that is designed for low power, wireless applications. It features
a 12-bit analog-to-digital converter (ADC), a low power ARM®
Cortex®-M3 processor, a 862 MHz to 928 MHz and 431 MHz
to 464 MHz RF transceiver, and Flash®/EE memory. The
ADuCRF101
is packaged in a 9 mm × 9 mm LFCSP.
The data acquisition section consists of a 12-bit SAR ADC.
The six inputs can be configured in single-ended or differential
mode. When configured in single-ended mode, they can be
used for ratiometric measurements on sensors that are powered,
when required, from the internal low dropout regulator (LDO).
An internal battery monitor channel and an on-chip tempera-
ture sensor are also available.
This wireless data acquisition system is designed to operate in
battery-powered applications where low power is critical. The
device can be configured in normal operating mode or different
low power modes under direct program control. In flexi mode,
any peripheral can wake up the device and operate it. In hibernate
mode, the internal wake-up timer remains active. In shutdown
mode, only an external interrupt can wake up the device.
The
ADuCRF101
integrates a low power ARM Cortex-M3
processor. It is a 32-bit RISC machine, offering up to 1.25 DMIPS
peak performance. The ARM Cortex-M3 processor also has a
flexible 14-channel direct memory access (DMA) controller that
supports communication peripherals, serial peripheral interface
(SPI), UART, and I
2
C. Also provided on chip are 128 kB of
nonvolatile Flash/EE memory and 16 kB of SRAM.
ADuCRF101
A 16 MHz on-chip oscillator generates the system clock. This
clock can be internally divided for the processor to operate at
a lower frequency, thus saving power. A low power, internal
32 kHz oscillator is available and can be used to clock the four
timers, as follows: two general-purpose timers, a wake-up timer,
and a system watchdog timer.
A range of communication peripherals can be configured, as
required, in a specific application. These peripherals include
UART, I
2
C, SPI, GPIO ports, PWM, and RF transceivers.
The RF transceiver communicates in the 862 MHz to 928 MHz
and 431 MHz to 464 MHz frequency bands using multiple
configurations.
On-chip factory firmware supports in-circuit serial download
via the UART, and nonintrusive emulation and program download
are also supported via the serial wire interface. These features
are incorporated into a low cost development system supporting
this precision analog microcontroller family.
The
ADuCRF101
operates from 2.2 V to 3.6 V and is specified
over an industrial temperature range of −40°C to +85°C. It is
available in a 64-lead LFCSP package.
Rev. A | Page 3 of 19
ADuCRF101
SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Data Sheet
AVDD = IOVDD = VDDBAT1 = VDDBAT2 = 2.2 V to 3.6 V, V
REF
= 1.25 V internal reference, f
CORE
= 16 MHz, T
A
= −40°C to +85°C,
unless otherwise noted. Default ADC sampling frequency of 167 kSPS (eight acquisition clocks and ADC clock frequency of 4 MHz).
Table 1.
Parameter
DC ACCURACY
Resolution
Integral Nonlinearity
Test Conditions/Comments
Single-ended input mode; applies to all ADC
input channels
V
REF
= 1.25 V from internal reference
V
REF
= 1.8 V from LDO
Differential Nonlinearity
DC Code Distribution
Differential
Ratiometric Measurement
CALIBRATED ENDPOINT ERRORS
Offset Error
Gain Error
DYNAMIC PERFORMANCE
Signal-to-Noise Ratio (SNR)
Signal-to-Noise + Distortion Ratio
(SINAD)
Total Harmonic Distortion (THD)
Spurious-Free Dynamic Range
(SFDR)
ANALOG INPUT
Input Voltage Ranges
2
Single-Ended Input
Differential Input
Leakage Current
Input Capacitance
ON-CHIP VOLTAGE REFERENCE
Output Voltage
Accuracy
Reference Temperature Coefficient
Power Supply Rejection Ratio
(PSRR)
Output Impedance
Internal V
REF
Power-On Time
TEMPERATURE SENSOR
2
Voltage Output at 25°C
Voltage Temperature Coefficient
Thermal Impedance
CURRENT CONSUMPTION
Cortex-M3 in Shutdown Mode
Cortex-M3 in Hibernate Mode
RF Transceiver in Sleep Mode
Memory Retained
Memory Not Retained
Rev. A | Page 4 of 19
Min
Typ
Max
Unit
Guaranteed no missing code at 167 kSPS
ADC input shorted, V
CM
= 0.4 V
Using two 10 kΩ resistors
Measured using the factory-set default values of
the ADCOF and ADCGN registers
1
12
−2.5 to
+1
−2.5 to
+0.5
±1
1
5
Bits
LSB
LSB
LSB
LSB
LSB
±1.6
±1
f
IN
= 1 kHz sine wave
68
66
−69
70
LSB
LSB
dB
dB
dB
dB
0
0
Excluding VREF pin
During ADC acquisition
100
20
1.25
±5
±40
60
2
5
435
1.14
35
RF transceiver in sleep mode, memory not retained
Wake-up timer running from external 32 kHz
crystal, 8 kB of SRAM retained (8 kB not retained)
280
V
REF
V
CM
± V
REF
/2
V
V
nA
pF
V
mV
ppm/°C
dB
Ω
ms
mV
mV/°C
°C/W
nA
Measured at T
A
= 25°C
0.47 µF external capacitor
Indicates die temperature
1.9
1.75
µA
µA
Data Sheet
Parameter
RF Transceiver in Receive Mode
RF Transceiver in Transmit Mode
Cortex-M3 in Active Mode
Static Current
Dynamic Current
START-UP TIME
2
From Flexi Mode
From Hibernate Mode
From Power-On and Shutdown
Mode
RF Link, Waking Up from Sleep
Mode
POWER SUPPLY REQUIREMENTS
Power Supply Voltage Range
2
POWER SUPPLY MONITOR
Trip Point Voltage
WATCHDOG TIMER
2
Timeout Period
FLASH/EE MEMORY
2
Endurance
3
Data Retention
4
DIGITAL INPUTS
Input Current (Leakage Current)
Input Capacitance
LOGIC INPUTS
Input Low Voltage, V
INL
Input High Voltage, V
INH
LOGIC OUTPUTS
Output High Voltage, V
OH
Output Low Voltage, V
OL
32.768 kHz CRYSTAL
Input Current (Leakage Current)
LFXTAL1 Input Capacitance
LFXTAL2 Output Capacitance
26 MHz CRYSTAL
XOSC26P Input Capacitance
XOSC26N Output Capacitance
INTERNAL HIGH FREQUENCY (HF)
OSCILLATOR
Tolerance
INTERNAL LOW FREQUENCY (LF)
OSCILLATOR
Tolerance
MCU CLOCK DIVIDER
2
EXTERNAL CLOCK INPUT
2
Range
1
2
ADuCRF101
Test Conditions/Comments
Min
Typ
12.8
9 to 32
Max
Unit
mA
mA
RF transceiver idle (PHY_ON state or PHY_OFF
state)
1
2.0
210
FCLK is the Cortex-M3 clock or divided version of
the 16 MHz oscillator
From wake-up event to user code execution
From applying power/asserting active external
interrupt to user code execution
Includes 310 µs for 26 MHz crystal startup
(7 pF load capacitor at T
A
= 25°C)
2.2
2
Programmable
0
10,000
10
10
10
512
3 to 5
13.4
55
562.8
mA
µA/MHz
FCLK
µs
ms
µs
3.6
V
V
sec
Cycles
Years
nA
pF
T
J
= 85°C
All digital inputs, excluding LFXTAL1 and XOSC26P
V
INH
= IOVDD or V
INH
= 2.2 V, pull-up disabled;
V
INL
= 0 V, pull-up disabled
Excluding P2.4
All logic inputs, including LFXTAL1 but excluding
XOSC26P
0.2 × IOVDD
0.7 × IOVDD
I
SOURCE
= 1 mA
I
SINK
= 1 mA
32.768 kHz crystal, for use with timers
V
INH
= IOVDD or V
INH
= 2.2 V, V
INL
= 0 V
IOVDD − 0.4
0.36
50
5
5
10
10
16
±3
32.768
±20
Eight programmable core clock dividers
External MCU clock range allowed
1
32.768
128
16,000
V
V
V
V
nA
pF
pF
pF
pF
MHz
%
kHz
%
Processor clock by default
kHz
For detailed information, see the
UG-231 User Guide.
These values are not production tested; they are guaranteed by design and/or characterization data at production release.
3
Endurance is qualified to 10,000 cycles as per JEDEC Standard No. 22-A117 and measured at −40°C, +25°C, and +85°C. Typical endurance at 25°C is 170,000 cycles.
4
Retention lifetime equivalent at a junction temperature (T
J
) of 85°C as per JEDEC Standard No. 22-A117. Retention lifetime derates with junction temperature.
[b] This is the video courseware of the "Texas Instruments Adapter Power Supply Chip Online Seminar" held by TI engineers on October 18. If you like it, take it. [/b] Texas Instruments (TI) has announ...
Dear moderator, where can I find information that introduces the working principles and characteristics of various types of attenuators and phase shifters?...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
Images in science fiction movies often break through the limits of reality, such as in the movie "Minority Report." Tom Cruise uses a multi-touch screen to browse information. Capacitive sensing te...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
Xiaomi, a well-known Internet phone in mainland China, won a million-unit order contract from China Unicom on November 20 last year, which made Xiaomi famous in mainland China. In April this year...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
I've been studying dot matrix recently. It looks simple, but it takes a while to master it completely! The 8*8 dot matrix hardware circuit I'm making now is like this. The row is driven by 74HC138 + t...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
