MCZ145010EGR2 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> The signal circuit> MCZ145010EGR2

MCZ145010EGR2: DescriptionSmoke Detectors SMOKE DET.PHOTO; CategoryAnalog mixed-signal IC The signal circuit; File Size429KB，12 Pages; ManufacturerNXP; Websitehttps://www.nxp.com; Environmental Compliance

Download Datasheet Parametric Compare View All

MCZ145010EGR2 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	MCZ145010EGR2	-	-	View	Buy Now

MCZ145010EGR2 Overview

Smoke Detectors SMOKE DET.PHOTO

MCZ145010EGR2 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	NXP
Parts packaging code	SOIC
package instruction	LEAD FREE, SOIC-16
Contacts	16
Reach Compliance Code	unknown
ECCN code	EAR99
Analog Integrated Circuits - Other Types	ANALOG CIRCUIT
JESD-30 code	R-PDSO-G16
JESD-609 code	e3
length	10.3 mm
Humidity sensitivity level	3
Number of functions	1
Number of terminals	16
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package body material	PLASTIC/EPOXY
encapsulated code	SOP
Encapsulate equivalent code	SOP16,.4
Package shape	RECTANGULAR
Package form	SMALL OUTLINE
Peak Reflow Temperature (Celsius)	260
power supply	6/12 V
Certification status	Not Qualified
Maximum seat height	2.65 mm
Maximum supply voltage (Vsup)	12 V
Minimum supply voltage (Vsup)	6 V
Nominal supply voltage (Vsup)	9 V
surface mount	YES
technology	CMOS
Temperature level	MILITARY
Terminal surface	Matte Tin (Sn)
Terminal form	GULL WING
Terminal pitch	1.27 mm
Terminal location	DUAL
Maximum time at peak reflow temperature	40
width	7.5 mm

Preview

Download Datasheet

View All

Freescale Semiconductor

Technical Data

MC145010

Rev 7.0, 05/2006

Photoelectric Smoke

Detector IC with I/O

The CMOS MC145010 is an advanced smoke detector component containing

sophisticated very-low-power analog and digital circuitry. The IC is used with an

infrared photoelectric chamber. Detection is accomplished by sensing scattered

light from minute smoke particles or other aerosols. When detection occurs, a

pulsating alarm is sounded via on-chip push-pull drivers and an external

piezoelectric transducer.

The variable-gain photo amplifier allows direct interface to IR detectors

(photodiodes). Two external capacitors, C1 and C2, C1 being the larger, determine

the gain settings. Low gain is selected by the IC during most of the standby state.

Medium gain is selected during a local-smoke condition. High gain is used during

push button test. During standby, the special monitor circuit which periodically

checks for degraded chamber sensitivity uses high gain, also.

The I/O pin, in combination with V

, can be used to interconnect up to 40 units

for common signaling. An on-chip current sink provides noise immunity when the I/

O is an input. A local-smoke condition activates the short-circuit-protected I/O

driver, thereby signaling remote smoke to the interconnected units. Additionally, the

I/O pin can be used to activate escape lights, enable auxiliary or remote alarms,

and/or initiate auto-dialers.

While in standby, the low-supply detection circuitry conducts periodic checks

using a pulsed load current from the LED pin. The trip point is set using two external

resistors. The supply for the MC145010 can be a 9 V battery.

A visible LED flash accompanying a pulsating audible alarm indicates a local-

smoke condition. A pulsating audible alarm with no LED flash indicates a remote-

smoke condition. A beep or chirp occurring virtually simultaneously with an LED

flash indicates a low-supply condition. A beep occurring half-way between LED

flashes indicates degraded chamber sensitivity. A low-supply condition does not

affect the smoke detection capability if V

≥

6 V. Therefore, the low-supply

condition and degraded chamber sensitivity can be further distinguished by

performing a push button (chamber) test.

Features

•

Circuit is designed to operate in smoke detector systems that comply with

UL217 and UL268 Specifications

Operating Voltage Range: 6 to 12 V

Operating Temperature Range: - 10 to 60°C

Average Supply Current: 12

µA

Power-On Reset Places IC in Standby Mode (Non-Alarm State)

Electrostatic Discharge (ESD) and Latch Up Protection Circuitry on All Pins

Chip Complexity: 2000 FETs, 12 NPNs, 16 Resistors, and 10 Capacitors

Ideal for battery powered applications.

ORDERING INFORMATION

Device

MC145010P

MC145010ED

MC145010DW

MCZ145010EG/EGR2

-55 to +125°C

751G-04

16 Lead SOICW

Temp. Range

Case No.

648-08

Package

16 Lead Plastic Dip

MC145010

PHOTOELECTRIC SMOKE

DETECTOR IC WITH I/O

P SUFFIX

ED SUFFIX (PB-FREE)

PLASTIC DIP

CASE 648-08

DW SUFFIX

EG SUFFIX (PB-FREE)

SOICW

CASE 751G-04

Detect

Strobe

IRED

I/O

Brass

Test

Low-Supply

Trip

OSC

LED

Feedback

Silver

Figure 1. Pin Connections

Table 4. Pin Description

Symbol

Description

A capacitor connected to this pin, shown in

Figure 8,

determines the gain of the on-chip photo amplifier during push button

test and chamber sensitivity test (high gain). The capacitor value is chosen such that the alarm is tripped from background

reflections in the chamber during push button test.

ª 1 + (C1/10) where C1 is in pF. CAUTION: The value of the closed-loop gain should not exceed 10,000.

A capacitor connected to this pin as shown in

Figure 8

determines the gain of the on-chip photo amplifier except during

push button or chamber sensitivity tests. A

≈

1 + (C2/10) where C2 is in pF. This gain increases about 10% during the

IRED pulse, after two consecutive local smoke detections.

Resistor R14 must be installed in series with C2. R14

≈

[1/(12√C2)] - 680 where R14 is in ohms and C2 is in farads.

DETECT This input to the high-gain pulse amplifier is tied to the cathode of an external photodiodes. The photodiodes should have

low capacitance and low dark leakage current. The diode must be shunted by a load resistor and is operated at zero bias.

The Detect input must be ac/dc decoupled from all other signals, V

, and V

. Lead length and/or foil traces to this pin

must be minimized, also. See

Figure 9.

STROBE This output provides a strobed, regulated voltage referenced to V

. The temperature coefficient of this voltage is

0.2%/

°C

maximum from - 10° to 60°C. The supply-voltage coefficient (line regulation) is

0.2%/V maximum from 6 to 12 V.

Strobe is tied to external resistor string R8, R9, and R10.

IRED

This pin is connected to the positive supply potential and may range from +6 to +12 V with respect to V

. CAUTION: In

battery-powered applications, reverse-polarity protection must be provided externally.

This output provides pulsed base current for external NPN transistor Q1 used as the infrared emitter driver. Q1 must have

β ≥

100. At 10 mA, the temperature coefficient of the output voltage is typically + 0.5%/°C from - 10° to 60°C. The supply-

voltage coefficient (line regulation) is

0.2%/V maximum from 6 to 12 V. The IRED pulse width (active-high) is determined

by external components R1 and C3. With a 100 kΩ/1500 pF combination, the nominal width is 105

µs.

To minimize noise

impact, IRED is not active when the visible LED and horn outputs are active. IRED is active near the end of Strobe pulses

for Smoke Tests, Chamber Sensitivity Test, and Push button Test.

This pin can be used to connect up to 40 units together in a wired-OR configuration for common signaling. V

is used as

the return. An on-chip current sink minimizes noise pick up during non-smoke conditions and eliminates the need for an

external pull-down resistor to complete the wired-OR. Remote units at lower supply voltages do not draw excessive current

from a sending unit at a higher supply voltage.

I/O can also be used to activate escape lights, auxiliary alarms, remote alarms, and/or auto-dialers.

As an input, this pin feeds a positive-edge-triggered flip-flop whose output is sampled nominally every 625 ms during

standby (using the recommended component values). A local-smoke condition or the push button-test mode forces this

current-limited output to source current. All input signals are ignored when I/O is sourcing current. I/O is disabled by the

on-chip power-on reset to eliminate nuisance signaling during battery changes or system power-up. If unused, I/O must

be left unconnected.

This half of the push-pull driver output is connected to the metal support electrode of a piezoelectric audio transducer and

to the horn-starting resistor. A continuous modulated tone from the transducer is a smoke alarm indicating either local or

remote smoke. A short beep or chirp is a trouble alarm indicating a low supply or degraded chamber sensitivity.

This half of the push-pull driver output is connected to the ceramic electrode of a piezoelectric transducer and to the horn-

starting capacitor.

I/O

BRASS

SILVER

FEEDBA This input is connected to both the feedback electrode of a self-resonating piezoelectric transducer and the horn-starting

resistor and capacitor through current-limiting resistor R4. If unused, this pin must be tied to V

or V

LED

This active-low open-drain output directly drives an external visible LED at the pulse rates indicated below. The pulse width

is equal to the OSC period.

The load for the low-supply test is applied by this output. This low-supply test is non-coincident with the smoke tests,

chamber sensitivity test, push button test, or any alarm signals.

The LED also provides a visual indication of the detector status as follows, assuming the component values shown in

Figure 8:

Standby (includes low-supply and chamber sensitivity tests) - Pulses every 43 seconds (nominal) Local Smoke

- Pulses every 0.67 seconds (nominal) Remote Smoke - No pulses

Push button Test - Pulses every 0.67 seconds (nominal)

This pin is used in conjunction with external resistor R2 (10 MΩ) to V

and external capacitor C3 (1500 pF) to V

form an oscillator with a nominal period of 10.5 ms.

This pin is used in conjunction with resistor R1 (100 kΩ) to pin 12 and C3 (1500 pF, see pin 12 description) to determine

the IRED pulse width. With this RC combination, the nominal pulse width is 105

µs.

This pin is the negative supply potential and the return for the I/O pin. Pin 14 is usually tied to ground.

OSC

VSS

LOW-

This pin is connected to an external voltage which determines the low-supply alarm threshold. The trip voltage is obtained

SUPPLY through a resistor divider connected between the V

and LED pins. The low-supply alarm threshold voltage (in volts)

≈

TRIP

(5R7/R6) + 5 where R6 and R7 are in the same units.

MC145010

Sensors

Freescale Semiconductor

MCZ145010EGR2 Related Products

	MCZ145010EGR2	MCZ145010EG	MC145010ED	MC145010DW	MC145010P
Description	Smoke Detectors SMOKE DET.PHOTO	Smoke Detectors PHOTO SMKE DET/NFPA TONE		IC SMOKE DETECT WITH I/O 16SOIC	IC SMOKE DETECT PHOTOELEC 16-DIP
Is it Rohs certified?	conform to	conform to	conform to	incompatible	conform to
Maker	NXP	NXP	NXP	NXP	NXP
Parts packaging code	SOIC	SOIC	DIP	SOIC	DIP
package instruction	LEAD FREE, SOIC-16	LEAD FREE, SOIC-16	DIP, DIP16,.3	SOP, SOP16,.4	DIP, DIP16,.3
Contacts	16	16	16	16	16
Reach Compliance Code	unknown	unknown	unknown	not_compliant	unknown
ECCN code	EAR99	EAR99	EAR99	EAR99	EAR99
Analog Integrated Circuits - Other Types	ANALOG CIRCUIT	ANALOG CIRCUIT	ANALOG CIRCUIT	ANALOG CIRCUIT	ANALOG CIRCUIT
JESD-30 code	R-PDSO-G16	R-PDSO-G16	R-PDIP-T16	R-PDSO-G16	R-PDIP-T16
JESD-609 code	e3	e3	e3	e0	e3
length	10.3 mm	10.3 mm	19.175 mm	10.3 mm	19.175 mm
Number of functions	1	1	1	1	1
Number of terminals	16	16	16	16	16
Maximum operating temperature	125 °C	125 °C	125 °C	125 °C	125 °C
Minimum operating temperature	-55 °C	-55 °C	-55 °C	-55 °C	-55 °C
Package body material	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY
encapsulated code	SOP	SOP	DIP	SOP	DIP
Encapsulate equivalent code	SOP16,.4	SOP16,.4	DIP16,.3	SOP16,.4	DIP16,.3
Package shape	RECTANGULAR	RECTANGULAR	RECTANGULAR	RECTANGULAR	RECTANGULAR
Package form	SMALL OUTLINE	SMALL OUTLINE	IN-LINE	SMALL OUTLINE	IN-LINE
Peak Reflow Temperature (Celsius)	260	260	220	245	NOT SPECIFIED
power supply	6/12 V	6/12 V	6/12 V	9 V	9 V
Certification status	Not Qualified	Not Qualified	Not Qualified	Not Qualified	Not Qualified
Maximum seat height	2.65 mm	2.65 mm	4.44 mm	2.65 mm	4.44 mm
Maximum supply voltage (Vsup)	12 V	12 V	12 V	12 V	12 V
Minimum supply voltage (Vsup)	6 V	6 V	6 V	6 V	6 V
Nominal supply voltage (Vsup)	9 V	9 V	9 V	9 V	9 V
surface mount	YES	YES	NO	YES	NO
technology	CMOS	CMOS	CMOS	CMOS	CMOS
Temperature level	MILITARY	MILITARY	MILITARY	MILITARY	MILITARY
Terminal surface	Matte Tin (Sn)	Matte Tin (Sn)	Matte Tin (Sn)	Tin/Lead (Sn/Pb)	Matte Tin (Sn)
Terminal form	GULL WING	GULL WING	THROUGH-HOLE	GULL WING	THROUGH-HOLE
Terminal pitch	1.27 mm	1.27 mm	2.54 mm	1.27 mm	2.54 mm
Terminal location	DUAL	DUAL	DUAL	DUAL	DUAL
Maximum time at peak reflow temperature	40	40	30	30	NOT SPECIFIED
width	7.5 mm	7.5 mm	7.62 mm	7.5 mm	7.62 mm
Humidity sensitivity level	3	3	-	1	-

Recommended Resources

FET power amplifier with output transformer 01

555 bus stop indicator circuit diagram

Power supply circuit with current limit and adjustable voltage

High-precision high-voltage regulated power supply circuit

DG type electric heating constant temperature drying oven circuit 01

Jinniu charger circuit

STC_ISP_V480 MCU burning who can give me a download address: STC_ISP_V480 microcontroller burning who can give me a download address, thank you...; ylf175300 51mcu

Design of push-pull boost switching power supply based on TI chip UCC2808 (transferred): [p=24, null, left][color=rgb(0, 0, 0)][font=Arial, Helvetica, sans-serif]1 The push-pull converter is one of the earliest and most widely used topologies. [/font][/color][/p][p=24, null, left][color=r...; qwqwqw2088 Analogue and Mixed Signal

Ask for help from VHDL and CPLD experts: I want to write an 8-port serial program with VDHL, requiring interrupt sharing and non-reuse of addresses. It is connected to CPLD. Thank you for your help!...; crab0918 Embedded System

How to decode the text messages received in CDMA Mode into the correct content.: Today I took a WAVECOM CDMA Modem to test it. I sent "China Telecom" with my mobile phone, and then used AT+CMGR=1 to receive the text message, but the message displayed was "NV齯5O?". How can I decode...; shxhzxll Embedded System

Do you want to use your time after get off work to learn something?: [size=4]Please enlighten me and tell me the pros and cons of doing or not doing something. [/size][size=4]I have been troubled recently, and I have been thinking about whether I should learn other thi...; yijindz Talking about work

The development prospects of the latest bus technology in instrument control and connection applications: [table][tr][td=1,1,920][b]Introduction[/b][/td][/tr][/table][b]Introduction[/b] For more than two decades, scientists and engineers have used IEEE 488 and the general purpose interface bus (GPIB) exte...; cscl Test/Measurement

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components