Pin Voltage (Forced) .........................................5.5V
Maximum Operating Ambient Temperature Range
LT1176C/LT1176C-5 ................................. 0°C to 70°C
Maximum Operating Junction Temperature Range
LT1176C/LT1176C-5 ............................... 0°C to 125°C
Storage Temperature Range .................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................... 300°C
*These thermal resistance numbers are for typical mounting technique. Lower thermal
resistance can be obtained with large copper lands, thermal glues or heat sinks.
PIN CONFIGURATION
TOP VIEW
V
IN
1
TOP VIEW
V
IN
1
I
LIM
2
GND 3
FB/SENSE 4
8
7
6
5
V
SW
V
C
STATUS
SHUTDOWN
NC 2
I
LIM
3
GND 4
GND 5
GND 6
GND 7
NC 8
FB/SENSE 9
NC 10
20 V
SW
19 NC
18 V
C
17 GND
16 GND
15 GND
14 GND
13 STATUS
12 SHUTDOWN
11 NC
SW PACKAGE
20-LEAD PLASTIC SOL
T
JMAX
= 125°C,
θ
JA
= 50°C/W
N8 PACKAGE
8-LEAD PLASTIC DIP
T
JMAX
= 125°C,
θ
JA
= 90°C/W
ORDER INFORMATION
LEAD FREE FINISH
LT1176CN8#PBF
LT1176CN8-5#PBF
LT1176CSW#PBF
LT1176CSW-5#PBF
LT1176CSW#TRPBF
LT1176CSW-5#TRPBF
TAPE AND REEL
PART MARKING*
LT1176CN8
LT1176CN8-5
LT1176CSW
LT1176CSW-5
PACKAGE DESCRIPTION
8-Lead Plastic DIP
8-Lead Plastic DIP
20-Lead Plastic SOL
20-Lead Plastic SOL
TEMPERATURE RANGE
0°C to 125°C
0°C to 125°C
0°C to 125°C
0°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
11765fb
2
LT1176/LT1176-5
ELECTRICAL CHARACTERISTICS
PARAMETER
Switch ON Voltage (Note 2)
Switch OFF Leakage
Supply Current (Note 3)
Minimum Supply Voltage
Switch Current Limit (Note 5)
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. T
J
= 25°C, V
IN
25V, unless otherwise noted.
CONDITIONS
I
SW
= 0.2A
I
SW
= 1A
V
IN
= 25V, V
SW
= 0
V
IN
= V
MAX
, V
SW
= 0 (Note 8)
V
FB
= 2.5V, V
IN
≤ 35V
V
SHDN
= 0.1V (Device Shutdown) (Note 9)
Normal Mode
Startup Mode (Note 4)
I
LIM
Open
R
LIM
= 10k (Note 6)
R
LIM
= 7k (Note 6)
l
l
l
l
l
l
l
MIN
TYP
MAX
1.1
1.4
150
250
UNITS
V
V
µA
µA
mA
µA
V
V
A
A
A
%
kHz
kHz
kHz
kHz
%/V
V/V
µmho
µA
mA
µA
V
%
%
V
%
%
kΩ
%/V
V
mV/°C
V
7.5
140.0
7.3
3.5
1.2
1.7
1.2
0.8
90
100
20
20
0.03
2000
3700
5000
140
1.0
0.5
2.155
2.21
±0.5
±1.0
4.85
5
±0.5
±0.1
3
5
0.005
1.5
–4.0
24
5
2.2
0.1
±4
3.5
10
2.45
0.30
±5
4.5
10
300
8.0
4.8
2.2
Maximum Duty Cycle
Switching Frequency
l
l
85
90
85
V
FB
= 0V Through 2k (Note 5) (LT1176)
V
SENSE
= 0V (Note 5) (LT1176-5)
Switching Frequency Line Regulation
Error Amplifier Voltage Gain (Note 10)
Error Amplifier Transconductance (Note 10)
Error Amplifier Source and Sink Current
Feedback Pin Bias Current (LT1176)
Reference Voltage (LT1176)
Reference Voltage Tolerance (LT1176)
Source (V
FB
= 2V or V
SENSE
= 4V)
Sink (V
FB
= 2.5V or V
SENSE
= 5.5V)
V
FB
= V
REF
V
C
= 2V
V
REF
(Nominal) = 2.21V
All Conditions of Input Voltage, Output Voltage,
Temperature and Load Current
V
C
= 2V
V
OUT
(Nominal) = 5V
All Conditions of Input Voltage,
Temperature and Load Current
8V ≤ V
IN
≤ V
MAX
(Note 8)
Overtemperature
V
SHDN
= 5V
V
SHDN
≤ V
THRESHOLD
(@ 2.5V)
Switch Duty Cycle = 0
Fully Shutdown
As a Percent of Output Voltage
I
STATUS
= 10µA Sourcing
l
l
l
l
l
l
110
120
8V ≤ V
IN
≤ V
MAX
(Note 8)
1V ≤ V
C
≤ 4V
l
0.1
8000
225.0
1.6
2
2.265
±2
±3
5.15
±2
±3
8
0.02
100.0
0.7
Sense Voltage (LT1176-5)
Sense Voltage Tolerance (LT1176-5)
Sense Pin Divider Resistance (LT1176-5)
Output Voltage Line Regulation
V
C
Voltage at 0% Duty Cycle
Multiplier Reference Voltage
Shutdown Pin Current
Shutdown Thresholds
Status Window
Status High Level
l
l
l
l
l
l
20
50
2.7
0.5
±6
5.0
µA
µA
V
V
%
V
11765fb
3
LT1176/LT1176-5
ELECTRICAL CHARACTERISTICS
PARAMETER
Status Low Level
Status Delay Time
Status Minimum Width
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
To calculate maximum switch ON voltage at current between low
and high conditions, a linear interpolation may be used.
Note 3:
A feedback pin voltage (V
FB
) of 2.5V forces the V
C
pin to its low
clamp level and the switch duty cycle to zero. This approximates the
zero load condition where duty cycle approaches zero. The LT1176-5 has
V
SENSE
= 5.5V.
Note 4:
Total voltage from V
IN
pin to ground pin must be ≥ 8V after
start-up for proper regulation.
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. T
J
= 25°C, V
IN
25V, unless otherwise noted.
CONDITIONS
I
STATUS
= 1.6mA Sinking
l
MIN
TYP
0.25
9
30
MAX
0.4
UNITS
V
µs
µs
Note 5:
Switch frequency is internally scaled down when the feedback pin
voltage is less than 1.3V to avoid extremely short switch-on times. During
testing, V
FB
or V
SENSE
is adjusted to give a minimum switch-on time of
1µs.
Note 6:
I
LM
= (R
LIM
– 1k)/7.65k
Note 7:
Switch to input voltage limitation must also be observed.
Note 8:
V
MAX
= 35V
Note 9:
Does not include switch leakage.
Note 10:
Error amplifier voltage gain and transconductance are
specified relative to the internal feedback node. To calculate gain and
transconductance from the sense pin (Output) to the V
C
pin on the
LT1176-5, multiply by 0.44.
Application Hints
Although the LT1176 has a peak switch rating of 1.2A and a maximum duty
cycle of 85%, it must be used cautiously in applications which require high
switch current and high duty cycle simultaneously, to avoid excessive chip
temperature. Thermal resistance is 90°C/W for the 8-pin DIP package and
50°C/W for the 20-pin SO. This limits continuous chip power dissipation to
the 0.5W to 1W range. These numbers assume typical mounting techniques.
Extra or thick copper connected to the leads can reduce thermal resistance.
Bonding the package to the board or using a clip style heat sink can also help.
The following formulas will give chip power dissipation and peak switch current
for the standard buck converter. Note that surges less than 30 seconds do not
need to be considered from a thermal standpoint, but for proper regulation,
they must not result in peak switch currents exceeding the 1.2A limit.
Power = I
LOAD
(V
OUT
/V
IN
) + V
IN
[7mA + 3mA (V
OUT
/V
IN
) + 0.012 (I
LOAD
)]
I
PEAK
= I
LOAD(PEAK)
+ [V
OUT
(V
IN
– V
OUT
)]/2E
5
(V
IN
)(L)
Example: V
IN
= 15V, V
OUT
= 5V, I
LOAD
= 0.5A Continuous, 0.8A Peak,
L = 100µH
Power (I
LOAD
= 0.5A) = 0.38W
I
PEAK
(I
LOAD
= 0.8A) = 0.97A
Where component size or height is critical, we suggest using solid tantalum
capacitors (singly or in parallel), but be sure to use units rated for switching
applications. Coiltronics is a good source for low profile surface mount
inductors and AVX makes high quality surface mount tantalum capacitors. For
further help, use Application Notes 19 and 44,LTC’s SwitcherCAD
®
computer
design program, and our knowledgeable application department.
The analysis report of iSuppli, a market research company, pointed out that with the widespread recovery of the electronic equipment market, the market for power management semiconductor devices has g...
The design of the desk lamp power supply takes into account the input DC9V of the desk lamp. In addition to designing the power supply as a constant current source, the light should also be selected a...
RT, data transfer between application and driver can be realized by readfile, writefile, but now I want to transfer a large amount of data by memory sharing. I don't know if shared memory between appl...
typedef struct userinfo { char[10] username; //User name long user_serial; //User identification number float user_fee; //User consumption amount, two decimal places} a; 1. A char is stored as 8 bits....
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
introduction
The emergence of high-performance, low-power embedded CPUs and high-reliability network operating systems has made it possible to implement applications with large amounts of comp...[Details]
1. Background:
The instrument system parameter detection and control of the chemical production workshop of Tangshan Coal Gas Coking Plant are all analog instruments, some of which are eve...[Details]
1 Introduction
Water resources are the basic conditions for human survival and the lifeline of economic development. The reality shows that due to the global shortage of water resources and th...[Details]
To understand how and why OLED power supply affects display image quality, you must first understand OLED display technology and power supply requirements. This article will explain the latest OLED...[Details]
introduction
Incandescent bulbs can emit a variety of light, but in specific applications, only green, red, and yellow light are usually needed - such as traffic lights. If an incand...[Details]
The emergence and development of street lamps are inseparable from the prosperity and progress of cities, which makes street lamps useful. Conversely, street lamps also make the night of the city n...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
In recent years, with the increasing maturity of LED technology, LED light sources have been increasingly widely used due to their advantages of using low-voltage power supply, low energy consumpti...[Details]
Dual Tone MultiFrequency (DTMF) signaling is gradually being used in push-button telephones around the world. It quickly replaced the dial pulse signaling used in traditional rotary phones because ...[Details]
1. Project Introduction
Beijing Benz-Daimler Chrysler Co., Ltd. is a joint venture between Beijing BAIC Group and Benz-Daimler Chrysler. In October 2005, it started to build a new automobile ...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
