ATMEGA323L-4AI datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > semiconductor> The embedded processor and controller> ATMEGA323L-4AI

ATMEGA323L-4AI: DescriptionIC MCU 8BIT 32KB FLASH 44TQFP; Categorysemiconductor The embedded processor and controller; File Size3MB，247 Pages; ManufacturerMicrochip; Websitehttps://www.microchip.com

Download Datasheet Parametric Compare View All

ATMEGA323L-4AI Overview

IC MCU 8BIT 32KB FLASH 44TQFP

ATMEGA323L-4AI Parametric

Parameter Name	Attribute value
core processor	AVR
core size	8-bit
speed	4MHz
Connectivity	I²C，SPI，UART/USART
Peripheral	Undervoltage detection/reset, POR, PWM, WDT
Number of I/Os	32
Program storage capacity	32KB（16K x 16）
Program memory type	flash memory
EEPROM capacity	1K x 8
RAM capacity	2K x 8
Voltage - Power Supply (Vcc/Vdd)	2.7 V ~ 5.5 V
data converter	A/D 8x10b
Oscillator type	internal
Operating temperature	-40°C ~ 85°C
Package/casing	44-TQFP
Supplier device packaging	44-TQFP（10x10）

Preview

Download Datasheet

View All

Features

•

High-performance, Low-power AVR

8-bit Microcontroller

•

Advanced RISC Architecture

– 130 Powerful Instructions – Most Single-clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

– Up to 8 MIPS Throughput at 8 MHz

– On-chip 2-cycle Multiplier

Non-volatile Program and Data Memories

– 32K Bytes of In-System Self-programmable Flash

Endurance: 1,000 Write/Erase Cycles

– Optional Boot Code Section with Independent Lock Bits

In-System Programming by On-chip Boot Program

– 1K Byte EEPROM

Endurance: 100,000 Write/Erase Cycles

– 2K Bytes Internal SRAM

– Programming Lock for Software Security

JTAG (IEEE Std. 1149.1 Compliant) Interface

– Extensive On-chip Debug Support

– Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface

– Boundary-Scan Capabilities According to the JTAG Standard

Peripheral Features

– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode

– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture

Mode

– Real Time Counter with Separate Oscillator

– Four PWM Channels

– 8-channel, 10-bit ADC

– Byte-oriented Two-wire Serial Interface

– Programmable Serial USART

– Master/Slave SPI Serial Interface

– Programmable Watchdog Timer with Separate On-chip Oscillator

– On-chip Analog Comparator

Special Microcontroller Features

– Power-on Reset and Programmable Brown-out Detection

– Internal Calibrated RC Oscillator

– External and Internal Interrupt Sources

– Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby

and Extended Standby

I/O and Packages

– 32 Programmable I/O Lines

– 40-pin PDIP and 44-lead TQFP

Operating Voltages

– 2.7 - 5.5V (ATmega323L)

– 4.0 - 5.5V (ATmega323)

Speed Grades

– 0 - 4 MHz (ATmega323L)

– 0 - 8 MHz (ATmega323)

•

8-bit

Microcontroller

with 32K Bytes

of In-System

Programmable

Flash

ATmega323

ATmega323L

Not recommended

for new designs.

Use ATmega32.

•

1457G–AVR–09/03

The AVR core combines a rich instruction set with 32 general purpose working registers.

All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing

two independent registers to be accessed in one single instruction executed in one clock

cycle. The resulting architecture is more code efficient while achieving throughputs up to

ten times faster than conventional CISC microcontrollers.

The ATmega323 provides the following features: 32K bytes of In-System Programmable

Flash, 1K bytes EEPROM, 2K bytes SRAM, 32 general purpose I/O lines, 32 general

purpose working registers, a JTAG interface for Boundary-Scan, On-chip Debugging

support and programming, three flexible Timer/Counters with compare modes, internal

and external interrupts, a serial programmable USART, a byte oriented Two-wire Serial

Interface, an 8-channel, 10-bit ADC, a programmable Watchdog Timer with internal

Oscillator, an SPI serial port, and six software selectable power saving modes. The Idle

mode stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt

system to continue functioning. The Power-down mode saves the register contents but

freezes the Oscillator, disabling all other chip functions until the next interrupt or Hard-

ware Reset. In Power-save mode, the asynchronous timer continues to run, allowing the

user to maintain a timer base while the rest of the device is sleeping. The ADC Noise

Reduction mode stops the CPU and all I/O modules except asynchronous timer and

ADC, to minimize switching noise during ADC conversions. In Standby mode, the crys-

tal/resonator Oscillator is running while the rest of the device is sleeping. This allows

very fast start-up combined with low-power consumption. In Extended Standby mode,

both the main Oscillator and the asynchronous timer continue to run.

The device is manufactured using Atmel’s high-density non-volatile memory technology.

The On-chip ISP Flash allows the Program memory to be re-programmed In-System

through an SPI serial interface, by a conventional non-volatile memory programmer, or

by an On-chip Boot Program running on the AVR core. The Boot Program can use any

interface to download the application program in the Application Flash memory. By com-

bining an 8-bit RISC CPU with In-System Programmable Flash on a monolithic chip, the

Atmel ATmega323 is a powerful microcontroller that provides a highly flexible and cost

effective solution to many embedded control applications.

The ATmega323 AVR is supported with a full suite of program and system development

tools including: C compilers, macro assemblers, program debugger/simulators, In-Cir-

cuit Emulators, and evaluation kits.

Pin Descriptions

VCC

GND

Port A (PA7..PA0)

Digital supply voltage.

Digital ground.

Port A serves as the analog inputs to the A/D Converter.

Port A also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used.

Port pins can provide internal pull-up resistors (selected for each bit). The Port A output

buffers can sink 20 mA and can drive LED displays directly. When pins PA0 to PA7 are

used as inputs and are externally pulled low, they will source current if the internal pull-

up resistors are activated. The Port A pins are tri-stated when a reset condition

becomes active, even if the clock is not running.

ATmega323(L)

1457G–AVR–09/03

ATmega323(L)

Port B (PB7..PB0)

Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each

bit). The Port B output buffers can sink 20 mA. As inputs, Port B pins that are externally

pulled low will source current if the pull-up resistors are activated. The Port B pins are

tri-stated when a reset condition becomes active, even if the clock is not running.

Port B also serves the functions of various special features of the ATmega323 as listed

on page 139.

Port C (PC7..PC0)

Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each

bit). The Port C output buffers can sink 20 mA. As inputs, Port C pins that are externally

pulled low will source current if the pull-up resistors are activated. The Port C pins are

tri-stated when a reset condition becomes active, even if the clock is not running.

Port C also serves the functions of the JTAG interface and other special features of the

ATmega323 as listed on page 146. If the JTAG interface is enabled, the pull-up resistors

on pins PC5 (TDI), PC3 (TMS) and PC2 (TCK) will be activated even if a Reset occurs.

Port D (PD7..PD0)

Port D is an 8-bit bidirectional I/O port with internal pull-up resistors (selected for each

bit). The Port D output buffers can sink 20 mA. As inputs, Port D pins that are externally

pulled low will source current if the pull-up resistors are activated. The Port D pins are

tri-stated when a reset condition becomes active, even if the clock is not running.

Port D also serves the functions of various special features of the ATmega323 as listed

on page 151.

RESET

Reset input. A low level on this pin for more than 500 ns will generate a Reset, even if

the clock is not running. Shorter pulses are not guaranteed to generate a Reset.

Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.

Output from the inverting Oscillator amplifier.

AVCC is the supply voltage pin for Port A and the A/D Converter. It should be externally

connected to V

, even if the ADC is not used. If the ADC is used, it should be con-

nected to V

through a low-pass filter. See page 127 for details on operation of the

ADC.

AREF is the analog reference pin for the A/D Converter. For ADC operations, a voltage

in the range 2.56V to AVCC can be applied to this pin.

Analog ground. If the board has a separate analog ground plane, this pin should be con-

nected to this ground plane. Otherwise, connect to GND.

XTAL1

XTAL2

AVCC

AREF

AGND

1457G–AVR–09/03

ATMEGA323L-4AI Related Products

	ATMEGA323L-4AI	ATMEGA323L-4PC	ATMEGA323L-4PI	ATMEGA323-8AC	ATMEGA323-8AI	ATMEGA323-8PC	ATMEGA323-8PI	ATMEGA323L-4AC
Description	IC MCU 8BIT 32KB FLASH 44TQFP	IC MCU 8BIT 32KB FLASH 40DIP	IC MCU 8BIT 32KB FLASH 40DIP	IC MCU 8BIT 32KB FLASH 44TQFP	IC MCU 8BIT 32KB FLASH 44TQFP	IC MCU 8BIT 32KB FLASH 40DIP	IC MCU 8BIT 32KB FLASH 40DIP	IC MCU 8BIT 32KB FLASH 44TQFP
core processor	AVR	AVR	AVR	AVR	AVR	AVR	AVR	AVR
core size	8-bit	8-bit	8-bit	8-bit	8-bit	8-bit	8-bit	8-bit
speed	4MHz	4MHz	4MHz	8MHz	8MHz	8MHz	8MHz	4MHz
Connectivity	I²C，SPI，UART/USART	I²C，SPI，UART/USART	I²C，SPI，UART/USART	I²C，SPI，UART/USART	I²C，SPI，UART/USART	I²C，SPI，UART/USART	I²C，SPI，UART/USART	I²C，SPI，UART/USART
Peripheral	Undervoltage detection/reset, POR, PWM, WDT	Undervoltage detection/reset, POR, PWM, WDT	Undervoltage detection/reset, POR, PWM, WDT	Undervoltage detection/reset, POR, PWM, WDT	Undervoltage detection/reset, POR, PWM, WDT	Undervoltage detection/reset, POR, PWM, WDT	Undervoltage detection/reset, POR, PWM, WDT	Undervoltage detection/reset, POR, PWM, WDT
Number of I/Os	32	32	32	32	32	32	32	32
Program storage capacity	32KB（16K x 16）	32KB（16K x 16）	32KB（16K x 16）	32KB（16K x 16）	32KB（16K x 16）	32KB（16K x 16）	32KB（16K x 16）	32KB（16K x 16）
Program memory type	flash memory	flash memory	flash memory	flash memory	flash memory	flash memory	flash memory	flash memory
EEPROM capacity	1K x 8	1K x 8	1K x 8	1K x 8	1K x 8	1K x 8	1K x 8	1K x 8
RAM capacity	2K x 8	2K x 8	2K x 8	2K x 8	2K x 8	2K x 8	2K x 8	2K x 8
Voltage - Power Supply (Vcc/Vdd)	2.7 V ~ 5.5 V	2.7 V ~ 5.5 V	2.7 V ~ 5.5 V	4.5 V ~ 5.5 V	4.5 V ~ 5.5 V	4.5 V ~ 5.5 V	4.5 V ~ 5.5 V	2.7 V ~ 5.5 V
data converter	A/D 8x10b	A/D 8x10b	A/D 8x10b	A/D 8x10b	A/D 8x10b	A/D 8x10b	A/D 8x10b	A/D 8x10b
Oscillator type	internal	internal	internal	internal	internal	internal	internal	internal
Operating temperature	-40°C ~ 85°C	0°C ~ 70°C	-40°C ~ 85°C	0°C ~ 70°C	-40°C ~ 85°C	0°C ~ 70°C	-40°C ~ 85°C	0°C ~ 70°C
Package/casing	44-TQFP	40-DIP（0.600"，15.24mm）	40-DIP（0.600"，15.24mm）	44-TQFP	44-TQFP	40-DIP（0.600"，15.24mm）	40-DIP（0.600"，15.24mm）	44-TQFP
Supplier device packaging	44-TQFP（10x10）	40-PDIP	40-PDIP	44-TQFP（10x10）	44-TQFP（10x10）	40-PDIP	40-PDIP	44-TQFP（10x10）

Recommended Resources

As a qualified engineer, you need to remember these circuit diagrams throughout your life!

FM intermediate frequency amplifier circuit

Applications to change output voltage polarity (a)

ADC701 simple block diagram

KA78R05, 12 typical application circuit diagram

Four sample-hold circuit diagram

What does [excluded from build] mean?: I wrote a simple IIC driver using PB5. It compiled OK. And the compiled iic.dll file has been added to the kernel. But in the FileView column of PB, there is [excluded from build] after Driver -> IIC....; wlzwlz777 Embedded System

I have resources to upload, but it's so slow~~~: I have resources to upload, but it's so slow~~~ Why is it so slow to upload a 1M resource? It took me several hours to finish, and finally it said that the verification code was wrong~~~ I feel dizzy~...; 999ljw Embedded System

msp430F249 program problem: #include "msp430F249.h" #define uchar unsigned char #define uint unsigned int #define NUM 16; long data; uint new_cap=0; uint old_cap=0; uint N1=0; char tab[]={0xc0,0xf9,0xA4,0XB0,0X99,0X92,0X82,0XF8,...; 步枪 Microcontroller MCU

PCB technology: several solutions for mounting SMD on FPC: According to the requirements of mounting accuracy and the types and quantities of components, the commonly used solutions are as follows: Solution 1, multi-piece mounting: multiple FPCs are positione...; ESD技术咨询 PCB Design

Guess: What is the origin of the code name of the open source "Wanli" Raspberry Pi car that went viral yesterday?: When I came to the forum yesterday, I found that @lb8820265 , who had not appeared in the arena for a long time, had a burst of updates, 12 updates, screen-sweeping style~Each title has the "Wanli" Ra...; nmg DIY/Open Source Hardware

The road ahead for CPU IP latecomers is long and arduous, and we will continue to explore: Currently, the annual shipment of 8-bit MCUs is 5 billion, and the shipment of 32-bit MCUs has exceeded 2 billion. According to the latest research report of IDC, by 2015, the smart systems of modern ...; 思潇 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components