PRODUCT SPECIFICATION
MICRO-FIT BMI FLOATING CONNECTOR SYSTEM
1.0 SCOPE
This Product Specification covers the 3.00 mm (.118 inch) centerline (pitch) connector system
terminated with 20 to 30 AWG wire using crimp technology with tin plating.
2.0 PRODUCT DESCRIPTION
2.1 PRODUCT NAME AND SERIES NUMBERS
Micro-Fit Dual Row BMI Floating Panel Receptacle: 44133
Female Crimp Terminal: 43030
Micro-Fit Dual Row BMI Panel Mount Plug: 44300
Male Crimp Terminal: 43031
Micro-Fit Dual Row BMI Receptacle Headers: 44764 and 44769
Micro-Fit Dual Row BMI Headers: 44428 and 44432
Micro-Fit Dual Row BMI Vertical CPI Header : 45280
Micro-Fit Single Row BMI Floating Panel Receptacle: 46623
Micro-Fit Single Row BMI Panel Mount Plug: 46625
Micro-Fit Single Row BMI Headers: 46622
Test Plug: 44242 (recommended for continuity testing only)
2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS
(See the appropriate Sales Drawings for details)
Crimp Terminals: Phosphor Bronze
Panel Receptacle and Plug: Polyester, Nylon
Headers: High Temp Nylon, LCP
Header Pins and Terminals: Brass, Modified Tin/Brass, Phosphor Bronze
2.3 SAFETY AGENCY APPROVALS
UL File Number:?. E29179
CSA:??????.. LR19980
IEC 61984 Certification: Tested to and found in compliance with IEC 61984. NRTL type
examination certificate available from Molex upon request.
Contact Molex Safety Agency team
for questions regarding certification on specific part numbers.”
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
Test Summary: TS-43045-001
REVISION:
TITLE:
EC No:
UCP2016-3198
DATE:
2016/02/17
L3
PRODUCT SPECIFICATION
Micro-Fit (3.0)
BMI Floating Connector System
CHECKED BY:
SHEET No.
1
of
12
F.SMITH
DOCUMENT NUMBER:
CREATED / REVISED BY:
APPROVED BY:
PS-44300-001
CSLAFTER
S.SOUSEK
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
4.0 RATINGS
4.1 SAFETY AGENCY RATINGS
Agency Voltage Rating
(AC RMS or DC)
Series
UL
CSA
IEC
44133
44300
44428
44432
44764
44769
45280
46622
46623
46625
250
250
600
250
600
250
600
TBD
TBD
TBD
250
250
250
250
250
250
250
TBD
TBD
TBD
250
250
250
250
250
250
250
TBD
TBD
TBD
Agency Current Rating (Single Circuit)
(Amps)
UL
CSA
IEC
N/A
N/A
N/A
N/A
N/A
N/A
N/A
TBD
TBD
TBD
7
7
5
5
5
5
5
TBD
TBD
TBD
5
5
5
5
5
5
5
TBD
TBD
TBD
(Current ratings are maximum and may vary depending on wire size, circuit count, and end-use
application. Further testing may be required in the end-use application.)
4.2 CURRENT DERATING AND APPLICABLE WIRES
Current is dependent on connector size, contact material, plating, ambient temperature, printed
circuit board characteristics and related factors. Actual current rating is application dependent
and should be evaluated for each application.
AWG
20
22
24
26
28
30
Max. Outside Insulation Diameter
1.85 mm (.073 inch)
1.85 mm (.073 inch)
1.85 mm (.073 inch)
1.27 mm (.050 inch)
1.27 mm (.050 inch)
1.27 mm (.050 inch)
REVISION:
TITLE:
EC No:
UCP2016-3198
DATE:
2016/02/17
L3
PRODUCT SPECIFICATION
Micro-Fit (3.0)
BMI Floating Connector System
CHECKED BY:
SHEET No.
2
of
12
F.SMITH
DOCUMENT NUMBER:
CREATED / REVISED BY:
APPROVED BY:
PS-44300-001
CSLAFTER
S.SOUSEK
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
CURRENT DERATING REFERENCE INFORMATION
2-circuit
W-W
AWG
20
22
24
26
28
30
1)
2)
3)
4)
5)
6)
Amps
6.5
5.5
5
4
3
3
W-B
Amps
7
*6
5.5
4.5
*4
3.5
6-circuit
W-W
Amps
5
*4
4
3
*2
2
W-B
Amps
* 5.5
* 4.5
* 4.5
*4
*3
*3
12-circuit
W-W
Amps
4.5
* 3.5
3
2.5
*2
2
W-B
Amps
*5
*4
* 3.5
* 3.5
*3
* 2.5
24-circuit
W-W
Amps
*4
*3
*2
* 1.5
*1
*1
W-B
Amps
4.5
* 3.5
*3
2.5
*2
1
Values are for REFERENCE ONLY.
Current deratings are based on not exceeding 30°C Temperature Rise.
PCB trace design can greatly affect temperature rise results in Wire-to-Board applications.
Data is for all circuits powered.
* indicates interpolated information.
W-W:
Wire-to-Wire
W-B:
Wire-to-Board
4.3 CURRENT FOR TEST PLUG 44242
2.5 Amps Maximum (Pogo pin current capacity)
(Test plugs are for testing purposes only and not intended for continuous use.)
4.4 TEMPERATURE
Operating:
-40°C to +105°C (Including Terminal Temperature Rise)
Nonoperating: -40°C to +105°C
REVISION:
TITLE:
EC No:
UCP2016-3198
DATE:
2016/02/17
L3
PRODUCT SPECIFICATION
Micro-Fit (3.0)
BMI Floating Connector System
CHECKED BY:
SHEET No.
3
of
12
F.SMITH
DOCUMENT NUMBER:
CREATED / REVISED BY:
APPROVED BY:
PS-44300-001
CSLAFTER
S.SOUSEK
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
5.0 PERFORMANCE
5.1 ELECTRICAL REQUIREMENTS
DESCRIPTION
Contact
Resistance
(Low Level)
Contact
Resistance of
Wire Termination
(Low Level)
Insulation
Resistance
Dielectric
Withstanding
Voltage
Capacitance
TEST CONDITION
Mate connectors: apply a maximum voltage
of 20 mV and a current of 100 mA.
Terminate the applicable wire to the terminal
and measure wire using a voltage of 20 mV
and a current of 100 mA.
Unmate & unmount connectors: apply a
voltage of 500 VDC between adjacent
terminals and between terminals to ground.
Unmate connectors: apply a voltage of {two
times the rated voltage plus 1000 volts} VAC
for 1 minute between adjacent terminals and
between terminals to ground.
Measure between adjacent terminals at 1
MHz.
REQUIREMENT
10 milliohms
MAXIMUM
[initial]
5 milliohms
MAXIMUM
[initial]
1000 Megohms
MINIMUM
No breakdown;
current leakage < 5 mA
2 picofarads
MAXIMUM
Mate connectors: measure the temperature
rise at the rated current after:
Temperature
1) 96 hours (steady state)
Rise
2) 240 hours (45 minutes ON and 15
(via Current Cycling)
minutes OFF per hour)
3) 96 hours (steady state)
5.2 MECHANICAL REQUIREMENTS
DESCRIPTION
Connector Mate
and
Unmate Forces
Crimp Terminal
Retention Force
(in Housing)
TEST CONDITION
Mate and unmate connector (male to female)
at a rate of 25 ± 6 mm (1 ± ¼ inch) per
minute. (per circuit)
Axial pullout force on the terminal in the
housing at a rate of 25 ± 6 mm (1 ± ¼ inch)
per minute.
Temperature rise:
+30°C MAXIMUM
REQUIREMENT
8.0 N (1.8 lbf)
MAXIMUM insertion force
&
2.4 N (0.5 lbf)
MINIMUM withdrawal force
24.5 N (5.5 lbf)
MINIMUM retention force
REVISION:
TITLE:
EC No:
UCP2016-3198
DATE:
2016/02/17
L3
PRODUCT SPECIFICATION
Micro-Fit (3.0)
BMI Floating Connector System
CHECKED BY:
SHEET No.
4
of
12
F.SMITH
DOCUMENT NUMBER:
CREATED / REVISED BY:
APPROVED BY:
PS-44300-001
CSLAFTER
S.SOUSEK
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
5.2 MECHANICAL REQUIREMENTS
DESCRIPTION
Pin
Retention Force
(in Header)
Crimp Terminal
Insertion Force
(into Housing)
Durability
TEST CONDITION
Apply axial pullout force on the terminal in the
housing at a rate of 25 ± 6 mm (1 ± ¼ inch)
per minute.
Apply an axial insertion force on the terminal
at a rate of 25 ± 6 mm (1 ± ¼ inch) per
minute.
Mate connectors up to 30 cycles for tin or
gold at a maximum rate of 10 cycles per
minute.
Mate connectors and vibrate per EIA 364-28,
test condition
VII.
REQUIREMENT
13.3 N (3.0 lbf)
MINIMUM retention force
14.7 N (3.3 lbf)
MAXIMUM insertion force
10 milliohms MAXIMUM
(change from initial)
10 milliohms MAXIMUM
(change from initial)
&
Discontinuity < 1 microsecond
10 milliohms MAXIMUM
(change from initial])
&
Discontinuity < 1 microsecond
20 Awg: 57.9 N (13.0 lbf)
22 Awg: 35.5 N (8.0 lbf)
24 Awg: 26.6 N (6.0 lbf)
26 Awg: 13.3 N (3.0 lbf)
28 Awg: 8.9 N (2.0 lbf)
30 Awg: 6.6 N (1.5 lbf)
MINIMUM pullout force
2.7 N (0.6 lbf) MINIMUM
Vibration
(Random)
Shock
(Mechanical)
Mate connectors and shock at 50 g's with ½
sine wave (11 milliseconds) shocks in the
±X,±Y,±Z axes (18 shocks total).
Wire
Pullout Force
(Axial)
Wire to Terminal
Apply an axial pullout force on the wire at a
rate of 25 ± 6 mm (1 ± ¼ inch).
Normal
Force
Panel Retention
Forces
Fretting
Corrosion
(Hammer Shock)
Compliant Pin
Insertion Force into
PCB Hole
(45280 Series)
Compliant Pin
Retention Force in
PCB Hole
(45280 Series)
REVISION:
Apply a perpendicular force.
Apply a force perpendicular to the panel on
the connector at a rate of 25 ± 6 mm (1 ± ¼
inch) per minute.
Mate connectors: strike test platform at a
rate of 10 cycles per minute with a 0.98 N
(100 gram) hammer for 20,000 cycles.
Apply an axial insertion force on the terminal
at a rate of 25 ± 6 mm (1 ± ¼ inch).
200 N (45 lbf)
MINIMUM withdrawal force
10 milliohms MAXIMUM
(change from initial)
106.7 N (24 lbf)
MAXIMUM Insertion force
(Per Terminal)
35.6 N (8 lbf)
MINIMUM Retention force
(Per Terminal)
Apply an axial extraction force on the
terminal at a rate of 25 ± 6 mm (1 ± ¼ inch).
TITLE:
EC No:
UCP2016-3198
DATE:
2016/02/17
L3
PRODUCT SPECIFICATION
Micro-Fit (3.0)
BMI Floating Connector System
CHECKED BY:
SHEET No.
5
of
12
F.SMITH
DOCUMENT NUMBER:
CREATED / REVISED BY:
APPROVED BY:
PS-44300-001
CSLAFTER
S.SOUSEK
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
京公网安备 11010802033920号
EEWORLD
