Operating Temperature Range ........................... -40NC
to +85NC
Storage Temperature Range ............................
-65NC
to +150NC
Junction Temperature ..................................................... +150NC
Lead Temperature (soldering, 10s) ................................. +300NC
Soldering Temperature (reflow) .......................................+260NC
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Package Thermal Characteristics
(Note 1)
Junction-to-Ambient Thermal Resistance (B
JA
)
.............3.3NC/W
Note 1:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to
www.maximintegrated.com/thermal-tutorial.
Electrical Characteristics
(V
DD
= +2.37V to +5.5V, V
P-P
= +10V to +12.5V, V
NN
= 0 to -200V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are V
DD
=
+3.3V, V
NN
= -100V, V
P-P
= +12V at T
A
= +25NC.)
(Note 2)
PARAMETER
POWER SUPPLIES
V
DD
Logic Supply Voltage
V
NN
Supply Voltage
V
P-P
Supply Voltage
V
DD
Static Current
V
DD
Dynamic Current
V
NN
Static Current
V
NN
Supply Dynamic Current
(All Channel Switching
Simultaneously)
V
P-P
Supply Static Current
V
P-P
Supply Dynamic Current
(All Channel Switching
Simultaneously)
V
CC10
Static Output Voltage
V
CC10
Dynamic Output
Voltage
V
DD
V
NN
V
P-P
I
DDS
I
DD
I
NNS
I
NN
I
PPS
I
PP
V
CC10s
V
CC10
V
DD
= +5V, f
CLK
= 5MHz,
f
DIN
= 2.5MHz
All switches remain on or off,
SW_ = GND
V
P-P
= +12V, V
NN
= -100V,
f
TURN_ON/OFF
= 50kHz, SW_ = GND
All switches remain on or off,
SW_ = GND
V
P-P
= +12V, V
NN
= -100V,
f
TURN_ON/OFF
= 50kHz, SW_ = GND
V
P-P
= +12V, all switches remain on or
off, SW_ = GND
V
P-P
= +12V, I
OUT
= 30mA
10
9.5
2.37
-200
10
12
25
100
15
4.3
75
5.4
10.5
10.25
5.5
0
12.5
50
200
25
8
160
9
V
V
V
µA
µA
µA
mA
µA
mA
V
V
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
www.maximintegrated.com
Maxim Integrated
│
2
MAX4968B/MAX4968C
16-Channel, Linear, High-Voltage Analog Switches
in BGA Package
Electrical Characteristics (continued)
(V
DD
= +2.37V to +5.5V, V
P-P
= +10V to +12.5V, V
NN
= 0 to -200V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are
V
DD
= +3.3V, V
NN
= -100V, V
P-P
= +12V at T
A
= +25NC.)
(Note 2)
PARAMETER
SWITCH CHARACTERISTICS
Analog Dynamic Signal Range
Small-Signal
On-Resistance
Small-Signal
On-Resistance Matching
Small-Signal
On-Resistance Flatness
Output Switch Bleed Resistor
Switch-Off Leakage
Switch-Off DC Offset
Switch-On DC Offset
Switch Output Isolation Diode
Current
SWITCH DYNAMIC CHARACTERISITICS
Turn-On Time
Turn-Off Time
Maximum V
SW_
Slew Rate
Off-Isolation
Crosstalk
SW_ Off-Capacitance
SW_ On-Capacitance
Output Voltage Spike
Large-Signal Analog
Bandwidth (-3dB)
Small-Signal Analog Bandwidth
(-3dB)
Charge Injection
LOGIC LEVELS
Logic-Input Low Voltage
Logic-Input High Voltage
Logic-Output Low Voltage
V
IL
V
IH
V
OL
I
SINK
= 1mA
V
DD
-
0.75
0.4
0.75
V
V
V
t
ON
t
OFF
dV/dt
V
ISO
V
CT
C
SW_(OFF)
C
SW_ (ON)
V
SPK
f
BW_L
f
BW_S
Q
V
SW_
= +1V, R
L
= 100Ω, V
NN
= -100V,
from SET to
V
SW_
= +0.9V
V
SW_
= +1V, R
L
= 100Ω, V
NN
= -100V,
from CLR to
V
SW_
= +0.9V
C
L
= 100pF
f = 5MHz, R
L
= 50Ω
f = 5MHz, R
L
= 50Ω
f = 1MHz, small signal close to zero
f = 1MHz, small signal close to zero
R
L
= 50Ω
C
LOAD
= 200pF, 60V amplitude
sinusoidal burst, 1% duty cycle
C
LOAD
= 200pF, 100mV amplitude
sinusoidal
V
NN
= -100V, Figure 1
-150
30
50
150
20
-68
-69
8
14
+150
2
2
5
3.5
µs
µs
V/ns
dB
dB
pF
pF
mV
MHz
MHz
pC
V
SW_
R
ONS
ΔR
ONS
R
ONF
R
INT
I
SW_(OFF)
AC operation only, f > 500kHz
V
P-P
= +12V, V
NN
= -100V, V
SW_
= 0V,
I
SW_
= 5mA
V
P-P
= +12V, V
NN
= -100V,
I
SW_
= 5mA
AC measured, f
SW
= 0.5MHz,
V
SW
= 80V
P-P
, R
LOAD
= 50Ω,
V
P-P
= +12V, V
NN
= -100V
MAX4968C only
V
SW
= 0V, switch off (MAX4968B only)
R
L
= 100kΩ on both sides
R
L
= 100kΩ on both sides
300ns pulse width, 2% duty cycle
-15
-15
3.0
30
V
NN
18
3
2
40
0
50
1
+15
+15
V
NN
+210
34
V
Ω
%
%
kΩ
ΩA
mV
mV
A
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
www.maximintegrated.com
Maxim Integrated
│
3
MAX4968B/MAX4968C
16-Channel, Linear, High-Voltage Analog Switches
in BGA Package
Electrical Characteristics (continued)
(V
DD
= +2.37V to +5.5V, V
P-P
= +10V to +12.5V, V
NN
= 0 to -200V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are
V
DD
= +3.3V, V
NN
= -100V, V
P-P
= +12V at T
A
= +25NC.)
(Note 2)
PARAMETER
Logic-Output High Voltage
Logic-Input Capacitance
Logic-Input Leakage
Pulldown Resistor in SET Pin
CLK Frequency
DIN-to-CLK Setup Time
DIN-to-CLK Hold Time
CLK to LE Setup Time
LE
Low Pulse Width
CLR High Pulse Width
SET High Pulse Width
CLK Rise and Fall Times
CLK to DOUT Delay
SYMBOL
V
OH
C
IN
I
IN
R
PULLDOWN
f
CLK
t
DS
t
DH
t
CS
t
WL
t
WC
t
WS
t
R
, t
F
t
DO
V
DD
= +5V ±10%, C
DOUT
= 15pF
V
DD
= +2.5V ±5%, C
DOUT
= 15pF
4
4
28
12
16
16
50
28
45
-1
65
100
CONDITIONS
I
SOURCE
= 1mA
MIN
V
DD
-
0.4
5
+1
140
25
TYP
MAX
UNITS
V
pF
µA
kΩ
MHz
ns
ns
ns
ns
ns
ns
ns
ns
TIMING CHARACTERISTICS (Figure 2)
Note 2:
All devices are 100% tested at T
A
= +85NC.
Limits over the operating temperature range are guaranteed by design.
Reprinted from [url]http://blog.sina.com.cn/s/blog_679f93560101201q.html[/url] [b]FIS[/b] SATA uses frame information structure (FIS) to transmit data and commands between HBA and Device. [b]Applicati...
I want to use a general-purpose timer to generate PWM, but for some reason the program is always wrong. I've attached the program below. Please help. void Init_Timer_PWM(void) { SysCtlPeripheralEnable...
[b]Install a TMS320F2802x with a free download[/b] [url=http://www.ti.com/lit/ds/sprs523i/sprs523i.pdf]http://www.ti.com/lit/ds /sprs523i/sprs523i.pdf[/url] PDF Full-Scale Reference Guide [b]CPU User'...
After reading the BLDM control scheme, there is one thing I don't quite understand. Please give me some advice! What is the function of the PWM generated by the control chip? Is it used for speed regu...
The bd682 pnp Darlington tube cannot be driven. A 1k resistor is connected in series with the B pole, the E pole is 5V, and there is no output voltage at the C pole?...
"Have you set your calendar reminder?"
On August 24, Nvidia Robotics' official account posted a photo of a black gift box on a social media platform, with an attached greeting card sig...[Details]
As the number of cars increases, environmental pressures are also increasing. At this time, some people are saying that new energy vehicles are energy-efficient and environmentally friendly, and ar...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
Capable of providing precise and efficient thermal management for artificial intelligence computing power, intelligent sensing and autonomous driving systems
Shenzhen, ...[Details]
For autonomous vehicles to safely navigate the road, they must identify far more complex objects than just traffic lights, pedestrians, and other familiar objects. Among these obstacles is a crucia...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
Common methods for troubleshooting roller press bearing wear include repair welding, thermal spraying, brush plating, and scrapping and replacement. However, these methods are often subject to asse...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
Speaking of the problem of vehicle spontaneous combustion, whether it is a pure electric vehicle or a fuel vehicle, there will be incidents of spontaneous combustion. For the same spontaneous combu...[Details]
Wearable technology is taking off, with applications evolving rapidly, from smartwatches to fitness trackers and even smart wigs! Bluetooth Smart is at the center of this revolution. This is the se...[Details]
The composition of the water heater
The water heater itself is divided into the following parts:
1. Water tank.
This is where the water heater is filled with water and where the wate...[Details]
Traditionally, electrical energy is transmitted primarily through wires, requiring direct physical contact between the power source and the load. With the increasing number of electrical devices in...[Details]
With the growth of the Internet of Things (IoT), wearable, and portable devices, consumers are growing weary of cluttered cables and the need for frequent battery recharges. The benefits of wireles...[Details]
As automotive technology develops at an ever-increasing pace, the performance requirements for automotive internal structures, components, and accessories are becoming increasingly demanding. The d...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
