Note: The IF_S(D)-W25 Series also available in our company. *Designing.
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development
center, Science Ave., Guangzhou Science City,
Luogang district, Guangzhou,P.R.China.
Tel: 86-20-28203030
Fax:86-20-28203068
Http://www.mornsun-power.com
ISOLATION SPECIFICATIONS
Item
Isolation voltage
Isolation resistance
Test condition
Tested for 1 minute
Test at 500VDC
Min
3000
1000
Typ
Max
Units
VDC
MΩ
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
IF_S(D)-1W
A/2-2011
Page 1 of 3
OUTPUT SPECIFICATIONS
Item
Output power
Line regulation
Load regulation
Output voltage accuracy
Temperature drift
Output ripple*
Output noise*
Switching frequency
For Vin change of
±5%
10% to 100% full load
100% full load
100% full load
20MHz bandwidth
20MHz bandwidth
Full load, nominal input voltage
10
50
100
Test condition
Min
0.1
Typ
Max
1
±0.25
±1
±3
0.03
20
100
KHz
%/°C
mVp-p
%
Units
W
TYPICAL CHARECTERISTICS
Temperature Derating Graph
*
Test ripple and noise by
“parallel
cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Operating Temp.(
C
)
COMMON SPECIFICATIONS
Item
Storage humidity range
No-load power consumption
Storage humidity range
Operating temp. range
Temp. rise at full load
Lead temperature
Short circuit protection
Cooling
Case material
MTBF
3500
1.5mm from case for 10 seconds
IFXX05S/D-1W*
Others
-55
-40
15
10
125
85
25
300
1
Continuous
Free air convection
Plastic (UL94-V0)
K hours
S
°C
Test condition
Min
Typ Max
95
Units
%
*
Supply voltage must be discontinued at the end of short circuit duration.
APPLICATION NOTE
①
Requirement On Output Load
To ensure this module can operate efficiently and reliably, a minimum load is specified for this
kind of DC/DC converter in addition to a maximum load (namely full load). During operation,
make sure the specified range of input voltage is not exceeded, the minimum output load
could
not be less than 10% of the full load.
If the actual output power is very small, please connect
a resistor with proper resistance at the output end in parallel to increase the load, or use our
company’s products with a lower rated output power (IF_S(D)
–W25
Series).
RECOMMENDED CIRCUIT
L
L
Vin
C
+Vo
DC DC
(Figure 1)
C
GND
0V
EXTERNAL CAPACITOR TABLE (TABLE 1)
②
Filtering
In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to
the DC/DC output end and input end to reduce the noise and ripple. However, the capacitance
of the output filter capacitor must proper. If the capacitance is too big, a startup problem might
arise. For every channel of output, providing the safe and reliable operation is ensured, the
greatest capacitance of its filter capacitor refer to (Table 1).
To get an extremely low ripple, an
“LC”
filtering network may be connected to the input and
output ends of the DC/DC converter, which may produce a more significant filtering effect. It
should also be noted that the inductance and the frequency of the
“LC”
filtering network should
be staggered with the DC/DC frequency to avoid mutual interference (Figure 1).
Vin
(VDC)
5
12
24
-
Cin
(
μF
)
4.7
2.2
1
-
Vout
(VDC)
5
9
12
15
Cout
(
μF
)
10
4.7
2.2
1
It’s not recommended to connect any external capacitor
in the application field with less than 0.5 watt output.
③
Overload Protection
Under normal operating conditions, the output circuit of these products has no protection
against over-current .The simplest method is to connect a self-recovery fuse in series at the
input end or add a circuit breaker to the circuit.
④
When the environment temperature is higher than 71°C, the product output power
should be less then 60% of the rated power.
⑤
No parallel connection or plug and play.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
IF_S(D)-1W
A/2-2011
Page 2 of 3
OUTLINE DIMENSIONS& RECOMMENDED FOOTPRINT
MECHANICAL DIMENSIONS
IF_S-1W Series SIP Package
RECOMMENDED FOOTPRINT
12.70
[0.500]
7.62
[0.300]
∅
1.00[
∅
0.039]
1 2
4
6
6.00[0.236]
∅
1.00[
∅
0.039]
15 .70
[0. 618]
7.62
[0.300]
10.00
[0.394]
0.50[0.020]
19.60[0.772]
(Front View)
10.00
[0.394]
2.54[0.100]
2.18[0.086]
0.90 [0.035]
7.62
[0.300]
12.70
[0.500]
4.10[0.161]
2.18[0.086]
2.54[0.100]
19.60[0.772]
Note
:
Grid:2.54*2.54mm
.
TUBE OUTLINE DIMENSIONS
1 2
0.90 [0.035]
(Bottom View)
4
6
9.40
[0.370]
0.30[0.012]
6.00 [0.236]
12.20
[0.480]
Note:
Unit:mm[inch]
Pin section tolerances:±0.10mm[±0.004inch]
General tolerances:±0.25mm[±0.010inch]
FOOTPRINT DETAILS
Pin
1
2
4
6
Function
Vin
GND
0V
+Vo
Note:
4.70[0.185]
Unit :mm[inch]
General tolerances:
±0.50mm[±0.020inch]
L=530mm[20.866inch] Devices per tube quantity: 25pcs
L=220mm[8.661inch] Devices per tube quantity: 10pcs
Short tube inner packaging dimensions: L*W*H=255*170*80mm
Short tube outer packaging dimensions: L*W*H=375*280*270mm
Long tube inner packaging dimensions: L*W*H=580*200*100mm
Long tube outer packaging dimensions(with two inner packaging boxes):
L*W*H=600*215*220mm
Long tube outer packaging dimensions(with three inner packaging boxes):
L*W*H=600*215*325mm
MECHANICAL DIMENSIONS
IF_D-1W Series DIP package
RECOMMENDED FOOTPRINT
0. 50[0.020]
（
Front View
）
7.00
[0.276]
20.00[0.787]
12.70
[0.500]
5.08[0.200]
14
4.10[0 .161]
16.70
[0.657]
0.50[0.020]
11
9
7
15.24[0.600]
20.00[0.787]
15.24[0.600]
1
7
（
Bottom View
）
14
11
9
7.62
[0.300]
10.00
[0.394]
0.30[0.012]
TUBE OUTLINE DIMENSIONS
12.00
[0.472]
9.60
[0.37 8]
0.50[0.020]
7.62
[0.300]
12.70
[0.500]
Note:
Unit:m m[inch]
Pin section tolerances:±0.10mm [±0.004inch]
General tolerances:±0.25m m[±0.010inch]
FOOTPRINT DETAILS
Pin
1
7
9
11
14
Function
GND
NC
+Vo
0V
Vin
NC
:
No connection
Note:
5.30[0.209]
Unit :mm[inch]
General tolerances:
±0.50mm[±0.020inch]
L=530mm[20.866inch] Devices per tube quantity: 25pcs
L=220mm[8.661inch] Devices per tube quantity: 10pcs
Short tube inner packaging dimensions: L*W*H=255*170*80mm
Short tube outer packaging dimensions: L*W*H=375*280*270mm
Long tube inner packaging dimensions: L*W*H=580*200*100mm
Long tube outer packaging dimensions(with two inner packaging boxes):
L*W*H=600*215*220mm
Long tube outer packaging dimensions(with three inner packaging boxes):
L*W*H=600*215*325mm
Note:
1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
2. See below recommended circuits for more details.
3. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life of product.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
There are many manufacturers of power electronic products (including various power supplies, frequency converters, power factor and harmonic compensation devices) in my country, but most of them do no...
The voltage and direction of AC change with time. After 220VAC rectification, the voltage only changes in magnitude but not direction. So it should not be AC, right? If I add a capacitor to step down ...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:56[/i] SMSC, a leading developer of Smart Mixed-Signal Connectivity? solutions, today announced ViewSpan? USB 3.0 remote graphics tec...
[i=s]This post was last edited by dontium on 2015-1-23 11:24[/i]TI's official website specifically lists transimpedance amplifiers in the column of special operational amplifiers. Transimpedance ampli...
The rotary encoder is a photoelectric rotary measuring device that directly converts the measured angular displacement into a digital signal (high-speed pulse signal). Therefore, the output pulse sign...
The Sino-US trade war has already started. Trump's series of actions have had a negative impact on the global economy, such as increasing tariffs on Chinese companies and restricting domestic compa...[Details]
In the past few days, the Chinese display panel giant
BOE
has been flooded with articles supported by Liu Shuwei. Let's follow the embedded editor to learn about the relevant content.
...[Details]
In the actual project development process, hardware circuits often need to be modified, and the modified parts need to modify the driver. Thinking about the coming and going of such requirements is t...[Details]
Unique device identifiers are suitable for: ● Used as a serial number (e.g. USB string serial number or other terminal applications) ● Use the unique ID as a security key when used in conjunction wit...[Details]
In simple terms, high-end chips solve many complex problems, mid-range chips solve a single complex problem, and low-end chips solve a simple problem. Let's learn more about the relevant content wi...[Details]
LAN8720 test code arrangement 1. Modified based on two projects, namely "Experiment 55 Network Communication Experiment" of Zhengdian Atom ATK and "STSW-STM32070" routine of ST official The hardware ...[Details]
1. Basic Concepts of LCD/LCM The structure of Liquid Crystal Display (LCD) is to place liquid crystals between two parallel pieces of glass. There are many vertical and horizontal fine wires between...[Details]
The F1 racetrack is roaring with engines, and a fierce F1 race is about to begin. I am not a fan of racing cars, and I have nothing to do with this world, but
I spent a special day here
because...[Details]
This small program is still the use of timer, which is relatively simple. The specific parts are noted in the comments, please refer to the comments. /*********************************************...[Details]
*This article is based on the author's report at the "Embedded System Association Theme Discussion (Total 22nd) - Current Situation and Development Prospects of Internet of Things Operating Systems...[Details]
In January, Android 7.0 Marshmallow surpassed Lollipop three years ago to become the second most used Android version in the world. According to
the latest data from
Google
, a snapshot of d...[Details]
On Sunday, the South Australian government unveiled plans to build the world's largest virtual power plant, which will connect at least 50,000 homes over four years and have a capacity ...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
In order to strengthen the traceability management of recycling and utilization of power batteries for new energy vehicles, and to standardize and guide all relevant parties to fulfill their tracea...[Details]
Use common anode digital tube and independent keyboard to connect P1 and P2 ports of single chip to realize answering machine The procedure is as follows: #include reg52.h void delay(unsigned char n)...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
