Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= 5V, V
BATT
= 4V, R
POK
= 1MΩ to BATT,
EN
= unconnected, R
SETI
= 2.8kΩ to GND, V
DETBAT
= 0, C
BATT
= 2.2µF, T
A
= -40°C to
+85°C, unless otherwise noted. Typical values are at T
Now I want to output the PWM signal through the HPWM tube of OMAP138, and then output it to the VCXO crystal oscillator through the active filter circuit, but I don’t know if anyone has done this befo...
[align=center][font=punctuation, 微软雅黑, Tohoma][size=12px][color=rgb(0, 0, 0)][font=微软雅黑][color=#000000][size=26px]Yuan Fang, what do you think of this circuit? (4) [/size][/color][/font][/color][/size...
[i=s]This post was last edited by ddllxxrr on 2014-6-22 22:24[/i] This mobile phone DIY has been going on for quite a while. My plan is to finish it in July, and now it seems almost done. Today is Sun...
In the era of touch screens dominating consumer electronics, how can oscilloscopes be mediocre? So, what will happen when it meets our engineers? Let's take a look at the video shot by EEWOLRD netizen...
Is there anyone who can give me some advice? ! Thank you
Multiple message objects of a CAN controller form a send FIFO or receive FIFO to send and receive CAN data. Compared with a single message obje...
I am designing an adapter board, which requires 100 to 160 pins. The PCI socket has 198 pins, but it is a bit large; the miniPCI socket is usually attached to the board, but I want one that is facing ...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Multimedia processors are often the most power-hungry devices in portable electronic devices. Common ways to reduce CPU power requirements are to reduce clock frequency or operating voltage, but th...[Details]
0 Introduction
The load with impact (rapid change) power in the power system will cause the voltage fluctuation and flicker of the power grid, causing many electrical equipment to fail to wo...[Details]
1. Sensor
According to the national standard GB7665-87, a sensor is defined as a device that can sense the specified measured quantity and convert it into a usable output signal according to a...[Details]
With the development of control, computer, communication and network technology, computer network integrated automation system has been widely used in modern industrial enterprises. The emergence o...[Details]
1. Introduction
Industrial fieldbus technology is one of the technologies that has received the most attention in the automation industry in recent years, and it has brought a qualitative leap...[Details]
Different places have accumulated certain experience in equalizing charging of battery packs, but it is difficult to master it properly. Long-term non-equalizing charging or frequent equalizing cha...[Details]
Typically, buck regulators are designed for continuous mode operation, which simplifies output voltage calculations and system design. However, if the system is non-synchronous and required to oper...[Details]
In recent years, the rapid development of high-performance digital signal processing chip DSP (Digital Signal Process) technology has made it possible to realize real-time speech recognition. Amo...[Details]
PIC microcontrollers are becoming increasingly popular in China. This article introduces some experiences and techniques in software and hardware design during the development of Microchip PIC seri...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
