– Compatible with Hot-Plug I/O expanders used on PC mother-
boards
Power Management
– Utilizes advanced low-power design techniques to achieve low
typical power consumption
– Supports PCI Power Management Interface specification (PCI-
PM 1.2)
– Unused SerDes are disabled.
– Supports Advanced Configuration and Power Interface Speci-
fication, Revision 2.0 (ACPI) supporting active link state
Testability and Debug Features
– Built in Pseudo-Random Bit Stream (PRBS) generator
– Numerous SerDes test modes
– Ability to bypass link training and force any link into any mode
– Provides statistics and performance counters
Block Diagram
4-Port Switch Core / 4 PCI Express Lanes
Frame Buffer
Route Table
Port
Arbitration
Scheduler
Transaction Layer
Data Link Layer
Transaction Layer
Data Link Layer
Transaction Layer
Data Link Layer
Transaction Layer
Data Link Layer
Mux / Demux
Phy
Logical
Layer
Mux / Demux
Phy
Logical
Layer
Mux / Demux
Phy
Logical
Layer
Mux / Demux
Phy
Logical
Layer
SerDes
SerDes
SerDes
SerDes
(Port 0)
(Port 2)
(Port 3)
(Port 4)
Figure 1 Internal Block Diagram
IDT and the IDT logo are registered trademarks of Integrated Device Technology, Inc.
1 of 30
June 12, 2014
IDT 89HPES4T4 Data Sheet
5 General Purpose Input/Output Pins
– Each pin may be individually configured as an input or output
– Each pin may be individually configured as an interrupt input
– Each pin has a selectable alternate function
Option A Package: 13mm x 13mm 144-ball BGA with 1mm ball spacing
Option B Package: 10mm x 10mm 132-ball QFN with 1mm ball spacing
Product Description
Utilizing standard PCI Express interconnect, the PES4T4 provides the most efficient fan-out solution for applications requiring x1 connectivity, low
latency, and simple board layout with a minimum number of board layers. Each lane provides 2.5 Gbps of bandwidth in both directions and is fully
compliant with PCI Express Base specification 1.1.
The PES4T4 is based on a flexible and efficient layered architecture. The PCI Express layer consists of SerDes, Physical, Data Link and Transac-
tion layers in compliance with PCI Express Base specification Revision 1.1. The PES4T4 can operate either as a store and forward or cut-through
switch and is designed to switch memory and I/O transactions. It supports eight Traffic Classes (TCs) and one Virtual Channel (VC) with sophisticated
resource management to allow efficient switching for applications requiring additional narrow port connectivity and also some high-end connectivity.
Processor
Processor
North
Bridge
Memory
Memory
Memory
Memory
South
Bridge
x1
PES4T4
x1
GE
LOM
x1
GE
LOM
x1
1394
Figure 2 I/O Expansion Application
SMBus Interface
The PES4T4 contains an SMBus master interface. This master interface allows the default configuration register values of the PES4T4 to be over-
ridden following a reset with values programmed in an external serial EEPROM. The master interface is also used by an external Hot-Plug I/O
expander. Two pins make up the SMBus master interface. These pins consist of an SMBus clock pin and an SMBus data pin.
Hot-Plug Interface
The PES4T4 supports PCI Express Hot-Plug on each downstream port. To reduce the number of pins required on the device, the PES4T4 utilizes
an external I/O expander, such as that used on PC motherboards, connected to the SMBus master interface. Following reset and configuration, when-
ever the state of a Hot-Plug output needs to be modified, the PES4T4 generates an SMBus transaction to the I/O expander with the new value of all of
the outputs. Whenever a Hot-Plug input changes, the I/O expander generates an interrupt which is received on the IOEXPINTN input pin (alternate
function of GPIO) of the PES4T4. In response to an I/O expander interrupt, the PES4T4 generates an SMBus transaction to read the state of all of the
Hot-Plug inputs from the I/O expander.
2 of 30
June 12, 2014
IDT 89HPES4T4 Data Sheet
General Purpose Input/Output
The PES4T4 provides 5 General Purpose Input/Output (GPIO) pins that may be used by the system designer as bit I/O ports. Each GPIO pin may
be configured independently as an input or output through software control, and some GPIO pins are shared with another on-chip functions. These
alternate functions may be enabled via software or serial configuration EEPROM.
Pin Description
The following tables lists the functions of the pins provided on the PES4T4. Some of the functions listed may be multiplexed onto the same pin. The
active polarity of a signal is defined using a suffix. Signals ending with an “N” are defined as being active, or asserted, when at a logic zero (low) level.
All other signals (including clocks, buses, and select lines) will be interpreted as being active, or asserted, when at a logic one (high) level.
Signal
PE0RP[0]
PE0RN[0]
PE0TP[0]
PE0TN[0]
PE2RP[0]
PE2RN[0]
PE2TP[0]
PE2TN[0]
PE3RP[0]
PE3RN[0]
PE3TP[0]
PE3TN[0]
PE4RP[0]
PE4RN[0]
PE4TP[0]
PE4TN[0]
PEREFCLKP
PEREFCLKN
Type
I
O
I
O
I
O
I
O
I
Name/Description
PCI Express Port 0 Serial Data Receive.
Differential PCI Express receive
pair for port 0.
PCI Express Port 0 Serial Data Transmit.
Differential PCI Express trans-
mit pair for port 0.
PCI Express Port 2 Serial Data Receive.
Differential PCI Express receive
pair for port 2.
PCI Express Port 2 Serial Data Transmit.
Differential PCI Express trans-
mit pair for port 2.
PCI Express Port 3 Serial Data Receive.
Differential PCI Express receive
pair for port 3.
PCI Express Port 3 Serial Data Transmit.
Differential PCI Express trans-
mit pair for port 3.
PCI Express Port 4 Serial Data Receive.
Differential PCI Express receive
pair for port 4.
PCI Express Port 4 Serial Data Transmit.
Differential PCI Express trans-
mit pair for port 4.
PCI Express Reference Clock.
Differential reference clock pair input. This
clock is used as the reference clock by on-chip PLLs to generate the clocks
required for the system logic and on-chip SerDes.
Table 1 PCI Express Interface Pins
Signal
MSMBCLK
MSMBDAT
Type
I/O
I/O
Name/Description
Master SMBus Clock.
This bidirectional signal is used to synchronize
transfers on the master SMBus.
Master SMBus Data.
This bidirectional signal is used for data on the mas-
ter SMBus.
Table 2 SMBus Interface Pins
3 of 30
June 12, 2014
IDT 89HPES4T4 Data Sheet
Signal
GPIO[0]
Type
I/O
Name/Description
General Purpose I/O.
This pin can be configured as a general purpose I/O pin.
Alternate function pin name: P2RSTN
Alternate function pin type: Output
Alternate function: Reset output for downstream port 2
General Purpose I/O.
This pin can be configured as a general purpose I/O pin.
Alternate function pin name: P4RSTN
Alternate function pin type: Output
Alternate function: Reset output for downstream port 4
General Purpose I/O.
This pin can be configured as a general purpose I/O pin.
The most impressive thing in the opening ceremony of the Beijing Olympics was probably the huge scroll in the center of the venue. Two 22-meter-long scrolls were slowly pulled apart, revealing a huge ...
Description The TMP103 is a digital output temperature sensor in a 4-ball wafer chip scale package (WCSP). The TMP103 can read temperatures with a resolution of 1°C. The TMP103 has a two-wire interfac...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:24[/i] My graduation project is a 16*16 dot matrix LED electronic display. Could you give me some relevant information? Thank you....
In the EVC environment, the _wfopen function is used to open the specified file. It can be used to open several files at the same time, but when opening more files, an error occurs and the opened file...
Having been cheated countless times has given me a keen eye, and I can tell whether a refurbished chip is real or fake as soon as I get it.
This is the DS90C124 I bought from Taobao. The seller descri...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
The data collector of the automatic weather station is generally designed based on a single-chip microcomputer or a PC/104 bus controller. It has the characteristics of good compatibility with PC, low...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
