EEWORLDEEWORLDEEWORLD

Part Number

Search

X4285S8I-4.5A

Description
CPU Supervisor with 128K EEPROM
Categoryaccessories   
File Size405KB,22 Pages
ManufacturerXicon Passive Components
Websitehttp://www.xicor.com
Download Datasheet View All

X4285S8I-4.5A Overview

CPU Supervisor with 128K EEPROM

Preliminary Information
128K
X4283/85
CPU Supervisor with 128K EEPROM
DESCRIPTION
16K x 8 Bit
FEATURES
• Selectable watchdog timer
• Low V
CC
detection and reset assertion
—Four standard reset threshold voltages
—Adjust low V
CC
reset threshold voltage using
special programming sequence
—Reset signal valid to V
CC
= 1V
• Low power CMOS
—<20µA max standby current, watchdog on
—<1µA standby current, watchdog OFF
—3mA active current
• 128Kbits of EEPROM
—64 byte page write mode
—Self-timed write cycle
—5ms write cycle time (typical)
• Built-in inadvertent write protection
—Power-up/power-down protection circuitry
—Protect 0, 1/4, 1/2, all or 64, 128, 256 or 512
bytes of EEPROM array with programmable
Block Lock
protection
• 400kHz 2-wire interface
• 2.7V to 5.5V power supply operation
• Available packages
—8-lead SOIC
—8-lead TSSOP
BLOCK DIAGRAM
Watchdog Transition
Detector
WP
Data
Register
Command
Decode &
Control
Logic
V
CC
Threshold
Reset logic
Block Lock Control
Protect Logic
The X4283/85 combines four popular functions,
Power-on Reset Control, Watchdog Timer, Supply Volt-
age Supervision, and Block Lock protect serial
EEPROM memory in one package. This combination
lowers system cost, reduces board space require-
ments, and increases reliability.
Applying power to the device activates the power on
reset circuit which holds RESET/RESET active for a
period of time. This allows the power supply and oscilla-
tor to stabilize before the processor can execute code.
The Watchdog Timer provides an independent protec-
tion mechanism for microcontrollers. When the micro-
controller fails to restart a timer within a selectable
time out interval, the device activates the RESET/
RESET signal. The user selects the interval from three
preset values. Once selected, the interval does not
change, even after cycling the power.
The device’s low V
CC
detection circuitry protects the
user’s system from low voltage conditions, resetting
the system when V
CC
falls below the set minimum V
CC
trip point. RESET/RESET is asserted until V
CC
returns
to proper operating level and stabilizes. Four industry
Watchdog
Timer Reset
SDA
Status
Register
EEPROM Array
8Kb 4Kb 4Kb
RESET (X4283)
RESET (X4285)
SCL
S0
S1
Reset &
Watchdog
Timebase
V
CC
V
TRIP
+
-
Power on and
Low Voltage
Reset
Generation
REV 1.17 11/27/00
www.xicor.com
Characteristics subject to change without notice.
1 of 22
High-speed PCB design technology (Chinese)
...
至芯科技FPGA大牛 FPGA/CPLD
The posts in this section of NXP are basically untouched! It seems that no one cares. What's going on?
[i=s]This post was last edited by Pinghu Qiuyue on 2014-2-17 12:45[/i] Is this section dead?...
平湖秋月 NXP MCU
I received an email about DHL express delivery, and it felt like a scam. Has anyone encountered this before?
I just received an email from the DHL Information Center in my frequently used school mailbox. It said that my express package could not be delivered due to an unclear address. I need to click on the ...
bobde163 Talking
Ask a small question
The kernel provides basic services for applications. In order to support stream interface drivers, the kernel redirects the application's file I/0 functions to the appropriate stream interface driver ...
MEGANTWJ Embedded System
Two-axis linkage, interpolation algorithm, the movement speed is too slow. Is there any solution?
I use PWM to control two servos. I connect two axes. I tested it and it can walk a circle, but the speed is too slow. Has anyone done this before? Can you give me some advice? I'd be grateful....
flyaqiao Industrial Control Electronics
Wince cannot start in standby mode after modifying the memory size.
The original memory of BSP was 64M, but now it has been changed to 128M. The system can run, but it is just a normal standby function, and it stops when it starts. I hope experts can give me some advi...
holly8301 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2683  1129  245  2639  248  55  23  5  54  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号