Power supply. Connect both pins to same voltage (either 3.3 V or 5 V).
Connect to ground.
Select input 0. See table above.
Select input 1. See table above.
Clock Output 7. See table above.
Clock Output 8. See table above. Normally use this clock as feedback.
Feedback Input. Connect to CLK8 under normal operations.
Key: I = Input; O = output; P = power supply connection.
External Components
The ICS671-01 requires a minimum number of external components for proper operation. Decoupling
capacitors of 0.01µF should be connected between VDD and GND on pins 4 and 5, and VDD and GND
on pins 13 and 12, as close to the device as possible. A series termination resistor of 33
Ω
may be used close
to each clock output pin to reduce reflections.
2
Revision 051700
Printed 11/15/00
Integrated Circuit Systems, Inc.• 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com
MDS 671-01 B
ICS671-01
Zero Delay, Low Skew Buffer and Multipler
Electrical Specifications
Parameter
Supply voltage, VDD
Inputs and Clock Outputs
Electrostatic Discharge
Ambient Operating Temperature
Soldering Temperature
Junction temperature
Storage temperature
Operating Voltage, VDD
Input High Voltage, VIH, CLKIN pin only
Input Low Voltage, VIL, CLKIN pin only
Input High Voltage, VIH
Input Low Voltage, VIL
Output High Voltage, VOH
Output Low Voltage, VOL
Output High Voltage, VOH, CMOS level
Operating Suppl Current, IDD (Note 2)
Operating Suppl Current, IDD (Note 3)
Short Circuit Current
Input Capacitance
Conditions
Referenced to GND
Referenced to GND
MIL-STD-883
Max of 10 seconds
-65
3.13
VDD/2+1
2
0.8
IOH=-25mA
IOL=25mA
IOH=-8mA
No Load, S1=1, S0=0
No Load, S1=1, S0=0
Each output
S0, S1, FBIN
2.4
0.4
VDD-0.4
25
74
±50
7
Minimum
-0.5
-0.5
2000
0
Typical
Maximum
7
VDD+0.5
70
260
150
150
5.50
VDD/2
VDD/2
VDD/2-1
Units
V
V
V
°C
°C
°C
°C
V
V
V
V
V
V
V
V
mA
mA
mA
pF
ABSOLUTE MAXIMUM RATINGS (note 1)
n
DC CHARACTERISTICS (VDD = 3.3 V unless specified otherwise)
t
AC CHARACTERISTICS (VDD = 3.3 V unless specified otherwise)
h
Input Clock Frequency
See table on page 2
5
80
MHz
Output Clock Frequency
See table on page 2
5
160
MHz
Output Clock Rise Time, CL=30pF
0.8 to 2.0V
1.5
ns
Output Clock Fall Time, CL=30pF
2.0 to 0.8V
1.5
ns
Output Clock Duty Cycle, VDD=3.3V
At VDD/2
40
50
60
%
Device to Device Skew, equally loaded
rising edges at VDD/2
700
ps
Output to Output Skew, equally loaded
rising edges at VDD/2
250
ps
Input to Output Skew, FBIN to CLK8
rising edges at VDD/2
±350
ps
Maximum Absolute Jitter
300
ps
Cycle to Cycle Jitter, 30pF loads
500
ps
Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged
exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability.
2. With CLKIN = 20 MHz, FBIN to CLK8, all outputs at 40 MHz.
3. With CLKIN = 80 MHz, FBIN to CLK8, all outputs at 160 MHz.
3
Revision 051700
Printed 11/15/00
Integrated Circuit Systems, Inc.• 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com
MDS 671-01 B
ICS671-01
Zero Delay, Low Skew Buffer and Multipler
Package Outline and Package Dimensions
(
For current dimensional specifications, see JEDEC Publication No. 95.)
16 pin SOIC narrow
Symbol
A
A1
E
INDEX
AREA
H
B
C
1
2
D
A1
e
Ordering Information
Part/Order Number
ICS671M-01
ICS671M-01T
h x 45°
A
L
D
E
e
H
h
L
Inches
h
Min
Max
0.0532
0.0688
0.0040
0.0098
0.0130
0.0200
0.0075
0.0098
0.3859
0.3937
0.1497
0.1574
.050 BSC
S
0.2284
0.2440
0.0099
0.0195
0.0160 0.0500
Millimeters
m
Min
Max
1.35
1.75
0.10
0.24
0.33
0.51
0.19
0.24
9.80
10.00
3.80
4.00
1.27 BSC
S
5.80
6.20
0.25
0.50
0.41
1.27
B
C
Marking
ICS671M-01
ICS671M-01
Shipping packaging
tubes
tape and reel
Package
16 pin SOIC
16 pin SOIC
Temperature
0-70 °C
0-70 °C
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its
use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is
intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does
not authorize or warrant any ICS product for use in life support devices or critical medical instruments.
4
Revision 051700
Printed 11/15/00
Integrated Circuit Systems, Inc.• 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com
[qq]371263995[/qq] We know that there are many modules in the MSP430 microcontroller, such as reset module, clock module, I/O port module, Timer A module, ADC module, etc. Each module has its structur...
6410 board, want to run the system image in SDRAM, when writing NK.nb0, Checksum is being calculated.... (If you want to skip, press 'x' key) Checksum OK HWindows CE Kernel for ARM (Thumb Enabled) Bui...
[font=黑体][size=3][color=Blue]Who doesn’t like technical knowledge? I believe Sitara high-performance processors are your cup of tea! [/color][/size][/font][font=黑体][size=3] [color=Red]The last live br...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
This paper designs a 16x16LED Chinese character display bar based on single-chip dynamic scanning control, briefly analyzes the principle of Chinese character display, and studies how the LED displ...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
