• Apply 4.15 V – 5.25 V for 5 V version or 3.00 V – 3.60 V for 3 V version to the Vcc pin. Apply 0 V to the
Vss pin.
• This controls the MCU operating mode. Connect this pin to Vss. If connecting this pin to Vcc, the
internal ROM is inhibited. In the flash memory version this pin functions as a V
PP
power supply input pin.
• These pins are the power supply inputs for analog circuitry.
• Reset input pin for active “L.”
• Connect a ceramic resonator or a quartz-crystal oscillator between the X
IN
and X
OUT
pins to set the
oscillation frequency.
• If an external clock is used, connect the clock source to the X
IN
pin and leave the X
OUT
pin open.
• Loop filter for the frequency synthesizer.
• Power supply input pin for 3.3 V USB line driver.
• USB D+ voltage signal port. Connect a 27 to 33
Ω
(recommended) resistor in series.
• USB D- voltage signal port. Connect a 27 to 33
Ω
(recommended) resistor in series.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually programmed as either input or output.
• When connecting an external memory, these function as the address bus.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually programmed as either input or output.
• When connecting an external memory, these function as the address bus.
• 8-bit I/O port.
• CMOS compatible input level or VIHL input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When connecting an external memory, these function as
the data bus.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When connecting an external memory, these function as
the control bus.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When connecting an external memory, these function as
the control bus.
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When enabling the Master CPU bus interface function,
CMOS or TTL input level can be selected as an input.
• Key-on wake-up interrupt input pin
Function
P1
0
/AB
8
–
P1
7
/AB
15
I/O port P1
P2
0
/DB
0
–
P2
7
/DB
7
I/O port P2
P3
0
/RDY,
I/O port P3
P3
1
, P3
2
,
(See Remarks.)
P3
3
/DMA
OUT
,
P3
4
/φ
OUT
,
P3
5
/SYNC
OUT
,
P3
6
/WR,
P3
7
/RD
P4
0
/EDMA,
I/O port P4
P4
1
/INT
0
,
P4
2
/INT
1
,
P4
3
/CNTR
0
,
P4
4
/CNTR
1
P5
0
/X
CIN
,
P5
1
/T
OUT
/
X
COUT
,
P5
2
/OBF
0
,
P5
3
/IBF
0
,
P5
4
/S
0
,
P5
5
/A
0
,
P5
6
/R(E),
P5
7
/W(R/W)
I/O port P5
• External memory control pin
• External memory control pin
• External interrupt pin
• Timer X, Timer Y pin
• Sub-clock generating input pin
• Timers 1, 2 pulse output pins
• Sub-clock generating output pin
• Master CPU bus interface pin
4
P
.
ion
cat
cifi ct to
e
l sp ubje
s
fina
t a ts are
o
is n limi
his etric
e: T
otic param
N
e
Somnge.
a
ch
REL
IMIN
ARY
MITSUBISHI MICROCOMPUTERS
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 2 Pin description (2)
Pin
P6
0
/DQ
0
–
P6
7
/DQ
7
Name
I/O port P6
Function
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
• When enabling the bus interface function, CMOS or TTL
input level can be selected as its input.
• 5-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually
programmed as either input or output.
Function except a port function
• Master CPU bus interface pin
P7
0
/SOF,
P7
1
/HOLD,
P7
2
/S
1
,
P7
3
/IBF
1
/
HLDA,
P7
4
/OBF
1
P8
0
/UTXD
2
/
SRDY,
P8
1
/URXD
2
/
SCLK,
P8
2
/CTS
2
/
SRXD,
P8
3
/RTS
2
/
STXD,
P8
4
/UTXD
1
,
P8
5
/URXD
1
,
P8
6
/CTS
1
,
P8
7
/RTS
1
I/O port P7
• USB function pin
• Master CPU bus interface pin
I/O port P8
• 8-bit I/O port.
• CMOS compatible input level.
• CMOS 3-state output structure.
• I/O direction register allows each pin to be individually pro-
grammed as either input or output.
• Serial I/O pin
• UART2 pin
• UART1 pin
Remarks
•DMA
OUT
pin
If externally detecting the timing of DMA execution, use the signal from this pin. It is “H” level during DMA transferring. This signal is valid in the memory expansion
and microprocessor modes.
•SYNC
OUT
pin
If externally detecting the timing of OP code fetch, use the signal from this pin. This signal is valid in the memory expansion and microprocessor modes.
The original night vision camera of Audi is broken, and I am going to buy a thermal imaging night vision camera on the market. How can I connect the CVBS and LVDS video signals to the meter screen of ...
[url=http://www.askcad.com/bbs/thread-9157-1-1.html]http://www.askcad.com/bbs/thread-9157-1-1.html[/url] This is a compilation post from a CAD forum, which mainly compiles a netizen's own experience i...
The image output area is adjusted from 800*480 to 640*480. How to clean the extra areas on both sides? Otherwise, there will be some residual images!...
In some solutions, CPU A0 is connected to FLASH A0, and in some solutions, CPU A1 is connected to FLASH A0, and in both cases, FLASH works in 16-bit mode. Can anyone explain the reason?...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Investment in
the
medical device
industry has been on the rise in recent years. In the past two years, venture capital for medical devices has almost doubled, reaching $4 billion in 2007. Fr...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
Recently, news came from the certification department that the photovoltaic grid-connected inverter of Samil New Energy Co., Ltd. (hereinafter referred to as "Samil New Energy") has once again obta...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
Key Points
1. Now, in addition to high-end smartphones and tablets, users also expect to use touch screens in other applications, and they are gradually appearing in cars and instruments.
...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
Electric bicycles have long been a means of transportation for lower-income groups due to their affordability. The largest concentrated expense in the use of electric vehicles is the cost of replac...[Details]
The production process of lithium batteries does not mention the previous processes such as material preparation, winding, liquid injection, and packaging, but only talks about the final formation ...[Details]
Mobile phones, MP3s, tablet computers, laptops, digital cameras, handheld game consoles, navigation devices, etc., all these mobile devices are powered by mobile batteries, and the battery life is ...[Details]
In recent years, with the increasing maturity of LED technology, LED light sources have been increasingly widely used due to their advantages of using low-voltage power supply, low energy consumpti...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
