EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4QV01EG-1153CDI

Description
Programmable Oscillators PROGRAMMABLE 5X7 OSCILLATOR
CategoryPassive components    oscillator   
File Size329KB,20 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N4QV01EG-1153CDI Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4QV01EG-1153CDI - - View Buy Now

8N4QV01EG-1153CDI Overview

Programmable Oscillators PROGRAMMABLE 5X7 OSCILLATOR

8N4QV01EG-1153CDI Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
Is SamacsysN
Manufacturer's serial numberIDT8N4QV01
Oscillator typeLVDS
Base Number Matches1
Quad-Frequency Programmable
VCXO
General Description
The IDT8N4QV01 is a Quad-Frequency Programmable VCXO with
very flexible frequency and pull-range programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 10-lead ceramic 5mm x
7mm x 1.55mm package.
Besides the 4 default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4QV01 can be programmed via the I
2
C
interface to any output clock frequency between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷N (N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to 4
independent PLL, P, M and N divider registers (P, MINT, MFRAC and
N), reprogramming those registers to other frequencies under
control of FSEL0 and FSEL1 is supported. The extended
temperature range supports wireless infrastructure, tele-
communication and networking end equipment requirements.
IDT8N4QV01 REV G
DATASHEET
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order codes),
re-programmable by I
2
C
I
2
C programming interface for the output clock frequency, APR
and internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
Absolute pull-range (APR) programmable from ±4.5ppm to
±754.5ppm
One 2.5V or 3.3V LVDS differential clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.494ps
(typical)
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.594ps (typical)
2.5V or 3.3V supply voltage modes
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) packaging
Block Diagram
OSC
114.285 MHz
÷MINT,
MFRAC
2
VC
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
÷N
Q
nQ
VC 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
A/D
7
25
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
7
IDT8N4QV01 REV G DATA SHEET
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4QV01GCD REVISION A MARCH 11, 2014
1
©2014 Integrated Device Technology, Inc.
When I use the Simulator in Tornado2.2, why do I always get the Simulator failed to initialize before timeout?
When I use the Simulator in Tornado2.2, why do I always get the error "Simulator failed to initialiaze before timeout!"? What should I do?...
jjww Embedded System
Golden advice on schematic drawing, starting with the interesting three-dimensional resistor network
We are not used to reading a schematic in 3D, so the first step is to redraw it clearly. There are three obvious paths from A to B, marked in blue, green and red. Each path has a series link 1Ω-R-1Ω. ...
maylove Analogue and Mixed Signal
【GD32L233C-START Review】2. Super Mario Run
[i=s] This post was last edited by bzhou830 on 2022-2-14 21:46 [/i] ## Preface In the previous article, I used the GD32L233C-START evaluation board to drive the LCD screen. Then I ran Super Mario on t...
bzhou830 GD32 MCU
STMicroelectronics once again strikes hard at the MCU market, launching its first batch of ultra-low-power 8-bit MCUs today
Without further ado, let me show you a few slides first, and then I will issue a press release.Experts can see the details, and laymen can also watch the fun. Comments are welcome._Slide9.GIF(56.92 KB...
1200324 stm32/stm8
Infrared decoding
Could any of you help me solve this problem: Why is the infrared decoding data I wrote always refreshing when I press the same key?...
w1989621w 51mcu
Has anyone done IO simulation UART but not using the timerA0 module?
Sorry, I am a beginner and I don't know much about MSP430. My boss wants me to use IO pins to make multiple UART functions. I see many people use capture/compare to do it but it has some limitations. ...
lavender780510 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 931  1061  2531  1761  258  19  22  51  36  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号