Y08560R20000G0R datasheet, PDF

Datasheet> All Categories > Passive components> Y08560R20000G0R

Y08560R20000G0R: DescriptionRES 0.2 OHM 2% 1W 2516 WIDE; CategoryPassive components; File Size1MB，5 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

Y08560R20000G0R Overview

RES 0.2 OHM 2% 1W 2516 WIDE

Y08560R20000G0R Parametric

Parameter Name	Attribute value
resistance	200 mOhms
Tolerance	±2%
Power (W)	1W
component	metal foil
characteristic	Current sensing, moisture proof, non-inductive
Temperature Coefficient	±2ppm/°C
Operating temperature	-55°C ~ 150°C
Package/casing	Width 2516 (6440 metric), 1625
Supplier device packaging	SMD
size/dimensions	0.160" long x 0.250" wide (4.06mm x 6.35mm)
Height - Installation (maximum)	0.040"（1.02mm）
Number of terminals	4
failure rate	-

Preview

Download Datasheet

View All

VCS1625P

Vishay Foil Resistors

High Precision Surface Mount Current Sensing Chip Resistor with Power

Rating to 1 W, Temperature Coefficient of Resistance of

± 2 ppm/°C and Load Life Stability of ±0.015%

FEATURES

NEW

INTRODUCTION

Model VCS1625P is a surface mount resistor designed with

4 pads for Kelvin connection. Utilizing VFR’s (Vishay Foil

Resistors’) Bulk Metal® Foil as the resistance element, it

provides performance capabilities far greater than other

resistor technologies can supply in a product of comparable

size.

The key performance of the new VCS1625P is its high rated

power up to 1W. This small device dissipates heat almost

entirely through the pads so surface mount users are

encouraged to be generous with the board’s pads and

traces. Gold terminations are available on special order.

The four terminal device separates the current leads from the

voltage sensing leads. This configuration eliminates the

effect of the lead wire resistance from points A to B and

C to D, allowing low TCR current sensing.

VFR’s application engineering department is available to

advise and to make recommendations. For non-standard

technical requirements and special applications, please

contact

foil@vishaypg.com.



Temperature coefficient of resistance (TCR):



± 2 ppm/°C typical (- 55 °C to + 125 °C,

+ 25 °C ref.) (see table 1)



Resistance range: 0.01



to 10

(for

higher

or lower values, please contact Application

Engineering)



Vishay Foil resistors are not restricted to standard values,

we can supply specific “as required” values at no extra cost

or delivery (e.g. 1.234



vs. 1

)



Resistance tolerance: to ± 0.2% (0.05% is also available)



Load life stability: 0.015 % at 70 °C, 2000 h at rated power



Thermal EMF: 0.05 µV/°C typical



Electrostatic discharge (ESD) at least to 25 kV



Short time overload < 0.005 %



Thermal stabilization time < 1 s (nominal value achieved

within 10 ppm of steady state value)



Power rating: to 1 W at + 70 °C (Figure 1)



Non inductive: non capacitive design



Rise time: 1 ns effectively no ringing



Current rating: 5 A maximum



Current noise: 0.010 µV

RMS

/V of applied voltage



(< - 40 dB)



Voltage coefficient: < 0.1 ppm/V



Non inductive: < 0.08 µH



Non hot spot design



Prototype quantities available in just 5 working days or

sooner



For better performances, please review the VCS1625ZP

(Z-Foil) datasheet

TERMINATIONS



Two lead (Pb)-free options are available:

gold plated or tin plated



Tin/lead plated

FIGURE 1 - POWER DERATING CURVE

Percent of Rated Power

- 55 °C

100

- 75

∞

+ 70 °C

- 50

- 25

+ 25

+ 50

+ 75 + 100 + 125 + 150 + 175

Ambient Temperature (°C)

* Pb containing materials are not RoHS compliant, exemptions may apply

Document Number: 63216

Revision: 28-Aug-12

For any questions, contact:

foil@vishaypg.com

www.vishayfoilresistors.com

Legal Disclaimer Notice

Vishay Precision Group, Inc.

Disclaimer

ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf

(collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in

any other disclosure relating to any product.

The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but

not limited to, the warranty expressed therein.

VPG makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase.

To the maximum extent permitted by applicable law, VPG disclaims (i) any and all liability arising out of the

application or use of any product, (ii) any and all liability, including without limitation special, consequential or

incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose,

non-infringement and merchantability.

Information provided in datasheets and/or specifications may vary from actual results in different applications and

performance may vary over time. Statements regarding the suitability of products for certain types of applications

are based on VPG’s knowledge of typical requirements that are often placed on VPG products. It is the customer’s

responsibility to validate that a particular product with the properties described in the product specification is suitable for

use in a particular application. You should ensure you have the current version of the relevant information by contacting

VPG prior to performing installation or use of the product, such as on our website at vpgsensors.com.

No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any

conduct of VPG.

The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise

expressly indicated. Customers using or selling VPG products not expressly indicated for use in such applications do

so entirely at their own risk and agree to fully indemnify VPG for any damages arising or resulting from such use or sale.

Please contact authorized VPG personnel to obtain written terms and conditions regarding products designed for such

applications.

Product names and markings noted herein may be trademarks of their respective owners.

Document No.: 63999

Revision: 15-Jul-2014

www.vpgsensors.com

Recommended Resources

Zero-crossing trigger circuit design based on thyristor

Temperature switch circuit three

Wind battery charger

AD7711 LC²MOS signal conditioning ADC circuit with RTD current source

Switching power supply circuit diagram composed of STR-S5941

Average absolute value comparison circuit diagram with temperature compensation

Help!!! I need help desperately!!!: :loveliness:I just made a signal generator!! Now the teacher asked me to make a lower computer that can display the waveform on the computer. I don’t know how to do it. I hope you guys can help me giv...; daichenyu1987 DIY/Open Source Hardware

ucos event flag group problem: A question about the ucos event flag group: Can I call OSFlagPend on the same event flag group variable in multiple different tasks? And then call OSFlagPost in one task to satisfy all the waiting tas...; 562327931 Real-time operating system RTOS

Creative Organ Monitor: This organ monitor allows medical staff to check the patient's condition remotely without having to go to the ward in person. It can detect the patient's pulse rate, body temperature, and blood pressu...; xyh_521 Creative Market

I want to go to Zhongembed for training, but I wonder if it’s a good idea?: I have graduated and want to work on embedded LINUX. I am in Chongqing. It seems that there are only Zhongqian and some mobile academy for embedded training. I don't know if Zhongqian is good. I went ...; heyi000 Embedded System

[RVB2601 Creative Application Development] PC Health Status Detector: PC Health CheckerAuthor: Song GuangfaProject BackgroundWhen using the PC, the fan often runs wildly. When you open the task manager and check the CPU usage, the CPU soars to 100% due to the task manag...; sgf201 XuanTie RISC-V Activity Zone

I would like to ask you, how can we distinguish between a USB flash drive and a mobile hard drive?: The question is roughly as the title says. Is it possible to distinguish between a USB flash drive and a mobile hard drive based on which flags or structures? Thanks for your advice!...; gl417270208 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components