The offset (or zero) numbers with CHP = 1 are typically 3
μV
precalibration. Internal zero-scale calibration reduces this by about 1
μV.
Offset numbers with CHP = 0 can be up to
1 mV precalibration. Internal zero-scale calibration reduces this to 2
μV
typical. System zero-scale calibration reduces offset numbers with CHP = 1 and CHP = 0 to the order of the
noise. Gain errors can be up to 3000 ppm precalibration with CHP = 0 and CHP = 1. Performing internal full-scale calibrations on the 80 mV range reduces the gain error to less than
100 ppm for the 80 mV and 40 mV ranges, to about 250 ppm for the 20 mV range and to about 500 ppm on the 10 mV range. System full-scale calibration reduces this to the order of
the noise. Positive and negative full-scale errors can be calculated from the offset and gain errors.
14
These numbers are generated during life testing of the part.
15
Positive Full-Scale Error includes Offset Errors (Unipolar Offset Error or Bipolar Zero Error) and applies to both unipolar and bipolar input ranges. See Terminology.
16
Recalibration at any temperature will remove these errors.
17
Full-Scale Drift includes Offset Drift (Unipolar Offset Drift or Bipolar Zero Drift) and applies to both unipolar and bipolar input ranges.
18
Gain Error is a measure of the difference between the measured and the ideal span between any two points in the transfer function. The two points used to calculate the gain
error are positive full scale and negative full scale. See Terminology.
19
Gain Error Drift is a span drift and is effectively the drift of the part if zero-scale calibrations only were performed.
10
No Missing Codes performance with CHP = 0 and SKIP = 1 is reduced below 24 bits for SF words lower than 180 decimal.
11
The analog input voltage range on the AIN1(+) and AIN2(+) inputs is given here with respect to the voltage on the AIN1(–) and AIN2(–) inputs respectively.
12
The common-mode voltage range on the input pairs applies provided the absolute input voltage specification is obeyed.
13
The common-mode voltage range on the reference input pair (REF IN(+) and REF IN(–)) applies provided the absolute input voltage specification is obeyed.
14
These logic output levels apply to the MCLK OUT output only when it is loaded with a single CMOS load.
15
V
DD
refers to DV
DD
for all logic outputs expect D0, D1, ACX and
ACX
where it refers to AV
DD
. In other words, the output logic high for these four outputs is determined by AV
DD
.
16
This number represents the total drift of the channel with a zero input and the DAC output near full scale.
17
After calibration, if the input voltage exceeds positive full scale, the converter will output all 1s. If the input is less than negative full scale, the device outputs all 0s.
18
These calibration and span limits apply provided the absolute input voltage specification is obeyed. The offset calibration limit applies to both the unipolar zero point and the
bipolar zero point.
Specifications subject to change without notice.
TIMING CHARACTERISTICS
Parameter
Master Clock Range
t
1
t
2
Read Operation
t
3
t
4
t
5 4
t
5A4, 5
t
6
t
7
t
8
t
9 6
t
10
Write Operation
t
11
t
12
t
13
t
14
t
15
t
16
1
5
50
50
0
0
0
60
80
0
60
80
100
100
0
10
80
100
0
30
25
100
100
0
1, 2
(AV
DD
= +4.75 V to +5.25 V; DV
DD
= +2.7 V to +5.25 V; AGND = DGND = 0 V; f
CLK IN
= 4.9152 MHz;
Input Logic 0 = 0 V, Logic 1 = DV
DD
unless otherwise noted).
Units
MHz min
MHz max
ns min
ns min
ns min
ns min
ns min
ns max
ns max
ns min
ns max
ns max
ns min
ns min
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns min
ns min
ns min
Conditions/Comments
For Specified Performance
SYNC
Pulsewidth
RESET
Pulsewidth
RDY
to
CS
Setup Time
CS
Falling Edge to SCLK Active Edge Setup Time
3
SCLK Active Edge to Data Valid Delay
3
DV
DD
= +4.75 V to +5.25 V
DV
DD
= +2.75 V to +3.3 V
CS
Falling Edge to Data Valid Delay
DV
DD
= +4.75 V to +5.25 V
DV
DD
= +2.7 V to +3.3 V
SCLK High Pulsewidth
SCLK Low Pulsewidth
CS
Rising Edge to SCLK Inactive Edge Hold Time
3
Bus Relinquish Time after SCLK Inactive Edge
3
SCLK Active Edge to
RDY
High
3, 7
CS
Falling Edge to SCLK Active Edge Setup Time
3
Data Valid to SCLK Edge Setup Time
Data Valid to SCLK Edge Hold Time
SCLK High Pulsewidth
SCLK Low Pulsewidth
CS
Rising Edge to SCLK Edge Hold Time
Limit at T
MIN
to T
MAX
(B Version)
NOTES
1
Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of DV
DD
) and timed from a voltage level of 1.6 V.
2
See Figures 18 and 19.
3
SCLK active edge is falling edge of SCLK with POL = 1; SCLK active edge is rising edge of SCLK with POL = 0.
4
These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross the V
OL
or V
OH
limits.
5
This specification only comes into play if
CS
goes low while SCLK is low (POL = 1) or if
CS
goes low while SCLK is high (POL = 0). It is primarily required for
interfacing to DSP machines.
6
These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then
extrapolated back to remove effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the true bus
relinquish times of the part and as such are independent of external bus loading capacitances.
7
RDY
returns high after the first read from the device after an output update. The same data can be read again, if required, while
RDY
is high, although care should
be taken that subsequent reads do not occur close to the next output update.
–4–
REV. B
AD7730/AD7730L
ABSOLUTE MAXIMUM RATINGS*
(T
A
= +25°C unless otherwise noted)
AV
DD
to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
AV
DD
to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
DV
DD
to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
DV
DD
to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . . . –5 V to +0.3 V
AV
DD
to DV
DD
. . . . . . . . . . . . . . . . . . . . . . . . . –2 V to +5 V
Analog Input Voltage to AGND . . . . –0.3 V to AV
DD
+ 0.3 V
Reference Input Voltage to AGND . . –0.3 V to AV
DD
+ 0.3 V
AIN/REF IN Current (Indefinite) . . . . . . . . . . . . . . . . 30 mA
Digital Input Voltage to DGND . . . . –0.3 V to DV
[align=left] Today, everyone has a mobile phone. This phone may be an iPhone, an Android phone, or a Windows Phone. [/font] No matter which smartphone it is, it is actually a powerful development plat...
Reprint address: [url]http://apps.hi.baidu.com/share/detail/22816323[/url] Copyright belongs to the original author. I have done experiments before and found that the INF error of this emulator appear...
[table=98%,rgb(238, 238, 238)] [tr][td]Use uboot instead of eboot. I modified uboot to support booting wince/linux/android series, support INAND/SDMMC to start wince. Do I need to comply with regulati...
I want to make an RPC remote function call module based on ARM embedded system. I wrote a small test program using the template generated by RPCGEN, but I don't know how to port it to the development ...
Hi everyone, last time I wrote a [[url=http://www.kaleidscope.cn:1020/archives/2678][b]ZigBee whitelist solution[/b][/url]], many friends have asked me to make a module related to channels, PANID and ...
A very simple circuit is to connect the 4 SPI ports of X5043 to the SPI of ARM (using STM32). X5043 is powered by 3.3V and the reset threshold is 2.7V. After powering on, it does nothing. The Reset pi...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
To understand how and why OLED power supply affects display image quality, you must first understand OLED display technology and power supply requirements. This article will explain the latest OLED...[Details]
introduction
Incandescent bulbs can emit a variety of light, but in specific applications, only green, red, and yellow light are usually needed - such as traffic lights. If an incand...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
