All specifications are based on 25°C, Nominal Input Voltage (115V and 230V), <75% Humidity and Rated Output Load unless otherwise noted.
We reserve the right to change specifications based on technological advances.
GENERAL SPECIFICATIONS
Efficiency
Isolation Voltage
Switching Frequency
PHYSICAL SPECIFICATIONS
Weight
Dimensions (L x W x H)
Cooling
SAFETY CHARACTERISTICS
Safety Standards & Certifications
Safety Class
EMI
ESD
RS
EFT
Surge
CS
Voltage Dips, Short Interruptions and
Voltage Variations Immunity
TEST CONDITIONS
Input-Output, 1 minute Test Time
Min
3000
Typ
Max
Unit
VAC
kHz
See Table
65
0.21oz (6g)
1.38in x 0.65in x 0.43in
(35mm x 16.45mm x 11mm)
1.38in x 0.71in x 0.43in
(35mm x 18mm x 11mm)
Free Convection
SIP Model
SIP Model with 90º Bend
CE
RE
IEC/EN61000-4-2
IEC/EN61000-4-3
IEC/EN61000-4-4
IEC/EN61000-4-4
IEC/EN61000-4-5
IEC/EN61000-4-5
IEC/EN61000-4-6
IEC/EN61000-4-11
IEC60950, EN60950, UL60950
(11)
Class II
(4)
CISPR32/EN55032
CISPR32/EN55032
(5)
CISPR32/EN55032
(4)
CISPR32/EN55032
(5)
±4kV
10V/m
(5)
±2kV
(4)
±4kV
(5)
Line to line ±1kV
(4)
Line to line ±1kV/line to ground ±2kV
(5)
10Vr.m.s
(5)
0%, 70%
(5)
Class A
Class B
Class A
Class B
Perf. Criteria B
Perf. Criteria A
Perf. Criteria B
Perf. Criteria B
Perf. Criteria B
Perf. Criteria B
Perf. Criteria A
Perf. Criteria B
Add -F to model name to indicate 90º corner model.
When 3.3V/5V/9V/12V models are working in -20-40ºC temperature range output filter capacitor C2 needs 270µF/16V solid-state capacitor.
Ripple & Noise are measured by “parallel cable” method.
See Fig. 1 for typical application circuit.
See Fig. 2 for recommended circuit.
External electrolytic capacitors are required to use modules.
This part is open frame, at least 6.4mm safety distance between the primary and secondary external components of the module is needed to meet
safety requirement.
8. In order to increase the conversion efficiency of the product with light load in the design, the product will have audio noise when it is operating, but
it will not affect the product’s reliability and performance.
9. Module requires dispensing fixed after assembly.
10. Product customization available.
11. This product is Listed to applicable standards and requirements by UL.
*Due
to advances in technology, specifications subject to change without notice.
The STM32 chip selected in this book is based on the ARM Cortex-M3 architecture. According to the actual application requirements of MCU-based embedded technology, a variety of commonly used important...
[i=s] This post was last edited by Brother Meng Yi on 2015-12-21 15:35 [/i] [align=left][font=微软雅黑][size=3]In short, what we are going to learn in this section is a serial communication protocol. The ...
For single-ended output/input, we can consider it as 50 Ohm. For double-ended differential ports, such as CC253x and CC254x, the differential impedance is a non-standard value.TI recommends copying th...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
As a simple and practical input device, buttons have been used in various microcontroller application systems and are ubiquitous. However, the buttons used in different practical occasions are also...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
