• Apply 4.15 V – 5.25 V for 5 V version or 3.00 V – 3.60 V for 3 V version to the Vcc pin. Apply 0 V to the
Vss pin.
• This controls the MCU operating mode. Connect this pin to Vss. If connecting this pin to Vcc, the
internal ROM is inhibited. In the flash memory version this pin functions as a V
PP
power supply input pin.
• These pins are the power supply inputs for analog circuitry.
• Reset input pin for active “L.”
• Connect a ceramic resonator or a quartz-crystal oscillator between the X
IN
and X
OUT
pins to set the
oscillation frequency.
• If an external clock is used, connect the clock source to the X
IN
pin and leave the X
OUT
pin open.
• Loop filter for the frequency synthesizer.
• Power supply input pin for 3.3 V USB line driver.
• USB D+ voltage signal port. Connect a 27 to 33
Ω
(recommended) resistor in series.
• USB D- voltage signal port. Connect a 27 to 33
Ω
(recommended) resistor in series.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually programmed as either input or output.
• When connecting an external memory, these function as the address bus.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually programmed as either input or output.
• When connecting an external memory, these function as the address bus.
• 8-bit I/O port.
• CMOS compatible input level or VIHL input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When connecting an external memory, these function as
the data bus.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When connecting an external memory, these function as
the control bus.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When connecting an external memory, these function as
the control bus.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When enabling the Master CPU bus interface function,
CMOS or TTL input level can be selected as an input.
• Key-on wake-up interrupt input pin
Function
P1
0
/AB
8
–
P1
7
/AB
15
I/O port P1
P2
0
/DB
0
–
P2
7
/DB
7
I/O port P2
P3
0
/RDY,
I/O port P3
P3
1
, P3
2
,
(See Remarks.)
P3
3
/DMA
OUT
,
P3
4
/φ
OUT
,
P3
5
/SYNC
OUT
,
P3
6
/WR,
P3
7
/RD
P4
0
/EDMA,
I/O port P4
P4
1
/INT
0
,
P4
2
/INT
1
,
P4
3
/CNTR
0
,
P4
4
/CNTR
1
P5
0
/X
CIN
,
P5
1
/T
OUT
/
X
COUT
,
P5
2
/OBF
0
,
P5
3
/IBF
0
,
P5
4
/S
0
,
P5
5
/A
0
,
P5
6
/R(E),
P5
7
/W(R/W)
I/O port P5
• External memory control pin
• External memory control pin
• External interrupt pin
• Timer X, Timer Y pin
• Sub-clock generating input pin
• Timers 1, 2 pulse output pins
• Sub-clock generating output pin
• Master CPU bus interface pin
4
P
.
ion
cat
cifi ct to
e
l sp ubje
s
fina
t a ts are
o
is n limi
his etric
e: T
otic param
N
e
Somnge.
a
ch
REL
IMIN
ARY
MITSUBISHI MICROCOMPUTERS
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 2 Pin description (2)
Pin
P6
0
/DQ
0
–
P6
7
/DQ
7
Name
I/O port P6
Function
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When enabling the bus interface function, CMOS or TTL
input level can be selected as its input.
• 5-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
Function except a port function
• Master CPU bus interface pin
P7
0
/SOF,
P7
1
/HOLD,
P7
2
/S
1
,
P7
3
/IBF
1
/
HLDA,
P7
4
/OBF
1
P8
0
/UTXD
2
/
SRDY,
P8
1
/URXD
2
/
SCLK,
P8
2
/CTS
2
/
SRXD,
P8
3
/RTS
2
/
STXD,
P8
4
/UTXD
1
,
P8
5
/URXD
1
,
P8
6
/CTS
1
,
P8
7
/RTS
1
I/O port P7
• USB function pin
• Master CPU bus interface pin
I/O port P8
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually pro-
grammed as either input or output.
• Serial I/O pin
• UART2 pin
• UART1 pin
Remarks
•DMA
OUT
pin
If externally detecting the timing of DMA execution, use the signal from this pin. It is “H” level during DMA transferring. This signal is valid in the memory expansion
and microprocessor modes.
•SYNC
OUT
pin
If externally detecting the timing of OP code fetch, use the signal from this pin. This signal is valid in the memory expansion and microprocessor modes.
Due to the limited instruments at hand, I plan to use a differential probe to measure the voltage across the resistor as shown in the figure below, so as to calculate the laser current. There are two ...
Hello everyone. My development platform is S3C2410+WINCE5.0, and I want to make the WINCE device be recognized as a USB disk when it is connected to the PC via a USB cable. I changed the relevant regi...
When placing a component in Allegro, it says W- (SPMHUT-48): Scaled value has been rounded off. Why can't the component be placed? I searched online and found that some people said the board frame is ...
There is a circuit that can automatically shut off the power if not used for a long time. How is it controlled? Its main chip is EC51925A. This chip should be controlled by a certain pin, but I don't ...
As the industry's hardware interconnection structure trend changes from parallel bus mode to high-speed serial mode, the hard disk interface has transitioned from ATA parallel bus signal mode to SATA ...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
