EEWORLDEEWORLDEEWORLD

Part Number

Search

66121

Description
Anti-Static Control Products 30X24 STATFREE MAT
CategoryTools and equipment   
File Size548KB,4 Pages
ManufacturerDESCO
Environmental Compliance
Download Datasheet Parametric Compare View All

66121 Online Shopping

Suppliers Part Number Price MOQ In stock  
66121 - - View Buy Now

66121 Overview

Anti-Static Control Products 30X24 STATFREE MAT

66121 Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerDESCO
Product CategoryAnti-Static Control Products
RoHSDetails
ProductAnti-Static Surfaces
TypeTable Mat
Factory Pack Quantity1
Unit Weight30 lbs
TECHNICAL BULLETIN TB-2000
Installation and
Maintenance of ESD Mats
Introduction
09814
Made in the
United States of America
09817
The purpose of an ESD worksurface is to aid in the prevention
of damage to ESD sensitive components and assemblies from
electrostatic discharge. An ESD worksurface provides protection in
the following two ways:
1. Providing an antistatic worksurface area that will limit static
electricity generation.
2. Removing the charge from a conductive object placed on the
worksurface.
A dissipative worksurface having a surface resistance of at least 1
x 10
6
, but less than 1 x 10
9
ohms is recommended by worksurface
standard ANSI/ESD S4.1. Dissipative materials minimize the
generation of static charges, and will dissipate a charge slow
enough so that a spark will not occur. Dissipative materials are
usually the preferred choice for bench top worksurfaces.
Conductive materials are the quickest to remove a charge,
but they can also cause damage by discharging too rapidly.
Conductive materials are usually used as floor mats, which is
defined by ANSI/ESD S7.1 as less than 1 x 10
6
ohms.
Figure 3.
09814
with screw allows ground cord to be bolted to mat
to keep cord from disconnecting.
Common point grounds are designed to provide ground for
worksurface mats, wrist straps, and other items.
NOTE:
DO NOT DAISY CHAIN. Because of the high resistances
inherent to many types of protective surfaces, daisy chaining of
these materials can severely limit their ability to properly dissipate
and protect against static charges.
Figure 2. Other ground cords.
General Grounding Guidelines
1. ANSI/ESD S20.20 requires that all conductors in an ESD
protected area, including personnel, must be grounded.
2. The ESD ground must be tied directly to and at the same
potential as the building or “green wire” equipment ground.
3. Per ANSI/ESD S20.20, the ESD control program can in no
way replace or supercede any requirements for personnel
safety. Ground fault circuit interrupters (GFCI) and other safety
protection should be considered wherever personnel might
come into contact with electrical sources.
4. All electrical outlets should be verified for proper wiring
configuration, resistance or impedance and GFCI function when
the mat is installed and periodically thereafter.
COMMON POINT GROUND
Per ANSI/ESD S6.1, Grounding section 4.1.1 “Every element to be
grounded at an ESD protected station shall be connected to the
same common point ground.”
ESD Handbook ESD TR20.20 section 5.1.3 Basic Grounding
Requirements “The first step in ensuring that everything in an
EPA is at the same electrical potential is to ground all conductive
components of the work area (worksurfaces, people, equipment,
etc.) to the same electrical ground point. This point is called the
common point ground. The next step in completing the ground
circuit is to connect the common point ground to the equipment
ground (third wire, green).”
Common Point Grounds
A common point ground is defined by the grounding standard
ANSI/ESD S6.1, as:
1. A grounded device where two or more conductors are bonded.
2. A system or method for connecting two or more grounding
conductors to the same electrical potential.
Examples of common point grounds with ground cords are
illustrated below.
09835
WRONG!
RIGHT
09825
09837
09740
Figure 4. ESD mats should never be grounded in series, that is
daisy chained.
Figure 1. Typical common point grounds.
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178
DESCO EAST
- One Colgate Way,
Canton, MA 02021-1407 • (781) 821-8370 • Web Site:
Desco.com
TB-2000
February 2015 Page 1 of 4
© 2015 DESCO INDUSTRIES INC.
Employee Owned

66121 Related Products

66121 42480 66168 66169 66164 66166 66167 15006 82067 15005
Description Anti-Static Control Products 30X24 STATFREE MAT Anti-Static Control Products 24X48IN 3 LAYER MAT Anti-Static Control Products MATTOP 2LYR DK BLU .060X30X72" Anti-Static Control Products MATTOP 2LYR DK BLU .060X36X72" Anti-Static Control Products MATTOP 2LYR DK BLU .060X24X36" Anti-Static Control Products MATTOP 2LYR DK BLU .060X24X48" Anti-Static Control Products MATTOP 2LYR DK BLU .060X30X60" Anti-Static Control Products MAT STATFREE CV VINYL Anti-Static Control Products Statfree Mat G2 BLK w/Grd, .060x48x72 Anti-Static Control Products ROLL STATFREE CV VINYL
Product Attribute Attribute Value Attribute Value Attribute Value Attribute Value Attribute Value Attribute Value Attribute Value Attribute Value Attribute Value Attribute Value
Manufacturer DESCO DESCO DESCO DESCO DESCO DESCO DESCO DESCO DESCO DESCO
Product Category Anti-Static Control Products Anti-Static Control Products Anti-Static Control Products Anti-Static Control Products Anti-Static Control Products Anti-Static Control Products Anti-Static Control Products Anti-Static Control Products Anti-Static Control Products Anti-Static Control Products
RoHS Details Details Details Details Details Details Details Details Not Applicable Details
Factory Pack Quantity 1 1 1 1 1 1 1 1 1 1
Product Anti-Static Surfaces - Anti-Static Surfaces Anti-Static Surfaces Anti-Static Surfaces Anti-Static Surfaces Anti-Static Surfaces - - -
Type Table Mat - Table Mat Table Mat Table Mat Table Mat Table Mat - - -
Has anyone used EVC to develop symbol mc1000?
The requirement is very simple, that is, every time you scan a barcode, write a line in a UP.TXT, and then scan the barcode again and write it in the second line, until you no longer scan the barcode....
wangwenjia Embedded System
Question: How to call the calculator in the driver?
I want to pop up a calculator on the keyboard with one click. I used WinExec("calc.exe",SW_SHOWNORMAL); but the compilation fails and the error 'WinExec' undefined; assuming extern returning int 'SW_S...
ATT001 Embedded System
Reasons why the POE module does not supply power
People often encounter this problem. When using a non-isolated module with a POE switch, several POE switch ports will not be powered. What is the problem? This is because of the POE chip on the POE m...
达普POE交换机 Industrial Control Electronics
The peak of the switching power supply [attached picture], is this considered high?
I used a switching power supply in my project, and I felt that the burrs were relatively large during use. Some power modules would cause the digital circuit to malfunction (the digital module would w...
子乐 Power technology
Why are aluminum electrolytic capacitors used in LED lighting circuits? What are the precautions?
LED lighting power supply belongs to switching power supply. Using aluminum electrolytic capacitor for filtering is an indispensable part of switching power supply design. The normal working life of s...
qwqwqw2088 Power technology
Thoughts on Communication
I want to try out communications next, please give me some direction! I don't know how to learn it....
zhaoqibinpp RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 933  2649  203  2618  2216  19  54  5  53  45 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号