EEWORLDEEWORLDEEWORLD

Part Number

Search
 

MAX436CSD

Part NumberMAX436CSD
CategoryAnalog mixed-signal IC    Amplifier circuit   
File Size14651.39,17 Pages
ManufacturerRochester Electronics
Websitehttps://www.rocelec.com/
Download Datasheet Parametric

Alternative parts

Part Number Manufacturer Description
MAX436ESD Rochester Electronics LLC Basic information about MAX436ESD amplifier:MAX436ESD is an OPERATIONAL AMPLIFIER. The commonly used...
MAX436ESD-T Rochester Electronics LLC Basic information of MAX436ESD-T amplifier:MAX436ESD-T is an OPERATIONAL AMPLIFIER. The commonly use...
MAX436CSD+ Maxim Integrated Products Operational Amplifiers - Op Amps
MAX436CSD+T Maxim Integrated Products Basic information of MAX436CSD+T amplifier:MAX436CSD+T is an OPERATIONAL AMPLIFIER. Commonly used pa...
MAX436CSD-T Maxim Integrated Products Operational Amplifiers - Op Amps
MAX436ESD+T Maxim Integrated Products Basic information of MAX436ESD+T amplifier:MAX436ESD+T is an OPERATIONAL AMPLIFIER. Commonly used pa...
MAX436ESD+ Maxim Integrated Products Basic information about MAX436ESD+ amplifier:MAX436ESD+ is an OPERATIONAL AMPLIFIER. Commonly used p...

MAX436CSD Overview

Basic information of MAX436CSD amplifier:

MAX436CSD is an OPERATIONAL AMPLIFIER. The commonly used packaging method is SOP,

MAX436CSD amplifier core information:

The minimum operating temperature of the MAX436CSD is 70 °C. Its peak reflow temperature is 240°C and its maximum average bias current is 5 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the MAX436CSD has a nominal slew rate of 850 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the MAX436CSD gain becomes 0.707 times the low-frequency gain is 275000 kHz.

The nominal supply voltage of the MAX436CSD is 5 V, and its corresponding nominal negative supply voltage is -5 V. The input offset voltage of the MAX436CSD is 3000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of MAX436CSD:

The width of MAX436CSD is: 3.9 mm and the length is 8.65 mm. MAX436CSD has 14 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 14

MAX436CSD amplifier additional information:

Its temperature grade is: COMMERCIAL. And its humidity sensitivity level is: 1. The MAX436CSD is not Rohs certified. It contains lead. The corresponding JESD-30 code is: R-PDSO-G14.

The corresponding JESD-609 code is: e0. The packaging code of MAX436CSD is: SOP. The materials used in the MAX436CSD package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The MAX436CSD package pin formats are: SMALL OUTLINE.

Its terminal forms are: GULL WING. The maximum seat height is 1.75 mm.

Software encryption under wince? ?
Dear experts, I am using VS2005 on WINCE. How can I encrypt the software I wrote so that it can only run on one machine and cannot be copied to other machines? I have tried to query the registry and the machine number, but the machine numbers of the ...
ziranyouxin Embedded System
What's the deal with the TI Expert label? Is it from TI?
What's the deal with the TI expert label stamp? Is it from TI? Yes, TI's expert reply post will have an icon ...
wangfuchong Microcontroller MCU
Thermal Micro Printer Reference Design
Thermal Micro Printer Reference Design with Block Diagram Haha, yes ...
taburiss001 Microcontroller MCU
Recently DIY digital power supply, begging for TI MCU and power management chip
Recently, TI and EEWORLD organized everyone to DIY a digital power supply for experiment. As an enthusiast and a novice, I also hope to have my own digital power supply, so after understanding some indicators, I started to take action. From last w...
海得工控 DIY/Open Source Hardware
Clock problem in cycloneIII EP3C5E144C8N
How to connect the clocks CLK and CLK ? If I want to output a clock through the PLL, which pin should the output clock be locked to? Please help me! ! ! ! ! ! Why doesn't anyone help me answer this question? ? ? ? ? ? It can be any pin between CLK0~C...
ominous2012 FPGA/CPLD
How to configure EPCS chip using JTAG
Instead of using the AS interface, you can use the JTAG interface to configure the EPCS device. The specific steps are as follows: 1. Open the project in QuartusII, then compile and link to generate the JTAG configuration file .sof; 2. Select Fil...
eeleader FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Site Related: China chips Training TI Training Datasheet EEWORLD

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Search Index   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190

Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号