Changes to Ordering Guide .......................................................... 20
7/04—Revision 0: Initial Version
AD7940
SPECIFICATIONS
1
V
DD
= 2.50 V to 5.5 V, f
SCLK
= 2.5 MHz, f
SAMPLE
= 100 kSPS, unless otherwise noted; T
A
= T
MIN
to T
MAX
, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion (SINAD)
2
Total Harmonic Distortion (THD)
2
Peak Harmonic or Spurious Noise (SFDR)
2
Intermodulation Distortion (IMD)
2
Second-Order Terms
Third-Order Terms
Aperture Delay
Aperture Jitter
Full Power Bandwidth
DC ACCURACY
Resolution
Integral Nonlinearity
2
Offset Error
2
Gain Error
2
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance
LOGIC INPUTS
Input High Voltage, V
INH
Input Low Voltage, V
INL
Input Current, I
IN
Input Capacitance, C
IN2, 3
LOGIC OUTPUTS
Output High Voltage, V
OH
Output Low Voltage, V
OL
Floating-State Leakage Current
Floating-State Output Capacitance
2, 3
Output Coding
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
Throughput Rate
POWER REQUIREMENTS
V
DD
I
DD
Normal Mode (Static)
Normal Mode (Operational)
Full Power-Down Mode
B Version
1
81
−98
−95
−94
−100
20
30
7
2
14
13
±1
±2
±6
±8
0 to V
DD
±0.3
30
2.4
0.4
0.8
±0.3
10
Unit
dB min
dB typ
dB typ
dB typ
dB typ
ns max
ps typ
MHz typ
MHz typ
Bits min
Bits min
LSB max
LSB max
LSB max
LSB max
V
µA max
pF typ
V min
V max
V max
µA max
pF max
Test Conditions/Comments
f
IN
= 10 kHz sine wave
@ −3 dB
@ −0.1 dB
V
DD
= 2.5 V to 4.096 V
V
DD
> 4.096 V
V
DD
= 2.5 V to 4.096 V
V
DD
> 4.096 V
V
DD
= 3 V
V
DD
= 5 V
Typically 10 nA, V
IN
= 0 V or V
DD
V
DD
– 0.2
V min
0.4
V max
±0.3
µA max
10
pF max
Straight (Natural) Binary
8
500
400
100
2.50/5.5
5.2
2
4.8
1.9
0.5
0.3
µs max
ns max
ns max
kSPS max
V min/V max
mA max
mA max
mA max
mA max
µA max
µA max
Rev. A | Page 3 of 20
I
SOURCE
= 200 µA; V
DD
= 2.50 V to 5.25 V
I
SINK
= 200 µA
16 SCLK cycles
Full-scale step input
Sine wave input ≤ 10 kHz
See the Serial Interface section
Digital I/P
S
= 0 V or V
DD
V
DD
= 5.5 V; SCLK on or off
V
DD
= 3.6 V; SCLK on or off
V
DD
= 5.5 V; f
SAMPLE
= 100 kSPS; 3.3 mA typ
V
DD
= 3.6 V; f
SAMPLE
= 100 kSPS; 1.29 mA typ
SCLK on or off. V
DD
= 5.5 V
SCLK on or off. V
DD
= 3.6 V
AD7940
Parameter
Power Dissipation
4
Normal Mode (Operational)
Full Power-Down
1
2
B Version
1
26.4
6.84
2.5
1.08
Unit
mW max
mW max
µW max
µW max
Test Conditions/Comments
V
DD
= 5.5 V
V
DD
= 5.5 V; f
SAMPLE
= 100 kSPS
V
DD
= 3.6 V; f
SAMPLE
= 100 kSPS
V
DD
= 5.5 V
V
DD
= 3.6 V
Temperature range for B Version is –40°C to +85°C.
See the Terminology section.
3
Sample tested at initial release to ensure compliance.
4
See the Power vs. Throughput Rate section.
Rev. A | Page 4 of 20
AD7940
TIMING SPECIFICATIONS
Sample tested at initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of V
DD
) and timed from
a voltage level of 1.6 V.
V
DD
= 2.50 V to 5.5 V; T
A
= T
MIN
to T
MAX
, unless otherwise noted.
Table 3.
Parameter
f
SCLK 1
t
CONVERT
t
QUIET
t
1
t
2
t
3 2
t
4 2
t
5
t
6
t
7
t
8 3
t
POWER-UP 4
1
2
Limit at T
MIN
, T
MAX
3V
5V
250
250
2.5
2.5
16 × t
SCLK
16 × t
SCLK
50
50
10
10
48
120
0.4 t
SCLK
0.4 t
SCLK
10
45
1
10
10
35
80
0.4 t
SCLK
0.4 t
SCLK
10
35
1
Unit
kHz min
MHz max
min
ns min
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns max
µs typ
Description
Minimum quiet time required between bus relinquish and start of
next conversion
Minimum CS pulse width
CS to SCLK setup time
Delay from CS until SDATA three-state disabled
Data access time after SCLK falling edge
SCLK low pulse width
SCLK high pulse width
SCLK to data valid hold time
SCLK falling edge to SDATA high impedance
Power up time from full power-down
Mark/space ratio for the SCLK input is 40/60 to 60/40.
Measured with the load circuit of Figure 2 and defined as the time required for the output to cross 0.8 V or 2.0 V.
3
t
8
is derived form the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 2. The measured number is then extrapolated
back to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t
8
, quoted in the timing characteristics is the true bus relinquish
time of the part and is independent of the bus loading.
4
See the Power vs. Throughput Rate section.
200µA
I
OL
TO OUTPUT
PIN
1.6V
C
L
50pF
200µA
I
OH
03305-0-002
Figure 2. Load Circuit for Digital Output Timing Specification
Yesterday I got two CC2538 SmartRF06EB development kits. I debugged them with GenericApp in the protocol stack Z-Stack-Mesh-1.0.0. One board was burned into a coordinator, PANid was set to 0x6018, cha...
Ultrasonic level meter, differential level meter, flow meter (1) Screen operation control. One ultrasonic differential level meter is installed on each coarse screen and fine screen. The difference in...
Based on ise14.7, I used the Nexys3 development board to play with the read-only memory today. The source code is as follows: module rom8( input wire[2:0]addr, output wire[7:0]M ); parameter N=8;//The...
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
I've been studying dot matrix recently. It looks simple, but it takes a while to master it completely! The 8*8 dot matrix hardware circuit I'm making now is like this. The row is driven by 74HC138 + t...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
0 Introduction
High-precision current source can provide high-precision current supply for precision instruments, and is suitable for automatic measurement tasks of various resistors in semico...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
introduction
Steam turbines are driven by high-temperature and high-pressure steam generated by boilers to run at high speed. They are key power equipment in thermal power plants. The emergenc...[Details]
As the global LED market demand continues to increase, my country's LED industry will face huge opportunities in the future. However, the core LED technology and patents are basically monopolized b...[Details]
A few days ago, I bought an 8LED flashlight in the market (the flashlight uses No. 5 batteries). Because I had other things to do, I didn't pay attention when purchasing it. When I got home and use...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
