AZ696
10 AMP SUBMINIATURE
POWER RELAY
FEATURES
•
•
•
•
•
•
•
High sensitivity, 110 mW pickup
Dielectric strength 4000 Vrms
Isolation spacing greater than 8 mm
Proof tracking index (PTI/CTI) 250
10 Amp switching capability
Epoxy sealed version available
Reinforced insulation, EN 60730-1 (VDE 0631, part 1)
EN 60335-1 (VDE 0700, part 1)
•
UL, CUR file E44211,
•
VDE file 117422 ÜG
CONTACTS
Arrangement
Ratings
SPDT (1 Form C)
SPST (1 Form A and 1 Form B)
Resistive load:
Max. switched power: 240 W or 2500 VA
Max. switched current: 10 A
Max. switched voltage: 240 VDC* or 440 VAC
*
Note: If switching voltage is greater than 30 VDC,
GENERAL DATA
Life Expectancy
Mechanical
Electrical
Operate Time (typical)
Release Time (typical)
Minimum operations
1 X 10
7
1 X 10
5
at 8 A 250 VAC Res.
10 ms at nominal coil voltage
5 ms at nominal coil voltage
(with no coil suppression)
special precautions must be taken.
Please contact the factory.
Dielectric Strength
4000 Vrms coil to contact
(at sea level for 1 min.)
1000 Vrms between open contacts
Insulation
Resistance
Insulation
(according to
DIN VDE 0110,
IEC 60664-1)
Dropout
Ambient Temperature
Operating
Storage
Vibration
1000 megohms min. at 20°C, 500 VDC,
50% RH
C250
Overvoltage category: III
Pollution degree: 3
Nominal voltage: 250 VAC
Greater than 10% of nominal coil voltage
At nominal coil voltage
-40°C (-40°F) to 85°C (185°F)
-40°C (-40°F) to 105°C (221°F)
0.062" (1.5 mm) DA at 10–55 Hz
20 g
P.B.T. polyester, UL94 V-0
Tinned copper alloy, P.C.
270°C (518°F)
5 seconds
80°C (176°F)
30 seconds
14 grams
50 per plastic tray / 1500 per carton box
Rated Load
UL, CUR
10 A at 30 VDC resistive
10 A at 250 VAC general use
1
/
4
HP 120 VAC
1
/
2
HP 250 VAC
B 300 pilot duty
8 A at 250 VAC resistive, 100k cycles [1]
10 A at 250 VAC resistive, 50k cycles [2]
Silver cadmium oxide [1] or silver tin oxide [2]
< 30 milliohms initially
VDE
Material
Resistance
COIL
Power
At Pickup Voltage
(typical)
Max. Continuous
Dissipation
Temperature Rise
Temperature
110 mW
140 mW (48 VDC coil)
1.5 W at 20°C (68°F) ambient
20°C (36°F) at nominal coil voltage
Max. 110°C (230°F)
Shock
Enclosure
Terminals
Max. Solder Temp.
Max. Solder Time
Max. Solvent Temp.
Max. Immersion Time
Weight
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
4. It’s recommended to remove vent nipple on sealed versions to
expand life expectancy when switching higher loads.
Packing unit in pcs
ZETTLER
electronics GmbH
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
office@ZETTLERelectronics.com
www.ZETTLERelectronics.com
2004-11-25
Junkersstrasse 3, D-82178 Puchheim, Germany
AZ696
RELAY ORDERING DATA
COIL SPECIFICATIONS
Nominal Coil
VDC
5
6
9
12
18
24
48
Must Operate
VDC
3.5
4.2
6.3
8.4
12.6
16.8
33.6
Max. Continuous
VDC
12.0
14.5
22.0
29.5
44.0
54.0
102.0
Coil Resistance
Ohm ± 10%
110
160
360
660
1,500
2,200
8,000
ORDER NUMBER*
1 Form A
(SPST-NO)
AZ696–1A–5D
AZ696–1A–6D
AZ696–1A–9D
AZ696–1A–12D
AZ696–1A–18D
AZ696–1A–24D
AZ696–1A–48D
1 Form C
(SPDT)
AZ696–1C–5D
AZ696–1C–6D
AZ696–1C–9D
AZ696–1C–12D
AZ696–1C–18D
AZ696–1C–24D
AZ696–1C–48D
* Substitute “1B” in place of “1A” for 1 Form B contact. Add suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts.
Add suffix “E” at the end of order number for sealed version.
MECHANICAL DATA
Coil Temperature Rise
1 FORM C
1 FORM A and 1FORM B
100
90
1.18
(30)
.394
(10)
1.10
(28)
.394
(10)
80
Coil Temperature Rise °C
70
60
50
40
30
20
10
0
60
80
100
120
140
10 A
0A
FORM C
.618
(15.7)
.638
(16.2)
.618
(15.7)
.638
(16.2)
.138 (3.5)
.138 (3.5)
.024 x .035
(0.6 x 0.9)
.024 x .039
(0.6 x 1)
.024 x .035
(0.6 x 0.9)
.024 x .039
(0.6 x 1)
160
180
200
220
Percent of Nominal Coil Voltage at 20°C
PC BOARD LAYOUT
1 FORM C
2 x
ø
.051
(
ø
1.3)
.299
(7.6.)
3 x
ø
.059
(
ø
1.5)
.126
(3.2)
WIRING DIAGRAMS
1
1 FORM C
4
Maximum Switching Capacity
10.0
2
3
5
.122
(3.1)
.748
(19.)
.126
(3.2)
9.0
8.0
7.0
6.0
5.0
4.0
3.0
DC Resistive
Load
1 FORM A
1
3
2.0
1 FORM A and 1 FORM B
2 x
ø
.051
(
ø
1.3)
.299
(7.6.)
2 x
ø
.059
(
ø
1.5)
2
4
CURRENT
AC Resistive
Load
1.0
.9
.8
.7
.6
.5
1 FORM B
1
3
.4
.3
.2
10
100
.197
(5)
2
4
Viewed toward terminals
Viewed toward terminals
VOLTAGE
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
ZETTLER
electronics GmbH
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
office@ZETTLERelectronics.com
www.ZETTLERelectronics.com
2004-11-25
Junkersstrasse 3, D-82178 Puchheim, Germany
1000
.122
(3.1)
.748
(19)
.1
20
30
40
50
60
70
80
90
200
300
400
500
600
700
800
900
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
