The AS7C1026A and AS7C31026A are high-performance CMOS 1,048,576-bit Static Random Access Memory (SRAM) devices organized as
65,536 words × 16 bits. They are designed for memory applications where fast data access, low power, and simple interfacing are desired.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 3/3/4/5 ns are ideal for
high-performance applications.
When CE is high the devices enter standby mode. The AS7C1026A is guaranteed not to exceed 55 mW power consumption in CMOS
standby mode. The devices also offer 2.0V data retention.
A write cycle is accomplished by asserting write enable (WE) and chip enable (CE). Data on the input pins I/O0–I/O15 is written on the
rising edge of WE (write cycle 1) or CE (write cycle 2). To avoid bus contention, external devices should drive I/O pins only after outputs
have been disabled with output enable (OE) or write enable (WE).
A read cycle is accomplished by asserting output enable (OE) and chip enable (CE), with write enable (WE) high. the chips drive I/O pins
with the data word referenced by the input address. When either chip enable or output enable is inactive, or write enable is active, output
drivers stay in high-impedance mode.
The devices provide multiple center power and ground pins, and separate byte enable controls, allowing individual bytes to be written and
read. LB controls the lower bits, I/O0–I/O7, and UB controls the higher bits, I/O8–I/O15.
All chip inputs and outputs are TTL-compatible, and operation is from a single 5V supply (AS7C1026A) or 3.3V supply (AS7C31026A). the
device is packaged in common industry standard packages. Chip scale BGA packaging, easy to use in manufacturing, provides the smallest
possible footprint. This 48-ball JEDEC-registered package has a ball pitch of 0.75 mm and external dimensions of 8 mm × 6 mm.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature (plastic)
Ambient temperature with VCC
applied
DC current into outputs (low)
AS7C1026A
AS7C31026A
Both
Both
Both
Both
Both
Symbol
V
t1
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.50
–0.50
–0.50
–
–65
–55
–
Max
+7.0
+5.0
V
CC
+0.50
1.0
+150
+125
20
Unit
V
V
V
W
°C
°C
mA
Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect reliability.
Truth table
CE
H
L
L
L
L
L
L
L
L
WE
X
H
H
H
L
L
L
H
X
OE
X
L
L
L
X
X
X
H
X
LB
X
L
H
L
L
L
H
X
H
UB
X
H
L
L
L
H
L
X
H
I/O0–I/O7 I/O8–I/O15
High Z
D
OUT
High Z
D
OUT
D
IN
D
IN
High Z
High Z
High Z
High Z
D
OUT
D
OUT
D
IN
High Z
D
IN
High Z
Mode
Standby (I
SB
), I
SBI
)
Read I/O0–I/O7 (I
CC
)
Read I/O8–I/O15 (I
CC)
Read I/O0–I/O15 (I
CC
)
Write I/O0–I/O15 (I
CC
)
Write I/O0–I/O7 (I
CC
)
Write I/O8–I/O15 (I
CC
)
Output disable (I
CC
)
Key:
H = High, L = Low, X = don’t care.
2/6/01; V.0.9
Alliance Semiconductor
P. 2 of 9
®
AS7C1026A
AS7C31026A
Recommended operating conditions
Parameter
Supply voltage
Device
AS7C1026A
AS7C31026A
AS7C1026A
AS7C31026A
Both
commercial
industrial
Symbol
V
CC
V
CC
V
IH
V
IH
V
IL†
T
A
T
A
Min
4.5
3.0
2.2
2.0
–0.5
0
–40
Nominal
5.0
3.3
–
–
–
–
–
Max
5.5
3.6
V
CC
+ 0.5
V
CC
+ 0.5
0.8
70
85
Unit
V
V
V
V
V
o
C
o
C
Input voltage
Ambient operating temperature
†
V
IL
min. = –3.0V for pulse width less than t
RC
/2.
DC operating characteristics (over the operating range)
How is this upper computer software made? Can anyone tell me what software is used to make it?
It would be best if you could provide a software download link. How was this brother monitoring module de...
The amplifier input is a normal square wave, is the output like this normal? Can the spike be removed during level conversion? ? ? ? ? ? ? ? Waiting online urgently! ! ! !...
I am new to USB and developing a USB enabled embedded device for a client who designs hardware. The target is the STM32F4. The use case is that this device A) when connected to a computer, should appe...
xStatus_CAN= xQueueReceive( xQueue_CAN, &CAN_QUEUE_RECEIVE, portMAX_DELAY); If a task waits for message queue data and uses blocking waiting without timeout limit, will this task be suspended to allow...
"Brushless motors are gradually replacing heavier, noisier and less reliable brushed motors. Although brushless, stepper or sensorless motors require more complex control, they can provide better ener...
I read in a switching power supply learning book that "selecting a rectifier with a larger rated current can obtain a lower forward voltage drop, thereby reducing the power loss of the rectifier."
My ...
GD32 MCU
京公网安备 11010802033920号
EEWORLD
