Any frequency between 1 and 80 MHz accurate to 6 decimal places
100% pin-to-pin drop-in replacement to quartz-based (VC)TCXO
Frequency stability as low as ±5 ppm. Contact SiTime for tighter
stability options
Ultra low phase jitter: 0.5 ps (12 kHz to 20 MHz)
Voltage control option with pull range from ±12.5 ppm to ±50 ppm
LVCMOS compatible output with SoftEdge
™
option for EMI reduction
Voltage control, standby, output enable or no connect modes
Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, 7.0 x 5.0 mm
Outstanding silicon reliability of 2 FIT, 10 times better than quartz
Pb-free, RoHs and REACH compliant
WiFi, 3G, LTE, SDI, Ethernet, SONET, DSL
Telecom, networking, smart meter, wireless, test instrumentation
Electrical Characteristics
Parameter
Output Frequency Range
Initial Tolerance
Stability Over Temperature
Symbol
f
F_init
F_stab
Min.
1
-1
-5
Typ.
–
–
–
Max.
80
1
+5
Unit
MHz
ppm
ppm
At 25°C after two reflows
Over operating temperature range at rated nominal power
supply voltage and load. (see
ordering codes on page 6)
Contact SiTime for tighter stability options.
Supply Voltage
Output Load
First year Aging
10-year Aging
Operating Temperature Range
Supply Voltage
T_use
Vdd
F_vdd
F_load
F_aging
–
–
-2.5
-4.0
-20
-40
1.71
2.25
2.52
2.70
2.97
Pull Range
Upper Control Voltage
Control Voltage Range
Control Voltage Input Impedance
Frequency Change Polarity
Control Voltage -3dB Bandwidth
Current Consumption
OE Disable Current
Standby Current
Duty Cycle
LVCMOS Rise/Fall Time
SoftEdge™ Rise/Fall Time
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VOH
VOL
VIH
VIL
Z_in
PR
VC_U
VC_L
Z_vc
–
V_BW
Idd
I_OD
I_std
DC
Tr, Tf
–
–
–
–
–
–
–
45
–
90%
–
70%
–
–
Vdd-0.1
–
100
50
0.1
–
–
–
–
1.8
2.5
2.8
3.0
3.3
±12.5, ±25, ±50
–
–
–
Positive slope
–
31
29
–
–
–
–
–
1.5
–
–
–
–
100
8
33
31
31
30
70
10
55
2
–
10%
–
30%
250
–
0.1
–
–
–
+2.5
+4.0
+70
+85
1.89
2.75
3.08
3.3
3.63
ppb
ppm
ppm
ppm
°C
°C
V
V
V
V
V
ppm
V
V
k
–
kHz
mA
mA
mA
mA
µA
µA
%
ns
ns
Vdd
Vdd
Vdd
Vdd
k
No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V.
No load condition, f = 20 MHz, Vdd = 1.8V.
Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled Down
Condition
±10% Vdd (±5% for Vdd = 1.8V)
15 pF ±10% of load
25°C
25°C
Extended Commercial
Industrial
Contact SiTime for any other supply voltage options.
All Vdds. Voltage at which maximum deviation is guaranteed.
Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down
Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled Down.
Vdd = 1.8V. ST = GND, output is Weakly Pulled Down.
All Vdds
LVCMOS option. Default rise/fall time, All Vdds, 10% - 90% Vdd.
SoftEdge™ option. Frequency and supply voltage dependent.
OH = -7 mA, IOL = 7 mA, (Vdd = 3.3V, 3.0V)
IOH = -4 mA, IOL = 4 mA, (Vdd = 2.8V, 2.5V)
IOH = -2 mA, IOL = 2 mA, (Vdd = 1.8V)
Pin 1, OE or ST
Pin 1, OE or ST
SoftEdge™ Rise/Fall Time Table
SiTime Corporation
Rev. 1.0
990 Almanor Avenue
Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised November 12, 2015
SiT5001
1-80 MHz MEMS TCXO and VCTCXO
The Smart Timing Choice
The Smart Timing Choice
Electrical Characteristics (continued)
Parameter
Startup Time
OE Enable/Disable Time
Resume Time
RMS Period Jitter
RMS Phase Jitter (random)
Symbol
T_start
T_oe
T_resume
T_jitt
T_phj
Min.
–
–
–
–
–
–
Typ.
–
–
6
1.7
1.7
0.5
Max.
10
150
10
2
2
1
Unit
ms
ns
ms
ps
ps
ps
Condition
Measured from the time Vdd reaches its rated minimum value
f = 80 MHz. For other frequencies, T_oe = 100 ns + 3 cycles
Measured from the time ST pin crosses 50% threshold
f = 10 MHz, Vdd = 2.5V, 2.8V or 3.3V
f = 10 MHz, Vdd = 1.8V
f = 10 MHz, Integration bandwidth = 12 kHz to 20 MHz, All Vdds
Note:
1. All electrical specifications in the above table are measured with 15pF output load, Contact SiTime for higher drive options.
Pin Configuration
Pin
Symbol
V control
Output
Enable
1
VC/OE/ST/NC
Standby
NC
2
3
4
GND
CLK
VDD
Power
Output
Power
Voltage control
H or Open
[2]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
H or Open
[2]
: specified frequency output
L: output is low (weak pull down). Device goes to sleep mode. Supply
current reduces to I_std.
No connect (input receiver off)
Electrical and case ground
Oscillator output
Power supply voltage
GND
2
3
Functionality
Top View
VC/OE/ST
1
4
VDD
OUT
Note:
2. A pull-up resistor of <10 k between OE/ ST pin and Vdd is recommended in high noise environment when the device operates in OE/ST mode.
Absolute Maximum
Attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. Actual perfor-
mance of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Min.
-65
-0.5
–
–
Max.
150
4
2000
260
Unit
°C
V
V
°C
Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev. 1.0
Page 2 of 7
www.sitime.com
SiT5001
1-80 MHz MEMS TCXO and VCTCXO
The Smart Timing Choice
The Smart Timing Choice
Timing Diagram
90% Vdd, 2.5/2,8/3.3V devices
Vdd
95% Vdd, 1.8V devices
Vdd
Pin 4 Voltage
50% Vdd
T_resume
CLK Output
CLK Output
ST Voltage
T_start
T_start: Time to start from power-off
T_resume: Time to resume from ST
(ST/OE Mode)
(ST Mode Only)
Phase Noise Plot
Phase Noise, 10M Hz carrier, 3.3V, LVCM OS output, TCXO
-100
-110
-120
-130
-140
-150
-160
-170
3
10
Integrated random phase jitter (RM S, 12kHz-5M Hz): 0.52ps
Phase Noise (dBc/Hz)
10
4
10
Frequency O ffset (Hz)
5
10
6
Rev. 1.0
Page 3 of 7
www.sitime.com
SiT5001
1-80 MHz MEMS TCXO and VCTCXO
The Smart Timing Choice
The Smart Timing Choice
SoftEdge™ Option
The SoftEdge™ output is available as a standard option for the SiT500x family of MEMS (VC)TCXOs. It is typically used for EMI
reduction similar to that of the clipped sinewave output common to many quartz based TCXOs.
In the SoftEdge™ mode, the slower rise/fall edges of the output waveform reduce the higher clock harmonics in a digital clock
signal, minimizing EMI radiation at these harmonics. The table below show the actual rise/fall time in relation to the desired
output frequency and the supply voltage with a 10 k / 10pF load. Rail-to-rail swing of the output is maintained for these
supported frequencies.
Rise/Fall Time for SoftEdge™ Option
Parameter
Rise/Fall Time
Symbol
Tr, Tf
Min.
4.0
2.5
1.5
1.5
Typ.
6.5
4.0
3.5
2.5
Max.
9.5
6.0
5.0
4.5
Unit
ns
ns
ns
ns
Condition
1-26 MHz, 1.8V, 3.0 and 3.3V, MHz 10k and 10 pF, 20%-80% Vd
1-26 MHz, 2.5V and 2.8V, MHz 10k and 10 pF, 20%-80% Vdd
26-50 MHz, 1.8V, 3.0V and 3.3V, MHz 10k and 10 pF, 20%-80% Vdd
26-50 MHz, 2.5V and 2.8V, MHz 10k and 10 pF, 20%-80% Vdd
SoftEdge™ Waveform Examples and Corresponding Harmonics Reduction
Figures below illustrate the harmonic power reduction as the rise/fall times are slowed from the standard squarewave output to
that of the SoftEdge™ output. In general, the 1.8V device shows the lowest harmonics and provides best EMI performance
comparing to devices with higher operating voltages.
LVCMOS and SoftEdge™ Outputs,
VDD = 3.3V
SoftEdge
LVCMOS
3.5
20
Odd Harmonic Power Comparison for LVCMOS and SoftEdge™ Outputs,
VDD = 3.3V
SoftEdge
LVCMOS
3
10
Harmonic Power (dbm)
2.5
0
-10dBm
Amplitude (V)
2
-10
1.5
-20
1
-24.4dbm
-30
0.5
0
-40
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
0
2
4
6
8
10
12
14
16
18
20
Time (ns)
Harmonic Number
LVCMOS and SoftEdge Outputs,
VDD = 1.8V
SoftEdge
LVCMOS
20
Odd Harmonic Power Comparison for LVCMOS and SoftEdge Outputs,
VDD = 1.8V
SoftEdge
LVCMOS
10
Harmonic Power (dbm)
Amplitude ( 0.5V/Div )
0
-10
-17 dBm
-20
-22
dBm
-30
-40
Time ( 20ns/Div )
0
2
4
6
8
10
12
14
16
18
20
Harmonic Number
LVCMOS and SoftEdge Outputs,
VDD = 2.5V
SoftEdge
LVCMOS
20
Odd Harmonic Power Comparison for LVCMOS and SoftEdge Outputs,
VDD = 2.5V
SoftEdge
LVCMOS
10
Harmonic Power (dbm)
Amplitude( 0.5V/Div)
0
-11 dBm
-10
-20
-20 dBm
-30
-40
0
2
4
6
8
10
12
14
16
18
20
Time (20 ns/Div)
Harmonic Number
Rev. 1.0
Page 4 of 7
www.sitime.com
SiT5001
1-80 MHz MEMS TCXO and VCTCXO
The Smart Timing Choice
The Smart Timing Choice
Dimensions and Patterns
Package Size – Dimensions (Unit: mm)
[3]
2.7 x 2.4 x 0.75 mm (100% compatible with 2.5 x 2. 0 mm footprint)
Recommended Land Pattern (Unit: mm)
[4]
YXXXX
3.2 x 2.5 x 0.75 mm
2.2
#4
3.2 ± 0.05
#4
#3
#3
2.1
2.5 ± 0.05
0.9
0.7
YXXXX
#1
#2
1.9
#2
#1
0.75 ± 0.05
0.9
1.4
5.0 x 3.2 x 0.75 mm
2.54
5.0 ± 0.05
#4
#3
#3
2.39
#4
3.2 ± 0.05
0.8
1.1
YXXXX
#1
#2
2.2
0.75 ± 0.05
#2
#1
1.15
1.5
7.0 x 5.0 x 0.90 mm
7.0 ± 0.05
5.08
5.08
5.0 ± 0.05
2.6
YXXXX
1.1
3.81
0.90 ± 0.10
1.4
2.2
Notes:
3. Top marking: Y denotes manufacturing origin and XXXX denotes manufacturing lot number. The value of “Y” will depend on the assembly location of the device.
Why can't TACCR0 be assigned a variable? For example: TACTL = TBSSEL_2 + TBCLR; TACCTL0 = CCIE; TACCR0=X; TACTL|=MC_1; where X is an unsigned int type variable, and the compiler used is IAR5.3?...
CD4046 is selected as the frequency multiplier, and the input frequency 50HZ is multiplied by 256 times to control AD sampling, but the output frequency keeps jumping. And later when debugging, I dire...
If 12864 uses parallel driver, many I/O ports will be occupied. If serial driver is used, many I/O ports can be saved. Can anyone write a serial driver for 12864? Can you upload it? Thank you!...
If I keep creating a new memory space and then delete it in the program, will it cause a memory leak after N consecutive times? I have seen that the address generated by each new NEW is increasing. If...
I want to DIY a USB flash drive. Can you please help me? Can you tell me the choice of the main controller, the pin functions of the main controller and flash memory, and the peripheral circuits? I wi...
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
Introduction
As the country increases its efforts to control the atmospheric environment, motorcycle emission regulations will become stricter year by year, and motorcycles that do not meet the...[Details]
0 Introduction
Ultrasonic waves
are mechanical waves with a frequency of more than 20KHz, and the propagation speed in the air is about 340 m/s (at 20°C). Ultrasonic waves can be gene...[Details]
Almost everyone in a student dormitory has a bedside lamp. But if you want to read for a while after turning off the lights and don't want to disturb your roommates' sleep, you may need a reading l...[Details]
The fluorescent lamps and energy-saving lamps we commonly use now have greatly improved luminous efficiency compared with the earlier ordinary incandescent lamps and have been widely used. With the...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems (GP...[Details]
Power supply is often the most easily overlooked link in the circuit design process. In fact, as an excellent design, power supply design should be very important, which greatly affects the perfor...[Details]
1 Introduction
At present, people have higher and higher requirements for the quality of life. When people are busy with work, soymilk machine is a new type of household beverage machine. It uses so...[Details]
DigRF
is
poised to replace the two main forms of data communication paths between RF and baseband semiconductor devices:
analog
signaling, and proprietary digital signaling (paralle...[Details]
introduction
The air compressor unit in the operating area of a lead-zinc mine in Guangdong is a key equipment in mining production. There are six imported Ingersoll Rand CENTAC air compress...[Details]
For a long time, hackers have not had the opportunity to enter the control network of the car. But since the advent of Bluetooth technology and the use of wireless LAN bus systems, this situation w...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
