SMD POWER RESISTORS
Type 3522 Series
Key Features
3 Watts at
70°C
Small size to
power ratio
Supplied on
tape
Value marked
on resistor
Available via
distribution
500 volt
maximum
overload
250 volt
working
voltage
Terminal finish
matte Sn over
Ni
TE Connectivity is pleased to introduce this low cost high power device, suitable
for auto placement in volume and for most applications, including high
frequency operations, owing to the short lead structure. Supplied as standard
on 7 inch Reels of 2000 pieces per reel.
Characteristics – Electrical
Power rating at 70°C
Rated current (Jumper)
Max. overload current (Jumper)
Max working voltage
Max overload voltage
Dielectric withstand voltage
Temperature range
Ambient temperature
3W
2.5A
10A
250V
500V
500V
-55°C ~ +155°C
70°C
* Rated continuous working voltage (RCWV) shall be determined from
RCWV = Rated Power x Resistance Value, or Maximum RCWV listed above,
whichever is less
**Recommended Circuit Board Design - If this device is anticipated to run at full
continuous power then action to improve the cooling should be taken. This can
be a metal substrate, copper pad left under the chip, an opening in the PCB or
enlarged silver conductor pads each end.
9-1773463-7 CIS WR 10/2015
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
SMD POWER RESISTORS
Power derating curve
For resistors operated in ambient temperatures above 70°C, power rating
must be derated in accordance with this curve.
Construction and dimensions
L ± 0.10
6.35
Power rating
@70°C
3W
W ± 0.15
3.20
H ± 0.10
1.10
ℓ1 ± 0.25
0.60
ℓ2 ± 0.20
1.80
Standard series
Tolerance %
Jumper
± 1%
± 5%
Resistance
Range
<50mΩ
10Ω - 1MΩ
10Ω - 10MΩ
E96
E24
9-1773463-7 CIS WR 10/2015
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
SMD POWER RESISTORS
Marking:
Marking for E-96 series in 2512 size: 4 digit marking
First three digits are significant figures of resistance and the fourth
digit represents the number of following zeros
Marking for E-24 series in 2512 size: 3 digit marking
First two digits are significant figures, and the third digit represents
the number of zeros
Packing specification:
Taping dimensions (mm)
A
B
C
ØD
±0.20 ±0.20 ±0.05 +0.1
-0
3.5
6.7
2.0
1.5
Peeling strength of Top Cover Tape
E
F
G
W
ØD1
±0.10 ±0.05 ±0.1 ±0.20 +0.1
-0
1.75 5.5
4.0 12
1.5
T
±0.1
1.35
Test Condition 0.1 to 0.7 N at a peel-off speed of 300mm / min.
9-1773463-7 CIS WR 10/2015
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
SMD POWER RESISTORS
Reel dimension (mm)
Qty / Reel
2000
A ±0.5
2
B ±0.5
13.5
C ±0.5
21
D ±1
60
M ±2
178
W ±1
13.8
Handling Recommendations
When flow soldering - the land width must be smaller than the Chip Resistor
width to properly control the solder application. Generally, the land width
can be Chip Resistor width (W) x 0.7 to 0.8. When reflow soldering – solder
application amount can be adjusted. Thus the land width can be set to W x
1.0 to 1.3.
How To Order
3522
1K0
F
T
Common Part
Resistance Value
1 ohm 1R0
1K ohm 1000 ohms
1K0
1 Meg ohm
1000000 ohms
1M0
Tolerance Pack Style
3522
F – 1%
J – 5%
T – 2000
reel
9-1773463-7 CIS WR 10/2015
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
京公网安备 11010802033920号
EEWORLD
