1. Calculated using MIL-HDBK-217F with nominal input voltage at full load.
All specifications typical at T
A
=25°C, nominal input voltage and rated output current unless otherwise specified.
www.murata-ps.com/support
KDC_LMEC.G01
Page 1 of 4
LME Series
Isolated 250mW Single Output DC-DC Converters
TEMPERATURE CHARACTERISTICS
Parameter
Specification
Storage
Cooling
Conditions
All output types
Free air convection
Min.
0
-50
Typ.
Max.
70
130
Units
°C
TEMPERATURE DERATING GRAPH
0.375
TOLERANCE ENVELOPE
+10%
+5%
V
NOM
Typical
L
Output Power (W)
Output Voltage
0.250
0.125
0
70°C
Safe Operating
Area
125°C
0
50
100
Ambient Temperature (°C)
150
oad Line
+2.5%
-2.5%
-7.5%
10
75
50
25
Output Load Current (%)
100
The voltage tolerance envelope shows typical load regulation characteristics for this product series. The toler-
ance envelope is the maximum output voltage variation due to changes in output loading.
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions LME series of DC-DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no specific agency approvals, such as the LME series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The LME series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of
260°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped
over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in
this series are backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
APPLICATION NOTES
Minimum Load
The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in an
increase in output voltage, which may rise to typically double the specified output voltage if the output load falls to less than 5%.
www.murata-ps.com/support
KDC_LMEC.G01
Page 2 of 4
LME Series
Isolated 250mW Single Output DC-DC Converters
PACKAGE SPECIFICATIONS
MECHANICAL DIMENSIONS
DIP Package
11.6±0.15 [0.457±0.006]
PIN CONNECTIONS - 8 PIN DIP
SIP Package
Pin
1
4
5
7
Function
-V
IN
+V
IN
+V
OUT
-V
OUT
LME
XXXXDC
XYYWW
9.9±0.15 [0.390±0.006]
11.53±0.2 [0 .454±0.008]
PIN CONNECTIONS - 4 PIN SIP
Pin
Function
-V
IN
+V
IN
-V
OUT
+V
OUT
6.9±0.15 [0.272±0.006]
10.00±0.25 [0 .394±0.010]
XYYWW
0.40 [0.016] MIN
LME
XXXXSC
S
4.10±0.5 [0.161±0.020]
1
2
3
4
0.5±0.05 [0.020±0.002]
1.99±0.25 [0.078±0.010]
4.10±0.5 [0 .161±0.020]
1
2
3
4
2.54 [0.100]
1
1.14±0.25 [0.045±0.010]
7.62 [0.300]
0.50±0.05 [0 .020±0.002]
0.25±0.05 [0 .010±0.002]
4
(2.21 [0.087])
7
0.25±0.05 [0.010±0.002]
5
5.08 [0.200]
7.62 [0.300]
(1.13 [0.044])
+0.15
6.10 -0.20
[
0.240 +0.006
-0.008
]
All dimensions in mm (inches) Controlling dimension is mm.
SIP: All pins on a 2.54 (0.100) pitch and within ±0.1 (0.004) of true position from pin 1 at seating plane ‘S’
DIP: All pins on a 2.54 (0.100) pitch and within ±0.25 (0.010) of true position
Weight: 1.30g (SIP) 1.48g (DIP)
www.murata-ps.com/support
KDC_LMEC.G01
Page 3 of 4
LME Series
Isolated 250mW Single Output DC-DC Converters
PACKAGE SPECIFICATIONS (continued)
RECOMMENDED FOOTPRINT DETAILS
8 Pin DIP Package
2.54 (0.100)
4 Pin SIP Package
4 HOLES
0.1 (0.00394)
1.15 (0.0453)
Ø
1.00 (0.0394)
x4 HOLES
1.15 0.045
Ø
Ø
1.00 0.039
[
]
2.54
(0.1)
2.54 (0.100)
All dimensions in mm (inches) Controlling dimension is mm.
2.54
(0.1)
TUBE OUTLINE DIMENSIONS
8 Pin DIP Tube
12.0 [0.472]
4 Pin SIP Tube
9.3 [0.366]
12.43 [0.489]
14.5 [0.571]
18.0 [0.709]
5.07±0.80 [0.200±0.03]
5.05 [0.199]
5.0 [0.197]
Unless otherwise stated all dimensions in inches (mm ±0.5mm).
To thank the forum for providing the group purchase opportunity of the development board again, I have sorted out the relevant information, all of which are transferred from the Internet, so that you ...
I have finished learning the internal resources of the lm3s series (but I am not very proficient in it). Should I install a system now? Which system should I install? Please give me some advice. Most ...
该书序言中有一段话。TheFuture?People often ask, “ Would you encourage your son or daughter to go into engineering? ” Ireply, “ Yes, if it is analog circuit design. ”Theysay,“ Explain! ”I respond, “ My friends a...
A small program that collects audio signals and outputs waveforms. You can see a relatively good effect in the simulator in EVC. The zero line is smooth and straight when there is no signal. Download ...
I want to expand a 64Kcy7c1021cv33 RAM for debugging. Does anyone have a circuit diagram for this? I don't know whether to connect DS or PS.Thanksbrettwkl@163.com...
Hello everyone!
I am a novice in the field of electronic information development. Now I want to learn a system based on the ARM Cortex M0 core. I don’t know how to get started? I seem to have only som...
Tesla and BYD, vying for dominance in the global electric vehicle market, are reportedly considering adopting Samsung's AMOLED (active-matrix organic light-emitting diode) technology for their next...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
Reflow soldering, a common soldering method in modern electronics manufacturing, primarily melts solder paste and pads to form solder joints. With technological advancements, soldering equipment ha...[Details]
introduction
With the development of digital and network technologies, broadcasting technology has become increasingly diversified, with the most significant trend being the transition from an...[Details]
To understand why car engines need gearboxes, we must first understand the characteristics of different types of engines. An engine refers to a machine that can convert a form of energy into kineti...[Details]
Long ago, the lifespan of cars in my country was 15 years. Once a car reached 15 years old, it was forced to be scrapped. However, the policy was later changed. As long as the car does not exceed 6...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
introduction
Sonar imaging is of great significance in marine resource development and defense. Its long range, intuitive display of the observed area, and target identification make it widely...[Details]
Overview
As handheld voice communication devices become more and more popular, they are increasingly used in noisy environments, such as airports, busy roads, crowded bars, etc. In such noisy ...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
"We have successfully launched the first version of our dedicated chip for EMB brake-by-wire. Second-generation samples have also been successfully completed, and we are actively planning a third-g...[Details]
Intel®
Xeon®
6
-
core processors now support the new Amazon EC2 R8i and R8i-flex instances on Amazon Web Services (AWS).
These new instances offer superior performance and fast...[Details]
With the increasing popularity of automated equipment, linear modules, a common auxiliary device for automated equipment, have also seen a bright future. In particular, in recent years, many small ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
