ADALM2000 is a 9-in-1 portable test and measurement instrument launched by ADI.
Open sourced by Bilibili up, DCDC-LDO secondary step-down power supply, tc1047 for cold-end compensation, built-in curve fitting calibration function, and supports 65W gallium nitride charger.
ESC is the abbreviation of Electric Speed Controller, that is, electronic speed controller, or ESC for short. The author is Benjamin Vedder, so it is called VESC. You may have heard of it, which is Benjamin ESC. This project is mainly divided into several parts, VESC firmware, bill of materials, VESC hardware, and VESC tool software. It is a very complete software and hardware project, and the supporting software is also excellent.
A low-cost PD-powered reflow soldering heating plate that uses a cermet heater (MCH) instead of a PCB heating plate for heating. It has a USB Type-C input port and can be powered by a 60W (65W) PD power supply.
With just a Raspberry Pi Pico, an analog switch and an op amp, you can build a powerful SDR receiver covering the LW, MW and SW bands. Capable of receiving signals from halfway around the world.
The cost of the board should be less than 50RMB, and it provides a lot of information, which is very suitable for novices to use as a development board to learn Linux.
There are three boards in total, USB, FPGA and Sensor board. The FPGA board features a Lattice Crosslink NX LIFCL-40 and the required power regulator, and the USB board features a CYUSB3014 USB 3.0 SuperSpeed controller.
This open source ferry robot has unique functions such as the anti-interference standing ability of a tumbler and automatic roll-up.
SmartKnob is an open source input device with software-configurable stops and virtual locators. The brushless gimbal motor is paired with a magnetic encoder to provide closed-loop torque feedback control, allowing the feel of the detent and stop to be dynamically created and adjusted.
Bllimpduino 2 is a very low cost open source autonomous airship. It consists of Arduino M0 airship controller board and on-board WIFI and laser sensors. Two vector differential thrusters and one lift thruster. The design is simple, yet exciting.
ScopeFun is an open source all-in-one instrumentation platform. It includes oscilloscopes, arbitrary waveform generators, spectrum analyzers, logic analyzers and digital pattern generators.
Little Bee is an affordable, high-performance current probe and magnetic field probe that allows you to debug and analyze electronic devices more efficiently.
Portenta X8 is a powerful industrial-grade SOM with a pre-installed Linux operating system onboard and can run device-independent software thanks to its modular container architecture. Securely perform OS/application OTA updates with onboard Wi-Fi/Bluetooth® Low Energy connectivity. It is basically two industrial products combined into one, with a power of no less than 9 cores. Utilize the Arduino environment to perform real-time tasks, while Linux handles high-performance processing. Portenta X8 features NXP® i.MX 8M Mini Cortex®-A53 quad-core up to 1.8GHz per core + 1x Cortex®-M4 up to 400MHz, and STMicroelectronics STM32H747 dual-core Cortex®-M7 up to 480Mhz +M4 32-bit Arm® MCU, up to 240MHz.
The author opens up the schematic diagram and supporting Raspberry Pi code. The simulation bandwidth is already 30MHz, and the frequency response is very close to the theoretical simulation, with a difference of about 0.02dB between 1kHz and 30MHz.
Uses infrared light sensing to determine changes in blood oxygen levels in the brain in real time. Use the device in less than ten minutes to learn how to directly change blood flow to your brain. Neurons do not store energy, so regional brain activity is closely related to changes in blood oxygenation, where healthy blood flow patterns are essential for high function and growth of the brain.
Ideal for running network devices such as small switches, home routers, and WLAN access points.
Flipper Zero is a portable multi-tool designed for developers and geeks with a toy-like body. It enjoys exploring digital content such as radio protocols, access control systems, hardware, and more. It's completely open source and customizable, so you can extend it in any way you like.
Starfish is a pick and place machine control board built on the Raspberry Pi RP2040 microcontroller and Trinamic TMC2209 motor driver. This control board has some similarities to a 3D printer control board, but it has some unique issues to solve—including controlling solenoids and communicating with vacuum sensors. All board information is open source, and detailed explanations are provided to help you copy successfully.
You can certainly buy desktop power supplies, but they're not cheap. As the current capacity and output voltage quantity increase, so does the price. While a commercial desktop power supply is certainly worth the investment, you may want to consider a cheaper solution. Adapt an old computer power supply for use on your workbench. Computer power supplies have all the voltages you need and some very impressive current capabilities.
EEWorld
subscription
account
EEWorld
service
account
Automotive
development
community
Robot
development
community
About Us Customer Service Contact Information Datasheet Sitemap LatestNews
Room 1530, 15th Floor, Building B,
No.18 Zhongguancun Street,
Haidian District,
Beijing, Postal Code: 100190
China
Telephone: 008610 8235 0740
京公网安备 11010802033920号
