Operating Temperature Range ........................... -40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range ............................ -65°C to +150°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only; functional operation of the device at these or any
other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device
reliability.
Package Information
PACKAGE TYPE: 16 WLP
Package Code
Outline Number
Land Pattern Number
THERMAL RESISTANCE, FOUR-LAYER BOARD
Junction to Ambient (θ
JA
)
58°C/W
W161F1+1
21-0491
Refer to
Application Note 1891
For the latest package outline information and land patterns (footprints), go to
www.maximintegrated.com/packages.
Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board.
For detailed information on package thermal considerations, refer to
www.maximintegrated.com/thermal-tutorial.
www.maximintegrated.com
Maxim Integrated
│
2
MAX20310
Ultra-Low Quiescent Current PMIC with
SIMO Buck-Boost for Wearable Applications
Electrical Characteristics
(V
BAT
= +1.2V, V
BB1OUT
= +1.8V, V
BB2OUT
= +1.2V, V
L1OUT
= +1.5V, V
L2OUT
= +1.0V, I
BB1OUT
= I
BB2OUT
= I
L1OUT
= I
L2OUT
= 0A,
T
A
= -40°C to +85°C, all registers in their default state, unless otherwise noted. Typical values are at T
A
= +25°C) (Note 1) (Note 2)
PARAMETER
SUPPLY CURRENT
Seal Input Current
KIN
Pullup Resistor to
GND
SYMBOL
I
SEAL
KIN
PULLUP
Buck-boost 1 enabled
CAP Quiescent Current
I
Q_CAP
Buck-boost 1 and 2 enabled
Buck-boost 1 and 2 and LDO 1 enabled
Buck-boost 1 and 2 and LDO 1 and 2 enabled
POWER SEQUENCE
Reset Time Accuracy
BUCK-BOOST REGULATOR
Input Voltage
Output Voltage Range
Quiescent Supply
Current From CAP
Output Accuracy
Power Supply Rejection
Ratio
Maximum Input Power
Maximum Input Current
Short-Circuit Current
Limit
Passive Discharge
Resistance
LDO
Quiescent Supply
Current
Quiescent supply
Current in Dropout
Maximum Output
Current
Output Voltage
I
Q_LDO
I
Q_LDO_D
I
MAX_LDO
V
OUT_LDO
LDO UVLO enabled
Switch mode, V
BB_OUT
= +1.8V
V
BB_OUT
= V
LDO_SET
– 0.1V
(Note 4)
50mV steps
50
0.5
3.65
1.1
0.4
1.7
3.5
2
µA
µA
mA
V
t
RST
V
BAT
V
OUT
Operating
Startup
50mV steps, (Note 3)
Burst mode, no switching, V
BB_OUT
= +1.8V
T
A
= +25°C
V
OUT_ACC_BB_OUT
PSRR
P
IN
I
IN
I
LIM
R
PAS_BB_OUT
T
A
= 0°C to +85°C
T
A
= -40°C to +85°C
C
BB_OUT
= 10µF
(Note 5)
V
BB_OUT
= +1.8V
V
BB_OUT
= +3.3V
Maximum programmable current setting
250
200
244
0.6
10
-1
-1.8
-3
40
-10
0.7
0.8
0.9
1
1
+1.8
+3
dB
mW
mA
A
kΩ
%
+10
2
2
4.05
%
CONDITIONS
Seal mode, all functions disabled,
T
A
= +25°C
MIN
TYP
0.01
465
4
5
5.25
5.5
MAX
0.2
UNITS
µA
kΩ
µA
µA
µA
µA
V
V
µA
I
Q_BB
www.maximintegrated.com
Maxim Integrated
│
3
MAX20310
Ultra-Low Quiescent Current PMIC with
SIMO Buck-Boost for Wearable Applications
Electrical Characteristics (continued)
(V
BAT
= +1.2V, V
BB1OUT
= +1.8V, V
BB2OUT
= +1.2V, V
L1OUT
= +1.5V, V
L2OUT
= +1.0V, I
BB1OUT
= I
BB2OUT
= I
L1OUT
= I
L2OUT
= 0A,
T
A
= -40°C to +85°C, all registers in their default state, unless otherwise noted. Typical values are at T
A
= +25°C) (Note 1) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
V
BB_OUT
=
(V
LDO_SET
+
0.5V) or higher,
I
LOAD
= 1mA
T
A
= 0°C to +85°C
T
A
= -40°C to +85°C
MIN
-3
-3.5
TYP
MAX
3
%
+3.5
100
-1
0.003
10
V
BB_OUT
= +1.2V
I
LDO_OUT
= 0mA
I
LDO_OUT
= 0mA. Switch mode.
T
J
rising
0.7
2.8
150
21
1
1
mV
%/V
%/mA
kΩ
Ω
V/µs
°C
°C
UNITS
Output Accuracy
V
OUT_ACC_LDO
Dropout Voltage
Line Regulation
Load Regulation
Passive Discharge
Resistance
Power Switch Mode
Resistance
Turn-On Time
Thermal Shutdown
Threshold
Thermal Shutdown
Hysteresis
MONITOR MULTIPLEXER
MON Impedance
Battery Voltage Buffer
Precision
DIGITAL SIGNALS
SDA, SCL, MPC Input
Logic-High
SDA, SCL, MPC Input
Logic-Low
SDA,
RST, KOUT
Output Logic-Low
MPO Output Logic-Low
SCL Clock Frequency
Bus Free Time Between
a STOP and START
Condition
V
DROP_LDO
LINEREG
LDO
LOADREG
LDO
R
PAS_LDO
R
ON_LS
t
ON_SLOPE
T
SD
T
HYS
V
BB_OUT
= V
LDO_SET
= +1.8V,
I
LOAD
= 50mA
V
BB_OUT
= (V
LDO_SET
+ 0.5V) to
+4.05V
I
LOAD
= 50µA to 50mA
R
MON
V
BAT_OFF
Sense pin voltage > +0.5V
-10
500
10
Ω
mV
V
IH
V
IL
V
OL
V
OL_MPO
f
SCL
t
BUF
I
OL
= 4mA
I
OL
= 4mA to GND
I
OL
= 4mA to BATN
(Note 5)
1.4
0.5
0.4
0.4
0.4
0
1.3
400
V
V
V
V
kHz
µs
www.maximintegrated.com
Maxim Integrated
│
4
MAX20310
Ultra-Low Quiescent Current PMIC with
SIMO Buck-Boost for Wearable Applications
Electrical Characteristics (continued)
(V
BAT
= +1.2V, V
BB1OUT
= +1.8V, V
BB2OUT
= +1.2V, V
L1OUT
= +1.5V, V
L2OUT
= +1.0V, I
BB1OUT
= I
BB2OUT
= I
L1OUT
= I
L2OUT
= 0A,
T
A
= -40°C to +85°C, all registers in their default state, unless otherwise noted. Typical values are at T
A
= +25°C) (Note 1) (Note 2)
PARAMETER
START Condition
(Repeated) Hold Time
Low Period of SCL
Clock
High Period of SCL
Clock
Setup Time for a
Repeated START
Condition
Data Hold Time
Data Setup Time
Setup Time for STOP
Condition
Note
Note
Note
Note
Note
Note
Note
Note
1:
2:
3:
4:
5:
6:
7:
8:
SYMBOL
t
HD:STA
t
LOW
t
HIGH
(Note 6)
CONDITIONS
MIN
0.6
1.3
0.6
TYP
MAX
UNITS
µs
µs
µs
µs
µs
µs
ns
µs
t
SU:STA
t
HD:DAT
t
SU:DAT
t
SU:STO
(Notes 7, 8)
(Note 7)
0.6
0
100
0.6
All devices are 100% production tested at T
A
= +25°C. Limits over the operating temperature range are guaranteed by design.
V
BAT
refers to the voltage across the battery terminals; V
BAT
= V
GND
– V
BATN
.
Output voltage must not exceed V
BB_OUT
- V
BATN
= 5.0V.
Actual value may be limited by the lower of the capability of the source (battery) or the maximum input power of the MAX20310.
Timing must be fast enough to prevent the device from entering sleep mode due to bus low for period > t
SLEEP
.
f
SCL
must meet the minimum clock low time plus the rise/fall times.
The maximum t
HD:DAT
has to be met only if the device does not stretch the low period (t
LOW
) of the SCL signal.
The device internally provides a hold time of at least 100ns for the SDA signal (referred to the V
IH_MIN
of the SCL signal) to
bridge the undefined region of the falling edge of SCL.
If the following code and connection method are used to use G2553 and 12864, where should the power supply be added? And this code has a warning Warning [Pe175]: subscript out of range, what should I ...
Key points to pay attention to in the design of electronic ballasts Designers of fluorescent lamp electronic ballasts often pay more attention to the power factor, harmonics,lamp current peak ratio an...
Regarding the problem of electricity theft, it seems important to prevent it through meter reading. I will discuss this in another thread. Personally, I think the biggest difficulty in preventing elec...
I would like to ask the experts a question. How to deal with the idle IO ports of the microcontroller? I have seen various opinions on the Internet. Some say to set it as input and connect a resistor ...
I have two power supplies, with output voltages of 24V and 15V respectively. How can I make these two power supplies power a 5 ohm load at the same time?...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
Almost everyone in a student dormitory has a bedside lamp. But if you want to read for a while after turning off the lights and don't want to disturb your roommates' sleep, you may need a reading l...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
