Storage Temperature Range .............................-65°C to +165°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(V
DD
= 2.8V to 7V for MAX951/MAX952, V
DD
= 2.4V to 7V for MAX953/MAX954, V
SS
= 0, V
CM COMP
= 0 for the MAX953/MAX954,
V
CM OPAMP
= 0, AMPOUT = (V
DD
+ V
SS
)/2, COMPOUT = low, T
A
= T
MIN
to T
MAX
, typical values are at T
A
= +25°C, unless other-
wise noted.)
PARAMETER
Supply Voltage Range
SYMBOL
V
DD
MAX951/MAX952
MAX953/MAX954
T
A
= +25°C, MAX951/MAX952
MAX951E/MAX952E
Supply Current
(Note 1)
I
S
MAX951M/MAX952M
T
A
= +25°C, MAX953/MAX954
MAX953E/MAX954E
MAX953M/MAX954M
COMPARATOR
T
A
= +25°C
Input Offset Voltage
(Note 2)
V
OS
MAX95_EPA/ESA
MAX95_EUA (μMAX)
MAX95_MJA
T
A
= +25°C
Trip Point
(Note 3)
MAX95_EUA (μMAX)
MAX95_EPA/ESA
MAX95_MJA
Input Leakage Current
(Note 4)
T
A
= +25°C
MAX95_E
MAX95_M
4
17
5
7
0.003
0.003
0.050
5
40
nA
mV
1
3
14
14
6
mV
5
CONDITIONS
T
A
= T
MIN
to T
MAX
T
A
= -10°C to +85°C
MIN
2.8
2.7
2.4
7
TYP
MAX
7.0
7.0
7.0
10
11
13
8
9
11
µA
V
UNITS
www.maximintegrated.com
Maxim Integrated
│
2
MAX951–MAX954
Ultra-Low-Power, Single-Supply
Op Amp + Comparator + Reference
Electrical Characteristics (continued)
(V
DD
= 2.8V to 7V for MAX951/MAX952, V
DD
= 2.4V to 7V for MAX953/MAX954, V
SS
= 0, V
CM COMP
= 0 for the MAX953/MAX954,
V
CM OPAMP
= 0, AMPOUT = (V
DD
+ V
SS
)/2, COMPOUT = low, T
A
= T
MIN
to T
MAX
, typical values are at T
A
= +25°C, unless other-
wise noted.)
PARAMETER
Common-Mode Input
Range
Common-Mode Rejection
Ratio
Power-Supply Rejection
Ratio
Response Time
Output High Voltage
Output Low Voltage
REFERENCE
Reference Voltage
(Note 5)
MAX95_EPA/ESA
V
REF
MAX95_EUA (μMAX)
MAX95_MJA
I
OUT
= ±20μA, T
A
= +25°C
Load Regulation
Voltage Noise
OP AMP
T
A
= +25°C
Input Offset Voltage
V
OS
MAX95_EPA/ESA
MAX95_EUA (μMAX)
MAX95_MJA
T
A
= +25°C
Input Bias Current
I
B
MAX95_E
MAX95_M
Large-Signal Gain
(No Load)
A
VOL
AMPOUT = 0.5V to
4.5V, V
DD
- V
SS
= 5V
AMPOUT = 0.5V to
4.5V, V
DD
- V
SS
= 5V
T
A
= +25°C
MAX95_E
MAX95_M
T
A
= +25°C
MAX95_E
MAX95_M
100
50
10
40
25
5
20
125
kHz
150
V/mV
0.003
0.003
0.003
1000
V/mV
1
3
4
5
5
0.050
5
40
nA
mV
e
n
I
OUT
= ±6μA, MAX95_E
I
OUT
= ±3μA, MAX95_M
0.1Hz to 10Hz
16
1.176
1.130
1.164
1.200
1.200
1.200
0.1
1.5
1.5
μV
P-P
%
1.224
1.270
1.236
V
SYMBOL
CMVR
CMRR
PSRR
t
pd
V
OH
V
OL
V
SS
to (V
DD
- 1.6V), MAX953/MAX954
MAX951/MAX952, V
DD
= 2.8V to 7V
MAX953/MAX954, V
DD
= 2.4V to 7V
C
L
= 100pF, T
A
= +25°C,
V
DD
- V
SS
= 5V
I
SOURCE
= 2mA
I
SINK
= 1.8mA
V
OD
= 10mV
V
OD
= 100mV
V
DD
- 0.4V
V
SS
+ 0.4V
CONDITIONS
MIN
V
SS
0.1
0.05
0.05
22
4
TYP
MAX
V
DD
-1.6V
1
1
1
UNITS
V
mV/V
mV/V
µs
V
V
Large-Signal Gain
(100kΩ Load to V
SS
)
Gain Bandwidth
A
VOL
GBW
A
V
= 1V/V, MAX951/MAX953, V
DD
- V
SS
= 5V
A
V
= 10V/V, MAX952/MAX954, V
DD
- V
SS
= 5V
www.maximintegrated.com
Maxim Integrated
│
3
MAX951–MAX954
Ultra-Low-Power, Single-Supply
Op Amp + Comparator + Reference
Electrical Characteristics (continued)
(V
DD
= 2.8V to 7V for MAX951/MAX952, V
DD
= 2.4V to 7V for MAX953/MAX954, V
SS
= 0, V
CM COMP
= 0 for the MAX953/MAX954,
V
CM OPAMP
= 0, AMPOUT = (V
DD
+ V
SS
)/2, COMPOUT = low, T
A
= T
MIN
to T
MAX
, typical values are at T
A
= +25°C, unless other-
wise noted.)
PARAMETER
Slew Rate
Common-Mode Input
Range
Common-Mode Rejection
Ratio
Power-Supply Rejection
Ratio
Input Noise Voltage
Output High Voltage
Output Low Voltage
SYMBOL
SR
CMVR
CMRR
PSRR
e
n
V
OH
V
OL
I
SRC
V
CM OPAMP
= V
SS
to (V
DD
- 1.6V)
V
DD
= 2.8V to 7V, MAX951/MAX952
V
DD
= 2.4V to 7V, MAX953/MAX954
f
o
= 1kHz
f
o
= 0.1Hz to 10Hz
R
L
= 100kΩ to V
SS
R
L
= 100kΩ to V
SS
T
A
= +25°C
Output Source Current
T
A
= +25°C, V
DD
- V
SS
= 5V
MAX95_E
MAX95_M
T
A
= +25°C
Output Sink Current
I
SNK
T
A
= +25°C, V
DD
- V
SS
= 5V
MAX95_E
MAX95_M
70
300
60
40
70
200
50
30
570
µA
820
µA
CONDITIONS
A
V
= 1V/V, MAX951/MAX953, V
DD
- V
SS
= 5V
A
V
= 10V/V, MAX952/MAX954, V
DD
- V
SS
= 5V
V
SS
0.03
0.07
0.07
80
1.2
V
DD
- 500mV
V
SS
+ 50mV
MIN
TYP
12.5
66
V
DD
- 1.6
1
1.0
1.0
MAX
UNITS
V/ms
V
mV/V
mV/V
nV√Hz
μV
P-P
V
V
Note 1:
Supply current is tested with COMPIN+ = (REF - 100mV) for MAX951/MAX952, and COMPIN+ = 0 for MAX953/MAX954.
Note 2:
Input Offset Voltage is defined as the center of the input-referred hysteresis. VCM COMP
= REF for MAX951/MAX952, and
VCM COMP = 0 for MAX953/MAX954.
Note 3:
Trip Point is defined as the differential input voltage required to make the comparator output change. The difference
between upper and lower trip points is equal to the width of the input-referred hysteresis. VCM COMP
= REF for MAX951/
MAX952, and VCM COMP = 0 for MAX953/MAX954.
Note 4:
For MAX951/MAX952, input leakage current is measured for COMPIN- at the reference voltage. For MAX953/MAX954,
input leakage current is measured for both COMPIN+ and COMPIN- at VSS.
Note 5:
Reference voltage is measured with respect to V
SS
. Contact factory for availability of a 3% accurate reference voltage in
Salt spray test chamber is mainly suitable for salt spray corrosion test of parts, electronic hardware components, protective layer of metal materials and industrial products. Artificial simulated sal...
I applied for a development kit today. The chip used is the MSP430G2 series. I would like to ask, what does the G series mean? For example, the F series is the flash type....
I have been looking for a solution to this problem for a long time. I hope someone can send me a copy of the MSN: guitar_1314@hotmail.com QQ: 22174907...
The FPGA integrated development environment provided by Anlu has a grand name: Tang Dynasty, or TD for short. Its functions are similar to those of Altera's Quartus II and Xilinx's ISE.
After instal...
[align=left][color=#000000][font=Times New Roman]2012-09-28 [/font]I received the board yesterday. I plugged it into the computer today. I need to install the [font=Times New Roman]FT2232[/font] drive...
In recent years, with the increasing demand for manufacturing and automated production management, industrial barcode scanners have gradually become an indispensable part of the industrial manufact...[Details]
Is electromagnetic radiation from electric vehicles harmful to the human body? Recently, the issue of electromagnetic radiation from electric vehicles has garnered widespread attention. However, pu...[Details]
As more and more consumers purchase new energy vehicles, the safety of electric vehicles has become a major concern. This has been particularly prominent following a series of electric vehicle fire...[Details]
When we travel in cities, we all find that electric vehicles have many advantages. As a means of transportation, they can also fulfill their mission well. Now, more and more residential communities...[Details]
With the rapid adoption of smart electric vehicles, automotive chips are evolving from auxiliary control units to the foundation of the entire vehicle's intelligence. Their applications extend from...[Details]
Recently, South Korean robotics giant WIRobotics launched its first general-purpose humanoid robot, ALLEX, at the Robotics Innovation Center (RIH) at the Korea University of Science and Technology....[Details]
introduction
The concept of the smart home is gradually developing and gaining market acceptance. We believe its ultimate form lies in the interconnection of all home appliances through open i...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
Electric vehicles are powered by electricity, and charging is a device that supplements the vehicle's energy source. It is common to need to recharge the vehicle when driving. But can you charge th...[Details]
Methods of DC motor speed regulation:
1. The voltage regulator can be used to change the input voltage and speed directly, which is often used for large kilowatt-level motors.
2. Thyristo...[Details]
For today's new energy vehicles, they have different configurations from fuel vehicles, and some configurations have also become a selling point for manufacturers. Compared with traditional vehicle...[Details]
Definitions of VR
, AR, and MR:
What is Virtual Reality?
Virtual Reality (VR), also known as "spiritual realm" or "illusion," is a high-tech technology that has emerged in recent ye...[Details]
Most cameras on the market use chips manufactured by Japanese companies like Sony, Sharp, Panasonic, and LG. South Korea now has the capability to produce chips, but the quality is somewhat inferio...[Details]
Hair dryer structure and working principle: It is mainly used for drying and shaping hair, but it can also be used for local drying, heating and treatment in laboratories, physiotherapy rooms, ind...[Details]
Cadence and NVIDIA Collaborate to Revolutionize Power Analysis Technology, Accelerating Development of Billion-Gate AI Designs
Cadence's new Palladium Dynamic Power Analysis applicat...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
