CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Absolute maximum ratings are limiting values, applied individually, beyond which the serviceability of the circuit may be impaired.
Functional operability under any of these conditions is not necessarily implied.
2.
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
PARAMETER
On Hook Power Dissipation
Off Hook Power Dissipation
Off Hook I
B
+
Off Hook I
B
+
Off Hook I
B
-
Off Hook Loop Current
Off Hook Loop Current
Off Hook Loop Current
Fault Currents
TIP to Ground
RING to Ground
TIP to RING
TIP and RING to Ground
Ring Relay Drive V
OL
Ring Relay Driver Off Leakage
Ring Trip Detection Period
Switch Hook Detection Threshold
Unless Otherwise Specified, V
B
- = -48V, V
B
+ = 12V and 5V, AG = BG = DG = 0V, Typical Parameters
T
A
= 25°C. Min-Max Parameters are Over Operating Temperature Range
CONDITIONS
I
LONG
= 0 (Note 3), V
B
+ = 12V
R
L
= 600, I
LONG
= 0 (Note 3), V
B
+ = 12V
R
L
= 600, I
LONG
= 0 (Note 3), T
A
= -40°C
R
L
= 600, I
LONG
= 0 (Note 3), T
A
= 25°C
R
L
= 600, I
LONG
= 0 (Note 3)
R
L
= 1200, I
LONG
= 0 (Note 3)
R
L
= 1200, V
B
- = -42V, I
LONG
= 0 (Note 3)
T
A
= 25°C
R
L
= 200, I
LONG
= 0 (Note 3)
MIN
-
-
-
-
-
-
17.5
36
TYP
170
425
-
-
35
21
-
41
MAX
235
550
6.0
5.3
41
-
-
48
UNITS
mW
mW
mA
mA
mA
mA
mA
mA
-
-
-
-
I
OL
= 62mA
V
RD
= 12V, RC = 1 = HIGH, T
A
= 25°C
R
L
= 600
SHD = V
OL
SHD = V
OH
-
-
-
10
-
20
-
14
55
41
55
0.2
-
2
-
-
-
-
-
-
-
-
0.5
100
3
-
5
-
10
mA
mA
mA
mA
V
A
Ring
Cycles
mA
mA
mA
mA
Ground Key Detection Threshold
GKD = V
OL
GKD = V
OH
FN2886 Rev 8.00
July 2004
Page 2 of 9
HC-5504B
Electrical Specifications
PARAMETER
Loop Current During Power Denial
Dial Pulse Distortion
Receive Input Impedance
Transmit Output Impedance
2-Wire Return Loss
SR
L
LO
ER
L
SR
L
HI
Longitudinal Balance
2-Wire Off Hook
2-Wire On Hook
4-Wire Off Hook
Low Frequency Longitudinal Balance
R.E.A. Method (Note 3), R
L
= 600
0°C
T
A
75°C
at 1kHz, 0dBm Input Level, Referenced 600
-
200Hz - 3400Hz Referenced to Absolute Loss at
1kHz and 0dBm Signal Level (Note 3)
(Note 3)
-
-
Absolute Delay
2-Wire to 4-Wire, 4 Wire to 2-Wire
Trans Hybrid Loss
Overload Level
2-Wire to 4-Wire, 4 Wire to 2-Wire
Level Linearity
2-Wire to 4-Wire, 4 Wire to 2-Wire
Balance Network Set Up for 600 Termination at
1kHz
V
B
+ = +5V
V
B
+ = 12V
At 1kHz Referenced to 0dBm Level (Note 3)
+3 to -40dBm
-40 to -50dBm
-50 to -55dBm
Power Supply Rejection Ratio
V
B
+ to 2-Wire
V
B
+ to Transmit
V
B
- to 2-Wire
V
B
- to Transmit
(Note 3)
30 - 60Hz, R
L
= 600
15
15
15
15
-
-
-
-
-
-
-
-
dB
dB
dB
dB
-
-
-
-
-
-
0.05
0.1
0.3
dB
dB
dB
(Note 3)
-
36
1.5
1.75
-
40
-
-
2
-
-
-
ms
dB
V
PEAK
V
PEAK
1
-89
5
-85
dBrnC
dBm0p
-
0.05
0.02
0.2
0.05
dB
dB
1V
RMS
200Hz - 3400Hz (Note 3) IEEE Method
0°C
T
A
75°C
(Note 3)
(Note 3)
Referenced to 600 + 2.16F (Note 3)
-
-
-
15.5
24
31
-
-
-
dB
dB
dB
R
L
= 200
Unless Otherwise Specified, V
B
- = -48V, V
B
+ = 12V and 5V, AG = BG = DG = 0V, Typical Parameters
T
A
= 25°C. Min-Max Parameters are Over Operating Temperature Range
(Continued)
CONDITIONS
MIN
-
0
-
-
TYP
2
-
110
10
MAX
-
5
-
20
UNITS
mA
ms
k
58
60
50
-
-
65
63
58
-
-
-
-
-
23
-67
dB
dB
dB
dBrnC
dBm0p
Insertion Loss
2-Wire to 4-Wire, 4 Wire to 2-Wire
Frequency Response
Idle Channel Noise
2-Wire to 4-Wire, 4 Wire to 2-Wire
FN2886 Rev 8.00
July 2004
Page 3 of 9
HC-5504B
Electrical Specifications
PARAMETER
V
B
+ to 2-Wire
V
B
+ to Transmit
V
B
- to 2-Wire
V
B
- to Transmit
Logic Input Current (RS, RC, PD)
Logic Inputs
Logic ‘0’ V
IL
Logic ‘1’ V
IH
Logic Outputs
Logic ‘0’ V
OL
Logic ‘1’ V
OH
I
LOAD
800A, V
B
+ = 12V, 5V
I
LOAD
80A, V
B
+ = 12V
I
LOAD
40A, V
B
+ = 5V
-
2.7
2.7
0.1
5.0
-
0.5
5.5
5.0
V
V
V
-
2.0
-
-
0.8
5.5
V
V
0V
V
IN
5V
Unless Otherwise Specified, V
B
- = -48V, V
B
+ = 12V and 5V, AG = BG = DG = 0V, Typical Parameters
T
A
= 25°C. Min-Max Parameters are Over Operating Temperature Range
(Continued)
CONDITIONS
200 - 16kHz, R
L
= 600
MIN
30
30
30
30
-
TYP
-
-
-
-
-
MAX
-
-
-
-
100
UNITS
dB
dB
dB
dB
A
Uncommitted Op Amp Specifications
PARAMETER
Input Offset Voltage
Input Offset Current
Input Bias Current
Differential Input Resistance
Output Voltage Swing
(Note 3)
R
L
= 10K, V
B
+ = 12V
R
L
= 10K, V
B
+ = 5V
Output Resistance
Small Signal GBW
NOTES:
3. These parameters are controlled by design or process parameters and are not directly tested. These parameters are characterized upon initial
design release, upon design changes which would affect these characteristics, and at intervals to assure product quality and specification
compliance.
4. I
LONG
= Longitudinal Current.
A
VCL
= 1 (Note 3)
(Note 3)
CONDITIONS
MIN
-
-
-
-
-
-
-
-
TYP
5
10
20
1
6.2
3
10
1
MAX
-
-
-
-
6.6
-
-
-
UNITS
mV
nA
nA
M
V
PEAK
V
PEAK
MHz
FN2886 Rev 8.00
July 2004
Page 4 of 9
HC-5504B
Pin Descriptions
24 PIN
SOIC
1
SYMBOL
TIP
DESCRIPTION
An analog input connected to the TIP (more positive) side of the subscriber loop through a 150 feed resistor and a
ring relay contact. Functions with the Ring terminal to receive voice signals from the telephone and for loop
monitoring purposes.
An analog input connected to the RING (more negative) side of the subscriber loop through a 150 feed resistor and
a ring relay contact. Functions with the Tip terminal to receive voice signals from the telephone and for loop
monitoring purposes.
Senses ring side of loop for ground key and ring trip detection. During ringing, the ring signal is inserted into the line
at this node and RF is isolated from RFS via a relay.
Positive Voltage Source - Most positive supply. V
B
+ is typically 12V or 5V.
Capacitor #3 - An external capacitor to be connected between this terminal and analog ground. Required for proper
operation of the loop current limiting function, and for filtering V
B
-. Typical value is 0.3F, 30V.
Digital Ground - To be connected to zero potential and serves as a reference for all digital inputs and outputs on the
SLIC microcircuit.
Ring Synchronization Input - A TTL-compatible clock input. The clock should be arranged such that a positive pulse
transition occurs on the zero crossing of the ring voltage source, as it appears at the RFS terminal. For Tip side
injected systems, the RS pulse should occur on the negative going zero crossing and for Ring injected systems, on
the positive going zero crossing. This ensures that the ring relay activates and deactivates when the instantaneous
ring voltage is near zero. If synchronization is not required, the pin should be tied to 5V.
Relay Driver - A low active open collector logic output. When enabled, the external ring relay is energized.
Tip Feed - A low impedance analog output connected to the TIP terminal through a 150 feed resistor. Functions
with the RF terminal to provide loop current, feed voice signals to the telephone set, and sink longitudinal current.
Ring Feed - A low impedance analog output connected to the RING terminal through a 150 feed resistor. Functions
with the TF terminal to provide loop current, feed voice signals to the telephone set, and sink longitudinal current.
Negative Voltage Source - Most negative supply. V
B
- is typically -48V with an operational range of -42V to -58V.
Frequently referred to as “battery”.
Battery Ground - To be connected to zero potential. All loop current and some quiescent current flows into this ground
terminal.
Switch Hook Detection - A low active LS TTL - compatible logic output. This output is enabled for loop currents
exceeding 10mA and disabled for loop currents less than 5mA.
Ground Key Detection - A low active LS TTL - compatible logic output. This output is enabled if the DC current into
the ring lead exceeds the DC current out of the tip lead by more than 20mA, and disabled if this current difference is
less than 10mA.
Power Denial - A low active TTL - Compatible logic input. When enabled, the switch hook detect (SHD) and ground
key detect (GKD) are not necessarily valid, and the relay driver (RD) output is disabled.
Ring Command - A low active TTL - Compatible logic input. When enabled, the relay driver (RD) output goes low on
the next high level of the ring sync (RS) input, as long as the SLIC is not in the power denial state (PD = 0) or the
subscriber is not already off- hook (SHD = 0).
Capacitor #2 - An external capacitor to be connected between this terminal and digital ground. Prevents false ground
key indications from occurring during ring trip detection. Typical value is 0.15F, 10V. This capacitor is not used if
ground key function is not required and (Pin 17) may be left open or connected to digital ground.
The analog output of the spare operational amplifier. The output voltage swing is typically
5V.
The inverting analog input of the spare operational amplifier.
The non-inverting analog input of the spare operational amplifier.
Receive Input, 4-Wire Side - A high impedance analog input which is internally biased. Capacitive coupling to this
input is required. AC signals appearing at this input differentially drive the Tip feed and Ring feed terminals, which in
turn drive tip and ring through 300 of feed resistance on each side of the line.
Capacitor #4 - An external capacitor to be connected between this terminal and analog ground. This capacitor
prevents false ground key indication and false ring trip detection from occurring when longitudinal currents are
induced onto the subscriber loop from near by power lines and other noise sources. This capacitor is also required
for the proper operation of ring trip detection. Typical value is 0.5F, to 1.0F, 20V. This capacitor should be
京公网安备 11010802033920号
EEWORLD
