The AS7C1026A and AS7C31026A are high-performance CMOS 1,048,576-bit Static Random Access Memory (SRAM) devices organized as
65,536 words × 16 bits. They are designed for memory applications where fast data access, low power, and simple interfacing are desired.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 3/3/4/5 ns are ideal for
high-performance applications.
When CE is high the devices enter standby mode. The AS7C1026A is guaranteed not to exceed 55 mW power consumption in CMOS
standby mode. The devices also offer 2.0V data retention.
A write cycle is accomplished by asserting write enable (WE) and chip enable (CE). Data on the input pins I/O0–I/O15 is written on the
rising edge of WE (write cycle 1) or CE (write cycle 2). To avoid bus contention, external devices should drive I/O pins only after outputs
have been disabled with output enable (OE) or write enable (WE).
A read cycle is accomplished by asserting output enable (OE) and chip enable (CE), with write enable (WE) high. the chips drive I/O pins
with the data word referenced by the input address. When either chip enable or output enable is inactive, or write enable is active, output
drivers stay in high-impedance mode.
The devices provide multiple center power and ground pins, and separate byte enable controls, allowing individual bytes to be written and
read. LB controls the lower bits, I/O0–I/O7, and UB controls the higher bits, I/O8–I/O15.
All chip inputs and outputs are TTL-compatible, and operation is from a single 5V supply (AS7C1026A) or 3.3V supply (AS7C31026A). the
device is packaged in common industry standard packages. Chip scale BGA packaging, easy to use in manufacturing, provides the smallest
possible footprint. This 48-ball JEDEC-registered package has a ball pitch of 0.75 mm and external dimensions of 8 mm × 6 mm.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature (plastic)
Ambient temperature with VCC
applied
DC current into outputs (low)
AS7C1026A
AS7C31026A
Both
Both
Both
Both
Both
Symbol
V
t1
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.50
–0.50
–0.50
–
–65
–55
–
Max
+7.0
+5.0
V
CC
+0.50
1.0
+150
+125
20
Unit
V
V
V
W
°C
°C
mA
Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect reliability.
Truth table
CE
H
L
L
L
L
L
L
L
L
WE
X
H
H
H
L
L
L
H
X
OE
X
L
L
L
X
X
X
H
X
LB
X
L
H
L
L
L
H
X
H
UB
X
H
L
L
L
H
L
X
H
I/O0–I/O7 I/O8–I/O15
High Z
D
OUT
High Z
D
OUT
D
IN
D
IN
High Z
High Z
High Z
High Z
D
OUT
D
OUT
D
IN
High Z
D
IN
High Z
Mode
Standby (I
SB
), I
SBI
)
Read I/O0–I/O7 (I
CC
)
Read I/O8–I/O15 (I
CC)
Read I/O0–I/O15 (I
CC
)
Write I/O0–I/O15 (I
CC
)
Write I/O0–I/O7 (I
CC
)
Write I/O8–I/O15 (I
CC
)
Output disable (I
CC
)
Key:
H = High, L = Low, X = don’t care.
2/6/01; V.0.9
Alliance Semiconductor
P. 2 of 9
®
AS7C1026A
AS7C31026A
Recommended operating conditions
Parameter
Supply voltage
Device
AS7C1026A
AS7C31026A
AS7C1026A
AS7C31026A
Both
commercial
industrial
Symbol
V
CC
V
CC
V
IH
V
IH
V
IL†
T
A
T
A
Min
4.5
3.0
2.2
2.0
–0.5
0
–40
Nominal
5.0
3.3
–
–
–
–
–
Max
5.5
3.6
V
CC
+ 0.5
V
CC
+ 0.5
0.8
70
85
Unit
V
V
V
V
V
o
C
o
C
Input voltage
Ambient operating temperature
†
V
IL
min. = –3.0V for pulse width less than t
RC
/2.
DC operating characteristics (over the operating range)
Please explain in detail what you want to design around this chip, or you can start drawing the schematic diagram.For detailed applications with circuit diagrams, or friends who actively upload materi...
The reference scheme in the radio magazine - Wei Kun has uploaded it in the first floor of this post [url=https://bbs.eeworld.com.cn/thread-74695-1-1.html]https://bbs.eeworld.com.cn/thread-74695-1-1.h...
The requirements are as follows: The actual fixed PCB space is limited (PCB is fixed inside the device), and the network cable needs to be led out to the outside. At present, I don’t want to put an RJ...
I recently used Cadence simulation to build a differential circuit. As long as the differential signal is connected in series with a capacitor, the amplitude of its DC component will be different. Can...
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
