option available.
5
Bottom View
PCB Layout
Top View
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
PYB10
│
DESCRIPTION:
DC-DC CONVERTER
date
08/15/2013
│
page
4 of 6
DERATING CURVES
Wave Soldering Profile
Peak Temp. 260°C Max.
250
Wave Soldering Time
4 Sec. Max.
Temperature Derating Curve
100
80
60
200
Temperature (°C)
10 Sec. Max.
150
Load (%)
Safe operating area
40
20
100
50
0
Time (sec.)
-40
-20
0
20
40
60 71
85
Ambient Temperature (°C)
EMC RECOMMENDED CIRCUIT
FUSE
V in
LDM1
+
MOV
GND
(a)
(b)
CY2
LDM2
C1
Vin
+Vo
Figure 1
TVS
C0
EUT
GND
CY1
LOAD
-Vo
(0V)
Table 1
Recommended external circuit components
Vin (Vdc)
FUSE
MOV
LDM1
TVS
C0
C1
LDM2
CY1
CY2
24
S14K35
56μH
SMCJ48A
330μF/50V
1μF/50V
4.7μH
1 nF/2 KV
1 nF/2 KV
48
S14K60
56μH
SMCJ90A
330μF/100V
1μF/100V
4.7μH
1 nF/2 KV
1 n/2 KV
Choose according to input current
TEST CONFIGURATION
Oscilloscope
Lin
Figure 2
Lin
Table 2
External components
4.7μH
220μF, ESR < 1.0Ω
at 100 KHz
Cin
Current
Probe
DC DC
Load
Cin
Note:
Input reflected-ripple current is measured with an inductor Lin and Capacitor Cin to simulate source impedance.
cui.com
For more information, please visit the
product page.
CUI Inc
│
SERIES:
PYB10
│
DESCRIPTION:
DC-DC CONVERTER
date
08/15/2013
│
page
5 of 6
APPLICATION NOTES
1.
Recommended circuit
This series has been tested according to the following recommended testing circuit before leaving the factory. This series should be
tested under load (see Figure 3). If you want to further decrease the input/output ripple, you can increase the capacitance accord-
ingly or choose capacitors with low ESR (see table 3). However, the capacitance of the output
fi
lter capacitor must be appropriate. If
the capacitance is too high, a startup problem might arise. For every channel of the output, to ensure safe and reliable operation, the
maximum capacitance must be less than the maximum capacitive load (see Table 4).
Figure 3
Single Output
Vin
Cin
Dual O utput
+Vo
Vin
Cin
+Vo
C out
DC DC
C out
DC DC
GND
0V
GND
Cout
0V
-Vo
Table 3
Vin
(Vdc)
24
48
Cin
(μF)
10~47
10~47
Cout
(μF)
10
10
Single
Vout
(Vdc)
3.3
5
12
15
24
Notes:
1.
2.
3.
4.
Table 4
Max.
Capacitive
Load
(μF)
2200
2200
470
1
330
2
100
330
μF
for 48Vin.
220
μF
for 48Vin.
150
μF
for 48Vin.
For each output.
Dual
Vout
(Vdc)
--
5
12
15
--
Max.
Capacitive
Load
4
(μF)
--
680
220
3
100
--
Note:
1. Minimum load shouldn't be less than 5%, otherwise ripple may increase dramatically. Operation under minimum load will not damage the converter, however, they may
not meet all specifications listed.
2. Maximum capacitive load is tested at input voltage range and full load.
3. All specifications are measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
According to foreign media reports, employees of Foxconn, a Chinese factory that produces iPhones and iPads for Apple, were forced to sign a no-suicide agreement. It is reported that Foxconn asked emp...
I want to design a gas alarm system but feel a bit overwhelmed. I would like to ask experts for some advice. Thank you very much!
This is the system block diagram I designed
Sensor → Amplifier → A/D C...
In a WINCE+ARM system, what effect does adding a const modifier to a global, immutable array have? Reduce memory usage? Increase program execution speed? Can ROM be used as RAM in ARM?...
[size=14px] To date, almost all FPC manufacturing processes have been processed using the subtractive method (etching method). According to Carbon Technology, copper-clad laminate is usually used as t...
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
Images in science fiction movies often break through the limits of reality, such as in the movie "Minority Report." Tom Cruise uses a multi-touch screen to browse information. Capacitive sensing te...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
Xiaomi, a well-known Internet phone in mainland China, won a million-unit order contract from China Unicom on November 20 last year, which made Xiaomi famous in mainland China. In April this year...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
This paper designs a 16x16LED Chinese character display bar based on single-chip dynamic scanning control, briefly analyzes the principle of Chinese character display, and studies how the LED displ...[Details]
At present, a large number of cooling tower fans, speed fans and special fans are in use in petroleum, chemical, pharmaceutical, metallurgical and other enterprises. Some fans have no monitoring in...[Details]
Almost everyone in a student dormitory has a bedside lamp. But if you want to read for a while after turning off the lights and don't want to disturb your roommates' sleep, you may need a reading l...[Details]
The fluorescent lamps and energy-saving lamps we commonly use now have greatly improved luminous efficiency compared with the earlier ordinary incandescent lamps and have been widely used. With the...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems (GP...[Details]
introduction
When it comes to the production of mobile phone lithium-ion batteries, the first thing that comes to mind is Japan's industrialized mechanical assembly line, NOKIO, MOTOLROLA's st...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
