the chip accepts 25.0MHz from a crystal or a refer-
ence clock, and produces multiple outputs clocks for
network chips, PCI devices, SDRAM, and ASICs.
Note:
^: 100kΩ internal pull-up. *: Bi-directional pin. The value of
CS1 is latched upon power-up. When no external pull-down re-
sistor is connected to the pin, the internal pull-up results in a
default high value for CS1. An external 10kΩ pull-down resis-
tor is recommended to set CS1 to low.
BLOCK DIAGRAM
OE
XIN
XOUT
XTAL
OSC
REFOUT
CLKA1
CLKA2
FS (0:4)
Control
Logic
CS (0:1)
CLKB1
CLKB2
CLKC1
CLKC2
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 09/03/04 Page 1
PLL650-01
Low EMI Network LAN Clock
PIN DESCRIPTIONS
Name
CLKA1
CLKA2
CLKB1
CLKB2
CLKC1
CLKC2
XIN
XOUT
FS2
FS3
CS0
FS0
FS1
FS4
OE
REF/CS1
VDD
GND
Number
17
13
10
9
7
8
3
2
19
20
11
1
5
12
15
18
4,16
6,14
Type
O
O
O
O
O
O
I
O
I
I
I
I
I
I
I
B
P
P
Description
Clock A Output. Frequency Select pin selectable via (FS0 ~ FS4).
Clock A Output. Frequency Select pin selectable via (FS0 ~ FS4).
Clock B Output. Frequency Select pin selectable via (FS0 ~ FS4).
Clock B Output. Frequency Select pin selectable via (FS0 ~ FS4).
Clock C Output. Selectable from jumper CS0 and table CS1 output.
Clock C Output. Selectable from jumper CS0 and table CS1 output.
Crystal input to be connected to a fundamental crystal or clock input.
Crystal Connection.
Frequency Select 2. Select outputs per table on page 3.
Frequency Select 3. Select outputs per table on page 3.
Clock C select pin. Select outputs for CLKC1, CLKC2.
Frequency Select 0. Select outputs per table on page 3.
Frequency Select 1. Select outputs per table on page 3.
Frequency Select 4. Select outputs per table on page 3.
Output Enable. When low, Tri-states all outputs.
Buffered Reference Clock Outputs. Same frequency as crystal or clock input.
This pin latches CS1 value at power up and select outputs for CLKC1,
CLKC2 (See table on page 3). Has internal pull-up resistor.
3.3V power supply.
Ground.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 09/03/04 Page 2
PLL650-01
Low EMI Network LAN Clock
FREQUENCY (MHz) SELECTION TABLE (For a 25MHz Crystal or Clock Input)
FS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
FS1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
FS2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
FS3
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
FS4
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
CLKA1
100.0
100.0
100.0
100.0
75.0
75.0
75.0
66.667
33.333
33.333
33.333
33.333
66.667
66.667
66.667
66.667
100.0
100.0
133.333
133.333
133.333
133.333
133.333
100.0
100.0
125.0
83.333
125.0
Test
100.0
125.0
133.333
CLKA2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
16.667
16.667
16.667
16.667
33.333
33.333
33.333
33.333
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Test
OFF
OFF
OFF
CLKB1
66.667
100.0
83.333
133.333
66.667
100.0
83.333
133.333
66.667
100.0
83.333
133.333
66.667
100.0
83.333
133.333
OFF
OFF
OFF
OFF
66.667
66.667
66.667
100.0
100.0
OFF
83.333
OFF
Test
100.0
OFF
133.333
CLKB2
33.333
50.0
41.667
66.667
33.333
50.0
41.667
66.667
33.333
50.0
41.667
66.667
33.333
50.0
41.667
66.667
OFF
OFF
OFF
OFF
33.333
33.333
33.333
50.0
OFF
OFF
OFF
OFF
Test
OFF
OFF
OFF
SST*
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
±0.25%
±0.5%
±0.25%
±0.5%
±0.25%
±0.5%
OFF
±0.25%
OFF
±0.25%
±0.5%
OFF
Test
±0.25%
±0.5%
±0.25%
Note:
SST = Spread Spectrum Technology for EMI Reduction
CS1
0
0
1
1
CS0
0
1
0
1
CLKC1
125.0
75.0
125.0
100.0
CLKC2
125.0
75.0
50.0
OFF
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 09/03/04 Page 3
PLL650-01
Low EMI Network LAN Clock
FUNCTIONAL DESCRIPTION
Selectable spread spectrum and output frequencies
The PLL650-01 provides selectable spread spectrum modulation and selectable output frequencies, as well as an
“output enable” selection input (pin 15). Selection is made by connecting specific pins to a logical “zero” or “one”,
according to the frequency selection tables shown on page 3.
In order to reduce the number of pins on the chip, the PLL650-01 uses pin 18 (REF/CS1) as a bi-directional pin
that serves as input (CS1) upon power-up, and as output (REF) as soon as the input has been latched.
Pins 1 (FS0), 5 (FS1), 19 (FS2), 20 (FS3), and 12 (FS4) are used as inputs to select the CLKA1, CLKA2, CLKB1,
CLKB2 output frequencies and spread spectrum (SST) modulations (as detailed in the frequency selection table on
page 3). Pins 11 (CS0) and 18 (REF/CS1) are used to select the CLKC1 and CLKC2 frequency outputs. As said
above, pin 18 is a bi-directional pin.
Pin 15 (OE) is the output enable selection input that tri-states (disables) all outputs when selected to “low” (logical
“zero”).
Connecting a selection pin to a logical “one”
In order to connect pins 1 (FS0), 5 (FS1), 19 (FS2), 20 (FS3), and 12 (FS4) to “high” (logical “one), the pins simply
need to be connected to VDD. Pins 15 and 18 have an internal pull-up resistor of 100kΩ. This internal pull-up re-
sistor will pull the input value to a logical “one” (pull-up) by default, i.e. when no resistive load is connected be-
tween the pin and GND. For pins 15 and 18, no external pull-up resistor is therefore required for connecting a logi-
cal “one” upon.
Note:
since pin18 also is used as an output, it may happen that the output load present a low im-
pedance in comparison to the internal pull-up resistor. In this case, the internal pull-up resistor may not be suffi-
cient to pull the input up to a logical “one”, and an external pull-up resistor may be required.
Connecting a selection pin to a logical “zero”
Except for pin 18 (REF/CS1) that is bi-directional, all other input pins are input only. In order to connect them to a
logical “zero”, the pins simply need to be grounded. Connecting pin 18 to a logical “zero” will however require the
use of an external loading resistor between the pin and GND that has to be sufficiently small (compared to the in-
ternal pull-up resistor) so that the pin voltage be pulled below 0.8V (logical “zero”). In order to avoid loading effects
when the pin serves as output, the value of the external pull-down resistor should however be kept as large as
possible. In general, it is recommended to use an external resistor of around 10kΩ (see Application Diagram).
Note:
when the output is used to drive a load presenting an small resistance between the output pin and VDD, this
resistance is in essence connected in parallel to the internal pull-up resistor. In such a case, the external pull-down
resistor may have to be dimensioned smaller to guarantee that the pin voltage will be low enough to achieve the
desired logical “zero”. This is particularly true when driving 74FXX TTL components.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 09/03/04 Page 4
PLL650-01
Low EMI Network LAN Clock
APPLICATION DIAGRAM FOR SETTING CS1 (PIN 18)
Internal to chip
VDD
External Circuitry
R
up
Power Up
Reset
R
RB
Output
EN
REF/CS1
Clock Load
Latched
Input
Latch
10kΩ
Jumper options
NOTE:
Rup=100kΩ . R starts from 1 to 0 while RB starts from 0 to 1.
Electrical Specifications
1. Absolute Maximum Ratings
PARAMETERS
Supply Voltage
Input Voltage, dc
Output Voltage, dc
Storage Temperature
Ambient Operating Temperature*
Junction Temperature
Lead Temperature (soldering, 10s)
ESD Protection, Human Body Model
SYMBOL
V
DD
V
I
V
O
T
S
T
A
T
J
MIN.
-0.5
-0.5
-65
-40
MAX.
4.6
V
DD
+0.5
V
DD
+0.5
150
85
125
260
2
UNITS
V
V
V
°C
°C
°C
°C
kV
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the
device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other con-
ditions above the operational limits noted in this specification is not implied.
*
Note:
Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
Speaking of Raspberry Pi, I believe everyone has heard of it. In addition to being known as the world's cheapest card-type computer, the latest version Raspberry Pi 2 Model B also supports various Win...
MSP430F538 stepper motor driver control I recently need to use a five-phase stepper motor, but I have never used this stepper motor driver before. The driver uses CW and CCW inputs, which makes me dru...
input [1:0] in; // Define the input as 2-bit data output [1:0] out; //Define the output as 2-bit data reg [1:0] out; .... out={out,in}; //Use the concatenation operator. The input and output are both ...
I'm working on an LPC1769 board recently. I encountered some problems when I first started building a project. I tried for a long time and searched a lot of information on the Internet but couldn't so...
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
This article focuses on closing the feedback loop of an isolated power supply using a TL431 shunt regulator. The article discusses a method to extend the bandwidth of the power supply control loop ...[Details]
When developing electronic products with processors, how to improve anti-interference ability and electromagnetic compatibility?
1. The following systems should pay special attention to anti-...[Details]
introduction
Belt drive is a common transmission device used in industrial production. Its commonly used speed detection device is a photoelectric encoder installed at the rotating end of th...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
