PSB50/40/30
Series
PSB50
PSB40
PSB30
50 W
40 W
30
W
50, 40 & 30 W Programmable Constant Current LED Driver
with Tri-Mode Dimming™ (TRIAC, ELV & 0-10 V)
Nominal Input
Voltage
120 to 277 Vac,
220 to 240 Vac
Max.
Output
Power
50 W
Efficiency
Max. Case
Temperature
THD
Power Factor
Dimming Method
Forward-Phase,
Reverse-Phase
& 0 - 10V
Dimming
Range
Startup
Time
300 ms
typical
up to 90% 90°C (measured
(from 100% to 50% (from 100% to 50%
typical
at the hot spot)
< 20%
> 0.9
of max rated power of max rated power)
TRIAC/ELV
Dimmer
+ Dim
- Dim
0-10 V
Dimmer
PSB50
+ LEDs
Series
- LEDs
In
fo
rm
Aluminum Case
L 98.5 * W 26.2 * H 21.85 mm
(L 3.88 * W 1.03 * H 0.86 in.)
FEATURES
PROGRAMMING
Pr
e
•
Serial port programming
•
Current: 100% to 50% in each voltage range
•
Data log read: SKU, S/N, lot code, hours of operation,
FW rev., fault events: power failure, transients (short or
surge), thermal
•
Fully programmable and selectable 0-10V dimming
profiles: Non-linear with dim-to-off, Logarithmic, Non-
Linear without dim-to-off.
lim
•
Non-linear 0-10V dimming profile with dim-to-off pre-loaded by
default (10V to 9.1V=100%, 1.5V to 0.55V=1%, <0.55V=dim-to-off)
•
UL Class P
•
Class 2 power supply
•
Lifetime: 50,000 hours @ Tc = 75°C
•
90°C maximum case hot spot temperature
•
IP20-rated case with silicone-based potting
•
Surge protection:
•
IEC61000-4-5: 2 kV line to line/2 kV line to earth
•
2.5 kV ring wave: ANSI/IEEE c62.41.1-2002 & c62.41.2-2002
category A
•
Complies with ENERGY STAR®, DLC (DesignLight Consortium®)
and CA Title 24 technical requirements
ina
ry
Neutral:
•
White: 120 Vac
•
Blue: 230 Vac
Line:
•
Black: 120 Vac
•
Brown: 230 Vac
OTHER MOUNTING OPTIONS
Bottom Leads with Studs
Add “-X” suffix to part
number.
APPLICATIONS
•
Commercial & residential lighting
•
Architectural lighting
•
Indoor Lighting
© ERP Power, LLC
1
PSB50/40/30 Series Data Sheet – Preliminary Information
Rev. March 2018
at
ion
1 - 100%
(% of Iout)
Aluminum Case
L 158 * W 26.25 * H 21.85 mm
(L 6.22 * W 1.03 * H 0.86 in.)
Purple: + Dim
PSB50
Series
Grey: - Dim
Red: + LEDs
Blue: - LEDs
Wiring Diagram
5
CA Title 24
PSB50/40/30
Series
PSB50
PSB40
PSB30
50 W
40 W
30
W
50, 40 & 30 W Programmable Constant Current LED Driver
with Tri-Mode Dimming™ (TRIAC, ELV & 0-10 V)
1 - ORDERING INFORMATION
Part Number
Nominal
Input
Voltage
(Vac)
Max
Output
Power
(W)
Iout
(mA)
Vout Vout Vout
Min. Nom. Max.
(Vdc) (Vdc) (Vdc)
Open
Loop
(No Load)
Voltage
(Vdc)
50
35
44.2
35
120 TO 277 VAC NOMINAL INPUT VOLTAGE
PSB30W
PSB30W-0700-42
PSB30W-1050-27
PSB30W-0800-34
PSB40W-1400-27
PSB50W-0550-85
PSB50W-0850-56
PSB50W-1200-42
PSB50W-1400-34
120 to 277
120 to 277
120 to 277
120 to 277
120 to 277
120 to 277
120 to 277
120 to 277
29.4
28.4
27.2
37.8
46.8
47.6
50.4
47.6
350 to 700
525 to 1050
400 to 800
700 to 1400
275 to 550
425 to 850
600 to 1200
700 to 1400
28
18
23
18
37.8
24.3
30.6
24.3
42
27
34
27
In
fo
rm
Side Leads
Side Leads
Side Leads
Side Leads
57
38
28
23
76.5
50.4
37.8
30.6
85
56
42
34
100
60
50
44.2
Side Leads
Side Leads
Side Leads
Side Leads
28
18
23
18
57
38
28
23
37.8
24.3
30.6
24.3
76.5
50.4
37.8
30.6
42
27
34
27
85
56
42
34
50
35
44.2
35
100
60
50
44.2
PSB40W
PSB50W
220 to 240 VAC NOMINAL INPUT VOLTAGE
PSB30W
PSB40W-1400-27-T 220 to 240
PSB50W-0550-85-T
PSB50W-0850-56-T
PSB50W-1200-42-T
PSB50W-1400-34-T
220 to 240
220 to 240
220 to 240
220 to 240
ina
ry
PSB40W
PSB50W
37.8
46.8
47.6
50.4
47.6
700 to 1400
275 to 550
425 to 850
600 to 1200
700 to 1400
PSB30W-0700-42-T 220 to 240
PSB30W-1050-27-T 220 to 240
PSB30W-0800-34-T 220 to 240
29.4
28.4
27.2
350 to 700
525 to 1050
400 to 800
Pr
e
SaveEnergy@erp-power.com
lim
Notes:
•
For each model, the default output current setting is the maximum current.
•
For additional options of output current and output voltage, contact your sales representative or send an
email to:
SaveEnergy@erp-power.com
•
Please order the programming cable using the part number: “PROG-JACK-USB”.
2
at
ion
Comments
2Q2018 release
3Q2018 release
3Q2018 release
3Q2018 release
2Q2018 release
3Q2018 release
Terminal Blocks
Terminal Blocks
Terminal Blocks
Terminal Blocks
Terminal Blocks
Terminal Blocks
Terminal Blocks
Terminal Blocks
3Q2018 release
www.erp-power.com
PSB50/40/30
Series
PSB50
PSB40
PSB30
50 W
40 W
30
W
50, 40 & 30 W Programmable Constant Current LED Driver
with Tri-Mode Dimming™ (TRIAC, ELV & 0-10 V)
2 - INPUT SPECIFICATION
(@25°C ambient temperature)
Units Minimum
Input Voltage Range (Vin)
- Models with flying leads
- Models with "-T" suffix
Input Frequency Range
- Models with flying leads
- Models with "-T" suffix
Input Current (Iin)
Power Factor (PF)
Inrush Current
A
Vac
90
198
47
47
Typical
120, 277
230
60
50
Maximum
305
264
63
53
0.5 A @ 120 Vac
0.28 A @ 230 Vac
0.23 A @ 277 Vac
Notes
The rated output current for each model is achieved at Vin≥108 Vac & at
Vin≥198 Vac for models with flying leads, and at Vin≥209 Vac for models
with "-T" suffix.
At nominal load
Hz
A
0.9
> 0.9
Meets NEMA-410 requirements
Leakage Current
Input Harmonics
Total Harmonics
Distortion (THD)
Efficiency
Isolation
mA
Complies with IEC61000-3-2 for Class C equipment
20%
-
%
-
up to 90%
The AC input to the main DC output is isolated and meets Class II reinforced/double insulation power supply
3 - MAIN OUTPUT SPECIFICATION
(@25°C ambient temperature)
Output Voltage (Vout)
Output Current (Iout)
Output Current Regulation
Output Current Overshoot
Ripple Current
Units Minimum Typical Maximum
Vdc
See ordering information for details
mA
%
Notes
Dimming Range (% of Iout)
lim
%
1
ms
Pr
e
Start-up Time
Isolation
The main DC output is certified and tested per UL8750 Class 2 or LED Class 2
SaveEnergy@erp-power.com
ina
ry
-5
-
±2.5
-
5
%
10
≤
10% of rated output current for
each model
100
300
500
In
fo
rm
0.3 mA @ 120 Vac
0.6 mA @ 230 Vac Measured per IEC60950-1
0.7 mA @ 277 Vac
At nominal input voltage and with nominal LED voltage
From 100% to 50% of rated power
At any point on the sine wave and 25°C
Active limiting inrush current is available as an option. Please contact
your ERP representative or send an email to SaveEnergy@erp-power.com.
At nominal input voltage and nominal LED voltage
From 100% to 50% of rated power
Complies with DLC (Design Light Consortium) technical requirements
Measured with nominal input voltage, a full sinusoidal wave form and
without dimmer attached.
See ordering information for details
The rated output current for each model is achieved at Vin≥108 Vac & at Vin≥198 Vac.
At nominal AC line voltage
Includes load and current set point variations
The driver does not operate outside of the regulation requirements for more than 500
ms during power on with nominal LED load and without dimmer.
Measured at nominal LED voltage and nominal input voltage without dimming
Calculated in accordance with the IES Lighting Handbook, 9th edition
The dimming range is dependent on each specific dimmer. It may not be able to
achieve 1% dimming with some dimmers.
Dimming performance is optimal when the driver is operated at its nominal output
voltage matching the LED nominal Vf (forward voltage). Dimming performance may
vary when the driver is operated near its minimum output voltage.
Without any dimmer attached, and at nominal input voltages and nominal load
Measured from application of AC line voltage to 100% light output
Complies with ENERGY STAR® luminaire specification and CA Title 24
3
at
ion
www.erp-power.com
PSB50/40/30
Series
PSB50
PSB40
PSB30
50 W
40 W
30
W
50, 40 & 30 W Programmable Constant Current LED Driver
with Tri-Mode Dimming™ (TRIAC, ELV & 0-10 V)
4 - 0-10 V DIMMING CONTROL
(@25°C ambient temperature)
In the PSB50/40/30 series, several 0-10V dimming profiles can be selected, such as a logarithmic profile, a non-linear
profile with 1% minimum dimming and dim-to-off, and a non-linear profile with 10% minimum dimming and no dim-to-off.
Furthermore, every point in the non-linear dimming profile can be programmed using the programming software.
By default, the non-linear profile with 1% minimum dimming and dim-to-off (show in
figure
1) is pre-loaded in the
PSB50/40/30 series.
Units Minimum Typical Maximum
+Dim Signal, -Dim Signal
The PSB50/40/30 series operate only with 0-10V dimmers that sink current. The method to dim the output current of the
driver is done via the +Dim/-Dim Signal pins. The +Dim/-Dim signal pins can be used to adjust the output setting via a
standard commercial wall dimmer, an external control voltage source (0 to 10 Vdc), or a variable resistor when using the
recommended number of LEDs. The dimming input permits 1% to 100% dimming.
100% of output current between 10 V and 9.1 V,
Linear between 9.1 V and 1.5 V,
1% of output current between 1.5 V and 0.55 V,
Output current off below 0.55 V.
%
V
V
V
V
1
9.1
1.5
0.55
100
Dimming Profile
(see figure 1)
Dimming Range
High Level Voltage - A
Low Level Voltage - B
Dim to Off - C
Dim to Off Hysteresis - D
Current Supplied by the
+Dim Signal Pin
Output Current Tolerance
While Being Dimmed
Isolation
mA
%
The 0-10 V circuit is isolated from the AC input and meets Class II reinforced/double insulation power supply.
Pr
e
Percent of Output Current
(Normalized to Rated Current)
lim
ina
ry
0.5
+0.1
0.6
+0.2
1
±8
100%
1%
(V)
C
D
B
Dimming Voltage (V)
0%
In
fo
rm
Notes
As a percent of the output current
The tolerance of the output current while being dimmed is
≤
+/-8% until down to 1.5V.
Figure 1
4
www.erp-power.com
SaveEnergy@erp-power.com
at
ion
A
10
PSB50/40/30
Series
PSB50
PSB40
PSB30
50 W
40 W
30
W
50, 40 & 30 W Programmable Constant Current LED Driver
with Tri-Mode Dimming™ (TRIAC, ELV & 0-10 V)
5 - ENVIRONMENTAL CONDITIONS
Units
Operating Ambient Temperature
(Ta)
Maximum Case Temperature (Tc)
Storage Temperature
Humidity
Cooling
Acoustic Noise
Mechanical Shock Protection
Vibration Protection
MTBF
Lifetime
°C
°C
°C
%
Minimum
-20
Typical
Maximum
50
+90
Notes
-40
5
-
Convection cooled
dBA
24
Measured at a distance of 1 meter, without dimmer
per EN60068-2-27
per EN60068-2-6 & EN60068-2-64
> 200,000 hours when operated at nominal input and output conditions, and at Tc
≤
75°C
50,000 hours at Tc
≤
75°C maximum case hot spot temperature (see hot spot tc on label in page 11)
6 - EMC COMPLIANCE AND SAFETY APPROVALS
cUL
cUL
CE
CB
ENEC
Pr
e
lim
Units
Vdc
EMC Compliance
Models with no suffix and with "-X" suffix: Compliant with FCC CFR Title 47 Part 15 Class B at 120 Vac & Class A at 277 Vac
Conducted and
Models with "-T" suffix: Compliant with EN55015 (CISPR 15) at 220, 230, and 240 Vac
Radiated EMI
IEC61000-3-2
For Class C equipment
Harmonic Current Emissions
IEC61000-3-3
Voltage Fluctuations & Flicker
ESD (Electrostatic
IEC61000-4-2
6 kV contact discharge, 8 kV air discharge, level 3
Discharge)
RF Electromagnetic Field
IEC61000-4-3
3 V/m, 80 - 1000 MHz, 80% modulated at a distance of 3 meters
Susceptibility
IEC61000-4-4
± 2 kV on AC power port for 1 minute, ±1 kV on signal/control lines
Electrical Fast Transient
± 2 kV line to line (differential mode) /± 2 kV line to common mode ground
Immunity
(tested to secondary ground) on AC power port, ±0.5 kV for outdoor cables
IEC61000-4-5
Compliance
Higher surge is available. Please contact your ERP representative or send an
Surge
email to SaveEnergy@erp-power.com.
ANSI/IEEE c62.41.1-2002 & c62.41.2-2002 category A, 2.5 kV ring wave
Conducted RF
IEC61000-4-6
3V, 0.15-80 MHz, 80% modulated
Disturbances
IEC61000-4-11 >95% dip, 0.5 period; 30% dip, 25 periods; 95% reduction, 250 periods
Voltage Dips
Safety Agency Approvals
UL8750 listed Class 2 (except PSB50W-0550-85)
CAN/CSA C22.2 No. 250.13-14 LED equipment for lighting applications
IEC61347-2-13 electronic control gear for LED Modules & EN55015 (EMC compliance)
ina
ry
Minimum
2500
Safety
Typical
Hi Pot (High Potential) or
Dielectric voltage-withstand
SaveEnergy@erp-power.com
In
fo
rm
+85
95
Non-condensing
50°C is the non-derated temperature (Refer to section 8
"Output power de-rating at higher temperatures".
Case temperature measured at the hot spot tc (see label
in page 11)
Maximum
Notes
Insulation between the input (AC line and Neutral)
and the output
Tested at the RMS voltage equivalent of 1767 Vac
5
at
ion
www.erp-power.com
京公网安备 11010802033920号
EEWORLD
