CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
NPCAP
TM
Surface Mount
-
・Super
low ESR, high ripple current capability
・Rated
voltage range : 16 to 25V
dc
, Capacitance range : 10 to 1,000μF
・Case
size :
φ5×4.5L
toφ10×12.2L
・Solvent
resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS2
Compliant
・Halogen
Free
PXG
Series
PXG
Downsized
PXE
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +105℃
16 to 25V
dc
±20%
(M)
Rated voltage×1.15
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
Characteristics
Bias Humidity
Surge Voltage
Failure Rate
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 15,000 hours
(E46,F45 : 3,000 hours) at 105℃.
Appearance
No significant damage
Capacitance change
≦±20%
of the initial value
D.F. (tanδ)
≦150%
of the initial specified value
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours (E46,F45 : 500 hours).
Appearance
No significant damage
Capacitance change
≦±20%
of the initial value
D.F. (tanδ)
≦150%
of the initial specified value
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ)and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20%
of the initial value
D.F. (tanδ)
≦150%
of the initial specified value
ESR
≦150%
of the initial specified value
Leakage current
≦The
initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS
[mm]
●
Terminal
◆MARKING
Size Code
E46
E61
F45
F61
F80
H70
H80
HA0
J80
JA0
JC0
L
A
B
C
φ
D
5
4.5 5.3 5.3 5.9
5
5.8 5.3 5.3 5.9
6.3 4.4 6.6 6.6 7.2
6.3 5.8 6.6 6.6 7.2
6.3 7.7 6.6 6.6 7.2
8
6.7 8.3 8.3 9.0
8
7.7 8.3 8.3 9.0
8 10.0 8.3 8.3 9.0
10 7.7 10.3 10.3 11.0
10 10.0 10.3 10.3 11.0
10 12.2 10.3 10.3 11.0
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.4
1.4
1.9
1.9
1.9
3.1
3.1
3.1
4.5
4.5
4.5
EX) 25V47µF
Code : A
0.2
B
±
W
P
C
±
0.2
φD±
0.5
G
14A
47
25
V
0.3max.
L
±
(Note)
0.3
A
±
0.2
Note : L+0.1/-0.2 for E46 and F45
L
±
0.5 for HA0, JA0 and JC0
◆PART
NUMBERING SYSTEM
A PXG
1
2
3
4
5
6
7
A RA
8
9
10
11
12
13
M
14
15
16
17
G
18
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 47µF:470, 100µF:101)
Taping code
Terminal code
Voltage code (ex. 16V:160, 20V:200)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001S
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
