a. Signals on NC, NO, or COM or IN exceeding V+ will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
b. Refer to IPC/JEDEC (J-STD-020A)
c. All bumps soldered to PC board.
d. Derate 3.1 mW/°C above 70 °C.
www.vishay.com
2
Document Number: 72505
S11-0303-Rev. D, 28-Feb-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Product is End of Life
DG3001, DG3002, DG3003
Vishay Siliconix
SPECIFICATIONS
(V+ = 3 V)
Test Conditions
Otherwise Unless Specified
Parameter
Analog Switch
Analog Signal Range
d
On-Resistance
d
R
ON
Flatness
d
R
ON
Match
d
Switch Off Leakage Current
f
Symbol
V
NO
, V
NC
,
V
COM
R
ON
R
ON
Flatness
ΔR
ON
I
NO(off)
I
NC(off)
I
COM(off)
Channel-On Leakage Current
f
Digital Control
Input High Voltage
Input Low Voltage
Input Capacitance
d
Input Current
d
Dynamic Characteristics
Turn-On Time
d
Turn-Off Time
d
Limits
- 40 °C to 85 °C
Temp.
a
Min.
b
Typ.
c
Max.
b
Unit
V+ = 3 V, ± 10 %,V
IN
= 0.4 V or 2 V
e
Full
V+ = 2.7 V, V
COM
= 1.5 V
I
NO
, I
NC
= 10 mA
V+ = 2.7 V, V
COM
= 0 to V+
I
NO
, I
NC
= 10 mA
Room
Full
Room
Room
Room
Full
Room
Full
Room
Full
Full
Full
Full
V
IN
= 0 or V+
Full
Room
Full
Room
Full
Room
C
L
= 1 nF, V
GEN
= 0 V, R
GEN
= 0
Ω,
figure 3
R
L
= 50
Ω,
C
L
= 5 pF, f = 100 kHz
Room
Room
Room
Room
Room
0
0.4
0.1
0.01
-1
- 10
-1
- 10
-1
- 10
2
V+
0.7
0.8
0.2
0.05
1
10
1
10
1
10
V
Ω
V+ = 3.3 V,
V
NO
, V
NC
= 0.3 V/3 V, V
COM
= 3 V/0.3 V
V+ = 3.3 V, V
NO
, V
NC
= V
COM
= 0.3 V/3 V
nA
I
COM(on)
V
INH
V
INL
C
in
I
INL
or I
INH
0.4
5
-1
47
40
1
6
64
- 70
- 70
100
340
2.7
3.3
0.1
1
1
71
59
V
pF
µA
t
ON
t
OFF
t
d
Q
INJ
OIRR
X
TALK
C
NO(off)
C
NC(off)
C
ON
V+
I+
V
IN
= 0 or V+
V
NO
or V
NC
= 2 V, R
L
= 300
Ω,
C
L
= 35 pF
figure 1 and 2
ns
Break-Before-Make Time
d
Charge Injection
d
Off-Isolation
d
Crosstalk
d
N
O
, N
C
Off Capacitance
d
Channel-On
Power Supply
Positive Supply Range
Capacitance
d
pC
dB
V
IN
= 0 or V+, f = 1 MHz
pF
Negative Supply Current
V
µA
Notes:
a. Room = 25 °C, full = as determined by the operating suffix.
b. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
c. Typical values are for design aid only, not guaranteed nor subject to production testing.
d. Guarantee by design, nor subjected to production test.
e. V
IN
= input voltage to perform proper function.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Document Number: 72505
S11-0303-Rev. D, 28-Feb-11
www.vishay.com
3
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Product is End of Life
DG3001, DG3002, DG3003
Vishay Siliconix
TYPICAL CHARACTERISTICS
(25 °C, unless otherwise noted)
2.00
1.75
T = 25 °C
I
S
= 10 mA
R
ON
- On-Resistance (Ω)
1.00
V+
= 3
V
I
S
= 10 mA
0.80
R
ON
- On-Resistance ( )
1.50
1.25
1.00
0.75
0.50
0.25
V+ = 3.3 V
0.00
0
1
2
3
V
COM
- Analog Voltage (V)
4
5
V+ = 1.8 V
V+ = 2 V
V+ = 2.7 V
V+ = 3 V
V+ = 5 V
0.60
85
°C
25 °C
0.40
- 40 °C
0.20
0.00
0.0
0.5
1.0
1.5
2.0
2.5
3.0
V
COM
- Analog
Voltage
(V)
R
ON
vs. V
COM
and Supply Voltage
10 000
R
ON
vs. Analog Voltage and Temperature
100 mA
10 mA
V+ = 5 V
1000
I+ - Supply Current (nA)
V+ = 5 V
V
IN
= 0 V
100
I+ - Supply Current (A)
1 mA
100 µA
10 µA
1 µA
100 nA
10 nA
10
1
- 60
1 nA
- 40
- 20
0
20
40
60
80
100
10
100
1K
10 K
100 K
1M
10 M
Temperature (°C)
Input Switching Frequency (Hz)
Supply Current vs. Temperature
1000
V+ = 5 V
I
COM(on)
Leakage Current (pA)
Supply Current vs. Input Switching Frequency
250
200
150
100
50
0
- 50
- 100
- 150
- 200
I
COM(on)
I
NO(off)
, I
NC(off)
I
COM(off)
V+ = 5 V
Leakage Current (pA)
100
I
COM(off)
I
NO(off)
, I
NC(off)
10
- 60
- 250
- 40
- 20
0
20
40
60
80
100
0
1
2
3
4
5
Temperature (°C)
V
COM
, V
NO
, V
NC
- Analog Voltage (V)
Leakage Current vs. Temperature
Leakage vs. Analog Voltage
www.vishay.com
4
Document Number: 72505
S11-0303-Rev. D, 28-Feb-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Product is End of Life
DG3001, DG3002, DG3003
Vishay Siliconix
TYPICAL CHARACTERISTICS
(25 °C, unless otherwise noted)
100
90
t
ON
, t
OFF
- Switching Time (ns)
80
70
60
50
40
t
OFF
V+ = 3 V
30
20
10
0
- 60
- 40
- 20
0
20
40
60
80
100
t
OFF
V+ = 2 V
t
ON
V+ = 3 V
t
ON
V+ = 2 V
Loss, OIRR, X
TALK
(dB)
10
0
LOSS
- 10
- 20
- 30
- 40
- 50
- 60
- 70
- 80
- 90
100 K
V+ = 3 V
R
L
= 50
X
TALK
OIRR
1M
Temperature (°C)
10 M
100 M
Frequency (Hz)
1G
Switching Time vs. Temperature and Supply Voltage
Insertion Loss, Off-Isolation, Crosstalk vs. Frequency
3.0
250
200
V
T
- Switching Threshold (V)
2.5
Q - Charge Injection (pC)
150
100
50
0
- 50
- 100
- 150
- 200
V+ = 2 V
V+ = 3 V
V+ = 5 V
2.0
1.5
1.0
0.5
0.0
0
1
2
3
4
5
6
7
V+ - Supply Voltage (V)
- 250
0
1
2
3
V
COM
- Analog Voltage (V)
4
5
Switching Threshold vs. Supply Voltage
Charge Injection vs. Analog Voltage
Document Number: 72505
S11-0303-Rev. D, 28-Feb-11
www.vishay.com
5
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
The standard bell on the bicycle looks ordinary. I bought a small 3V horn online. It is very cheap and easy to use. It only needs to be powered and does not need to be driven.The speaker modification ...
When used as a slave IIC, the Clock is 400KHz, the chip is STM8S105K6, and the external 16MHz crystal oscillator can work normally at first, but it dies after a while (randomly). The specific manifest...
[size=5]Reasons for sharing: Students who have only learned the C language of 51 single-chip microcomputers can also quickly develop human-computer interaction interfaces and automatic control systems...
There is no problem with the parallel port, because another friend's board can be connected, but when I connect to mine, I still can't find the CPU in HJTAG....
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
introduction
The emergence of high-performance, low-power embedded CPUs and high-reliability network operating systems has made it possible to implement applications with large amounts of comp...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
1 Introduction
Water resources are the basic conditions for human survival and the lifeline of economic development. The reality shows that due to the global shortage of water resources and th...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Energy Infrastructure?
京公网安备 11010802033920号
EEWORLD
