38.88MHZCFPT-9058HC2C datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 38.88MHZCFPT-9058HC2C

38.88MHZCFPT-9058HC2C: DescriptionHCMOS Output Clock Oscillator, 38.88MHz Nom, SMD, 6 PIN; CategoryPassive components oscillator; File Size62KB，4 Pages; ManufacturerC-MAC Automotive; Websitehttps://cmac.com

Download Datasheet Parametric View All

38.88MHZCFPT-9058HC2C Overview

HCMOS Output Clock Oscillator, 38.88MHz Nom, SMD, 6 PIN

38.88MHZCFPT-9058HC2C Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	incompatible
Maker	C-MAC Automotive
Reach Compliance Code	unknown
Other features	TRI-STATE; ENABLE/DISABLE FUNCTION
Ageing	1 PPM/FIRST YEAR
Maximum control voltage	2.65 V
Minimum control voltage	0.65 V
maximum descent time	8 ns
Frequency Adjustment - Mechanical	NO
frequency stability	2.5%
Manufacturer's serial number	CFPT-9058
Installation features	SURFACE MOUNT
Nominal operating frequency	38.88 MHz
Maximum operating temperature	70 °C
Minimum operating temperature
Oscillator type	HCMOS
Output load	15 pF
physical size	14.7mm x 9.2mm x 6.2mm
longest rise time	8 ns
Maximum supply voltage	3.63 V
Minimum supply voltage	2.97 V
Nominal supply voltage	3.3 V
surface mount	YES
maximum symmetry	45/55 %
Base Number Matches	1

Preview

Download Datasheet

View All

CFPT-9050 Series

ISSUE 6 ; 23 DECEMBER 2004

Recommended for New Designs

Delivery Options

■

Frequency Stability

■

Temperature: see table

Typical Supply Voltage Variation ±10% < ±0.2 ppm*

Typical Load Coefficient 15pF ±5pF < ±0.2 ppm*

Please contact our sales office for current leadtimes

Description

■

* Depending on frequency and output type

Frequency Adjustment

■

A highly versatile series of surface mountable

14.7 x 9.2 x 6.2mm temperature compensated voltage

controlled crystal oscillators (TCVCXOs) for applications

where small size and high performance are pre-

requisites. This oscillator uses C-MAC’s latest custom

ASIC "Pluto", a single chip oscillator and analogue

compensation circuit, capable of sub 0.3 ppm

performance. Its wide frequency range, operating

temperature range, drive capability, coupled with its

high stability and linear frequency pulling make it the

ideal reference oscillator. Its ability to function down to

a supply voltage of 2.4V and low power consumption

makes it particularly suitable for mobile applications

Three options with external Voltage Control applied to

pad 1:

A - Ageing adjustment: > ±5ppm (Standard Option)

B - No frequency adjustment. Initial calibration @ 25°C

< ±0.5 ppm

C - High Pulling ±10ppm to ±50ppm can be available

depending on frequency and stability options.

Please consult our sales office

■

Linearity

Slope

Input resistance

Modulation bandwidth

Standard control voltage ranges:

Without reference voltage

With reference voltage

< 1%

Positive

> 100kΩ

> 2kHz

Standard Frequencies

■

9.6, 10.0, 12.8, 19.44, 20.0, 38.88, 49.152, 51.84MHz

Waveform

SURFACE MOUNT

TCXOs

■

Square HCMOS 15pF load

Square ACMOS 50pF max. load

Sinewave 10kΩ // 10pF AC-coupled

Clipped sinewave 10kΩ // 10pF AC-coupled

- Vs=5.0V 2.5V±2V

- Vs=3.3V 1.65V±1V

- Vc=0V to Vref

■

Reference Voltage, Vref (HCMOS/ACMOS only)

■

Supply Voltage

■

Optional reference voltage output on pad 5, suitable for

potentiometer supply or DAC reference.

1. No output (standard option)

2. 2.2V, for Min. Vs>2.4V

3. 2.7V, for Min. Vs>3.0V

4. 4.2V, for Min. Vs>4.5V

Maximum load current (mA) = Vref /10

Operating range 2.4 to 6.0V, see table

Current Consumption

■

HCMOS Typically

≈

1+Frequency(MHz)*Supply(V)*{Load(pF)+15}*10

-3

e.g. 20MHz, 5V, 15pF

≈

4mA

ACMOS Typically

≈

1+Frequency(MHz)*Supply(V)*{Load(pF)+23}*10

-3

Sinewave, 6 to 12 mA depending on frequency

Clipped Sinewave, Typically

≈

1+Frequency(MHz)*1.2*{Load(pF)+30}*10

-3

■

For manual frequency adjustment (HCMOS/ACMOS output

only) connect an external 50kΩ potentiometer between

pad 5 (Reference Voltage) and pad 3 (GND) with wiper

connected to pad 1 (Voltage Control). Please specify

reference voltage as a part of the ordering code

Note: Please contact our sales office if a reference voltage

is required in combination with sine or clipped sinewave

output

Tri-state

Package Outline

■

14.7 x 9.2 x 6.2mm SMD

■

Ageing

■

Pad 2 open circuit or >0.6Vs output enabled

< 0.2Vs Tri-state

When Tri-stated, the output stage is disabled for all

output options, but the oscillator and compensation

circuit are still active (current consumption <1mA)

±1ppm maximum in first year

±3ppm maximum for 10 years

±1ppm maximum after reflow

■

Europe Tel: +44 (0)1460 270200

Americas Tel: +1 919 941 9333

Asia

Tel: +86 755 8826 5991

Fax: +44 (0)1460 72578

Fax: +1 919 941 9371

Fax: +86 755 8826 5990

Website: www.cmac.com

Recommended Resources

LM3914 drives 20 LED light-emitting columns circuit diagram

Remote control circuit schematic diagram

The module prohibits constant current and constant voltage function port wiring

Basic two-stage low-pass filter circuit

6V regulated power supply circuit with input short circuit protection

Traffic light control circuit diagram

ST MEMS Creative Competition Post 10 - Discussion and help on MLC issues: Some questions about MLC :Data training collection timeThe training PPT mentioned that you need to click start to start recording after the exercise begins ; but here is a question:Will this cause the...; 传媒学子 ST MEMS Sensor Creative Design Competition

First chance exception in nk.exe appears when wince starts?: When the system image is downloaded from the development workstation to the development board via the network, the development workstation sees that the image has been downloaded and wince starts to s...; xiaoxiangjin Embedded System

Have you ever bought a fake chip? How did you deal with it?: Today I saw a friend say "TLC2254AID (high impedance, micro power consumption, rail-to-rail) has been used in batches, but it was the original board. The power consumption of the chip purchased now is...; clark Buy&Sell

Scattered points: By the way, I would like to ask if WinCE5.0 is going to be eliminated. Should I still learn WinCE6.0 7.0 8.0 or something like that?: Scattered points: Let’s discuss whether WinCE5.0 is going to be eliminated, and whether programmers who are proficient in WinCE5.0 need to learn WinCE6.0 7.0 8.0 or something like that?...; duibuqi Embedded System

Problems with calling DDR2IP core simulation in ISE: I called the DDR2 IP core in ISE. There is an example in it that can be simulated. I want to change some of the inputs according to my input requirements, such as the control of the write port wr_en w...; 碧水2012 FPGA/CPLD

UCOS and UCGUI porting for Wanli LPC54102 development board: Yesterday I saw a guy transplanted the LPC54102 color screen driver and GUI. I was feeling irritable and didn't want to do anything, so I fiddled with the Wanli development board at home for a day. I ...; mars4zhu NXP MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components