51700-10303203ACLF datasheet, PDF

Datasheet> All Categories > The connector> 51700-10303203ACLF

51700-10303203ACLF: DescriptionPower to the Board 51700-10303203ACLF-PWRBLADE V/T HDR; CategoryThe connector; File Size91KB，13 Pages; ManufacturerFCI [First Components International]

Download Datasheet Parametric View All

51700-10303203ACLF Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	51700-10303203ACLF	-	-	View	Buy Now

51700-10303203ACLF Overview

Power to the Board 51700-10303203ACLF-PWRBLADE V/T HDR

51700-10303203ACLF Parametric

Parameter Name	Attribute value
Product Category	Power to the Board
Manufacturer	FCI [First Components International]
RoHS	Details
Packaging	Tray
Factory Pack Quantity	33

Preview

Download Datasheet

View All

NUMBER

TYPE

GS-12-149

TITLE

PRODUCT SPECIFICATION

PAGE

REVISION

PwrBlade

Product Specification

1 of 13

AUTHORIZED BY

DATE

29 Jul 16

MT Ruan

CLASSIFICATION

UNRESTRICTED

1.0

OBJECTIVE

This specification defines the performance, test, quality and reliability requirements of the PwrBlade

Connector System.

2.0

SCOPE

This specification is applicable to the termination characteristics of separable right angle and vertical headers

when mated to the right angle and vertical receptacles.

3.0

GENERAL

If there is conflict between the product drawings and specifications, the drawing takes precedence.

This document is composed of the following sections:

Paragraph

1.0

2.0

3.0

4.0

5.0

5.1

5.2

5.3

5.4

5.5

6.0

7.0

8.0

9.0

9.1

9.2

9.3

9.4

9.5

9.6

10.0

Table 2

Title

OBJECTIVE

SCOPE

GENERAL

APPLICABLE DOCUMENTS

REQUIREMENTS

Qualification

Material

Finish

Design and construction

Workmanship

ELECTRICAL CHARACTERISTICS

MECHANICAL CHARACTERISTICS

ENVIRONMENTAL CONDITIONS

QUALITY ASSURANCE PROVISIONS

Equipment Calibration

Inspection Conditions

Sample Quality and Description

Acceptance

Qualification Testing

Re-qualification Testing

Reference Documents

Qualification Testing Matrix

Form E-3334

Rev F

PDS: Rev :AA

GS-01-001

STATUS:Released

Printed: Jul 29, 2016

NUMBER

TYPE

GS-12-149

TITLE

PRODUCT SPECIFICATION

PAGE

REVISION

PwrBlade

Product Specification

5 of 13

AUTHORIZED BY

DATE

29 Jul 16

MT Ruan

CLASSIFICATION

UNRESTRICTED

7.3

Contact Retention – Individual power and signal contacts shall withstand an axial retention load of

13.4N [3 pound]. Individual signal receptacle contacts will withstand an axial load of 26.7N [6 pound]

minimum to seat further into housing.

a. Rate of 12.7mm [0.5 inch] per minute without dislodging from the housing cavity.

b. Test 30 contacts

c. As per MIL-STD-1344A, Method 2007.1.

7.4

Individual Pin Insertion/Retention Force - The force required to insert an individual compliant pin into

a plated through hole in a printed circuit board at a rate of 5.08mm [0.2 inch] per minute shall not

exceed 26.6N [6 pound] for signal receptacle contacts, 93.4N [21 pound] for signal header pins and

111.2N [25 pound] per tail for power contacts . The retention force in the axial direction opposite that

of insertion shall not be less than 6.7N [1.5 pound] for signal receptacle contacts, 13.4N [3 pound] for

signal header pins and 22.3N [5 pound] per tail for power contacts.

Table 3: Individual Pin Insertion/Retention Force table

Pwr contact

(per tail)

111.2N [25lbs]

22.3N [5lbs]

Signal contact

Rec Signal contact

26.6N [6lbs]

6.7N [1.5lbs]

Hdr Signal contact

93.4N [21lbs]

13.4N [3lbs]

Force spec.

Insertion force Maximum

Retention force Minimum

7.5

PCB Hole Deformation Radius

Power Contacts – cross-section parallel to board surface. Photograph and measure the hole

deformation (deformation on board material) radius at a point 0.254mm [0.010”] from the surface, and

the center of the compliant pin section. Include 10 holes. The average (of 10 holes) hole deformation

radius shall be no greater than0.0381mm [0.0015”] when measured from the drilled hole. The

absolute maximum deformation radius shall not exceed 0.0508mm [0.002”].

Signal Contacts

Signal Receptacle Contacts – Reference FCI BUS-12-111 – HPC Solderless (Press Fit) Right Angle

Receptacles

Signal Header Contacts – Same as the requirement for Power Contacts above

7.6

PCB Hole Wall Damage – Cross-section perpendicular to the board surface, and through the

compliant section wear track. Photograph and measure the copper thickness remaining between the

compliant section and the printed wiring board laminate. Include 10 holes. The minimum average (of

10 holes) copper thickness remaining between the compliant pin and the printed wiring board

laminate shall not be less than 0.00762mm [0.0003”]. In addition there shall be no copper cracks,

separations between conductive interfaces, or laminate-to-copper separations.

Form E-3334

Rev F

PDS: Rev :AA

GS-01-001

STATUS:Released

Printed: Jul 29, 2016

Recommended Resources

Toy walkie-talkie circuit

24% bandwidth audio decoder circuit diagram

Modified circuit diagram of transistor regulated power supply

Non-coding touch keyboard composed of CMOS circuit

Mains photoelectric control circuit

Electronic time relay circuit

CC3200 TCP Programming: [align=left][color=#000]我遇到一个问题，想请教你一下， [/color][/align][color=#000][size=1em][font=Consolas,][align=center][color=#cd171f][size=1em][url=http://www.deyisupport.com/question_answer/wireless_connectivi...; dongjie_0000 Wireless Connectivity

[TI's first low power design competition] Copter_alarm_powered_by_MSP430FR5969 VII - Download and debug: [align=left]Download and debug[/align] [align=left]The minimum system welding is completed, and the experiment can be burned and debugged[/align][align=left]Thanks to the friends in the QQ group for t...; tziang Microcontroller MCU

After successfully acquiring Luminary, TI made its first big move~~: The industry leader is the industry leader. After acquiring Luminary in May this year, TI launched 31 MCUs today, including 29 Stellaris Cortex-M3 MCUs and MPUs based on ARM9 and Cortex-A8 technologie...; clark Microcontroller MCU

About the installation and errors of IAR for msp430 under WIN8!: [backcolor=white]Thanks for the summary of [color=#333333][size=12px]delay_year[/size][/color], those who are trying to use Windows 8 can give it a try. [/backcolor] [size=4]1. In fact, the installati...; wstt Microcontroller MCU

Correct method for detecting varistor: [p=30, null, left][font=宋体][size=4][color=#000000] When testing a varistor, the resistance range switch of the multimeter should be set to the highest level. The resistance of the two pins of the vari...; fish001 Analogue and Mixed Signal

Socket buffer problem: I have recently done a project migration from vc to wince. After the program was migrated to wince, it can run normally on the windows mobile 5.0 simulator, but there is a problem when it is run on th...; LPcfANS Embedded System

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components