EEWORLDEEWORLDEEWORLD

Part Number

Search

2-583900-7

Description
CONNECTOR, 50 CONTACT(S), FEMALE, RIGHT ANGLE SINGLE PART CARD EDGE CONN, SOLDER
CategoryThe connector    The connector   
File Size240KB,2 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

2-583900-7 Overview

CONNECTOR, 50 CONTACT(S), FEMALE, RIGHT ANGLE SINGLE PART CARD EDGE CONN, SOLDER

2-583900-7 Parametric

Parameter NameAttribute value
MakerTE Connectivity
Reach Compliance Codeunknown
Connector typeCARD EDGE CONNECTOR
Contact point genderFEMALE
DIN complianceNO
Filter functionNO
IEC complianceNO
MIL complianceNO
Manufacturer's serial number583900
Mixed contactsNO
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of rows loaded2
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts50
Base Number Matches1
ICL7662 cannot be adjusted...
Um, I can’t adjust the inverter circuit. . . .Is there something mysterious about ICL7662? I read the manual and it seems to be fine. Could it be that the new film I bought has a problem?The voltage c...
open82977352 Analog electronics
How to deal with SMD chips when making corrosion boards
I made an etching board today, and the chip pads were placed on the bottom layer. After the product was made, I found that the chip must be placed upside down, which is very difficult to solder. But i...
sw3926 PCB Design
[Very practical] Power adapter transformer calculation and component selection, detailed and complete!
23 steps of adapter design calculation[align=left][align=left]12V1.5A solution design chip:...... [/align] [align=left] 1. Input: 100-264V [/align] [align=left] 2. Output: 12V1.5A [/align] [align=left...
木犯001号 Power technology
ATmega48 output PWM waveform is incorrect, please see the picture
The output needs to be reset to zero every 10 milliseconds. Does anyone have the same problem? #include iom48v.h #include macros.h void main(void) {DDRD |= 0x20;TCCR0A = 0x23; TCCR0B = 0x0B; OCR0A = 5...
lewise88 Microchip MCU
Data丨Xunwei IMX6ULL development board-main frequency and clock configuration routine (Part 2)
Continued from the previous article: as followsThis register uses two bits:STEP_SEL: Select the setp_clk clock source.PLL1_SW_CLK_SEL: Select the pll1_sw_clk clock source.At this point, we can simply ...
遥寄山川 ARM Technology
The problem of external output of P0 port of 51 single chip microcomputer such as AT89S52
Regarding the P0 port of 51 single-chip microcomputers such as AT89S52, I would like to ask everyone, if I do not connect a pull-up resistor, can I directly output high and low levels to the outside?...
PtMao 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1483  890  1330  1042  2481  30  18  27  21  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号