EEWORLDEEWORLDEEWORLD

Part Number

Search

B37M08G999X99

Description
RF BNC Connector, Female, Panel Mount, Solder Terminal, Socket,
CategoryThe connector    The connector   
File Size1MB,43 Pages
ManufacturerMACOM
Websitehttp://www.macom.com
Download Datasheet Parametric View All

B37M08G999X99 Overview

RF BNC Connector, Female, Panel Mount, Solder Terminal, Socket,

B37M08G999X99 Parametric

Parameter NameAttribute value
MakerMACOM
Reach Compliance Codeunknown
Body/casing typeSOCKET
Characteristic impedance75 Ω
Connector typeRF BNC CONNECTOR
Contact to complete cooperationGOLD (63) OVER COPPER
Contact completed and terminatedGOLD (63) OVER COPPER
Contact point genderFEMALE
Contact materialBERYLLIUM COPPER/BRASS
Coupling typeBAYONET
DIN complianceNO
Filter functionNO
IEC complianceNO
insulator materialPTFE
JESD-609 codee4
MIL complianceNO
Manufacturer's serial numberBNC
Installation methodSTRAIGHT
Maximum operating frequency4 GHz
Panel mountingYES
Termination typeSOLDER
Base Number Matches1
What programmer should I use to program ATMEL626?
I would like to ask everyone, ATMEL626 24C128, which programmer can be used to burn this EEPROM? Or, what common chip can completely replace it? I have been looking for a long time but have not found ...
esobao 51mcu
TLV5619, VCA820 PCB schematics
[i=s] This post was last edited by paulhyde on 2014-9-15 03:32 [/i] TLV5619, VCA820 PCB schematic...
wangkanglin Electronics Design Contest
How to drive LCD
I want to use an ST microcontroller to directly drive an LCD screen. When I use a 1/2 bias drive method, the screen has ghosting. Then I use an analog 1/3 bias, and the com end uses a resistor divider...
啸月 stm32/stm8
PowerLogic Tutorial (Shanghai Yinli).
PowerLogic Tutorial (Shanghai Yinli)....
fighting PCB Design
[AT-START-F425 Review] + Hardware I2C and software simulation I2C speed comparison
1. Introduction This article uses AT32F425 to drive SSD1306 OLED to test the I2C rate. For detailed code operations on OLED, please refer to [GD32L233C-START Review] 6. Hardware I2C drive 0.96-inch OL...
freeelectron Domestic Chip Exchange
Please tell me what is the red striped area generated in the pcb after executing UPDATE PCB TO ...
I would like to ask, after executing UPDATE PCB TO ..., what is the red stripe area generated in the PCB? As shown in the figure below, what is the red stripe area where 2 is located and what is its f...
一沙一世 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2243  2680  1892  1136  590  46  54  39  23  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号