mSATA Flash Drive
APMxxxGM1AN-XXTX
Features:
Compliance with SATA Revision 3.1
–
SATA 6.0 Gbps interface
–
Backward compatible with SATA 1.5/3.0
Gbps interfaces
–
ATA command set
Capacity
–
4, 8, 16, 32, 64 GB
Performance*
–
Interface burst read/write:
600
MB/sec
–
Sustained read: up to 125 MB/sec
–
Sustained write: up to 110 MB/sec
Flash Management
–
Built-in hardware ECC
–
Wear leveling
–
Bad block management
–
S.M.A.R.T.
–
Power Failure Management
–
TRIM
NAND Flash Type:
SLC
MTBF:
>2,000,000 hours
Temperature Range
–
Operating:
Standard: 0°C to 70°C
Extended: -40°C to 85°C
–
Storage: -40°C to 100°C
Supply Voltage
–
3.3 V
±
5%
Power Consumption*
–
Active mode: 350 mA
–
Idle mode: 85 mA
Form Factor
–
JEDEC MO-300
–
Dimensions (50.80 x 29.85 x 4.85, unit:
㎜)
Connector
–
52-pin mSATA signal connector
RoHS Compliant
Support Device Sleep Mode (No DEVSLP Mode
as optional)
*Varies
from capacities. The values addressed here are typical and may vary depending on host system settings.
1
© 2016 Apacer Technology Inc.
Rev. 1.0
mSATA Flash Drive
APMxxxGM1AN-XXTX
Table of Contents
1. Product Description
............................................................................................ 3
1.1 Introduction .................................................................................................................................... 3
1.2 Capacity Specifications ................................................................................................................ 3
1.3 Performance ................................................................................................................................... 3
1.4 Pin Assignments ............................................................................................................................ 4
2. Software Interface
............................................................................................... 6
2.1 Command Set ................................................................................................................................. 6
2.2 S.M.A.R.T. ....................................................................................................................................... 6
3. Flash Management
.............................................................................................. 7
3.1 Error Correction/Detection ........................................................................................................... 7
3.2 Bad Block Management ................................................................................................................ 7
3.3 Wear Leveling ................................................................................................................................. 7
3.4 Power Failure Management .......................................................................................................... 7
3.5 TRIM ................................................................................................................................................ 7
3.6 Page Mapping FTL ......................................................................................................................... 7
3.7 DEVSLP (DevSleep or DEVSLP) Mode ........................................................................................ 8
3.8 Secure Erase .................................................................................................................................. 8
4. Environment Specifications..............................................................................
9
4.1 Environmental ................................................................................................................................ 9
4.2 Mean Time Between Failures (MTBF) .......................................................................................... 9
4.3 Certification and Compliance ....................................................................................................... 9
5. Electrical Characteristics
............................................................................... 10
5.1 Operating Voltage ........................................................................................................................ 10
5.2 Power Consumption .................................................................................................................... 10
6. Mechanical Specifications
.............................................................................. 11
6.1 Dimensions ................................................................................................................................... 11
7. Product Ordering Information
........................................................................ 12
7.1 Product Code Designation .......................................................................................................... 12
7.2 Valid Combinations ..................................................................................................................... 13
2
© 2016 Apacer Technology Inc.
Rev. 1.0
mSATA Flash Drive
APMxxxGM1AN-XXTX
1. Product Description
1.1 Introduction
Apacer mSATA H1 delivers all the advantages of flash disk technology with the Serial ATA 6.0 Gbps interface
and is fully compliant with the standard mSATA form factor, known as JEDEC MO-300 standard. The module is
designed to operate at optimal efficiency and reliability. Its performance can reach up to 125 MB/s read and up
to 110 MB/s write. Meanwhile, the power consumption of the mSATA module is much lower than traditional
hard drives.
1.2 Capacity Specifications
Table 1-1
Capacity Specifications
Capacity
4 GB
8 GB
16 GB
32 GB
64 GB
Total Bytes
4,011,614,208
8,012,390,400
16,013,942,784
32,017,047,552
64,023,257,088
Cylinders
7,773
15,525
16,383
16,383
16,383
Heads
16
16
16
16
16
Sectors
63
63
63
63
63
Max LBA
7,835,184
15,649,200
31,277,232
62,533,296
125,045,424
*Display of total bytes varies from file systems.
**Cylinders, heads or sectors are not applicable for these capacities. Only LBA addressing applies.
LBA count addressed in the table above indicates total user storage capacity and will remain the same throughout
the lifespan of the device. However, the total usable capacity of the SSD is most likely to be less than the total
physical capacity because a small portion of the capacity is reserved for device maintenance usages.
1.3 Performance
Performance of mSATA H1 is shown in Table 1-2.
Table 1-2
Performance Specifications
Capacity
Performance
Sustained Read (MB/s)
Sustained Write (MB/s)
4 GB
32
27
8 GB
60
50
16 GB
125
105
32 GB
120
105
64 GB
120
110
Note: Performance varies from flash configurations or host system settings.
3
© 2016 Apacer Technology Inc.
Rev. 1.0
Talking
京公网安备 11010802033920号
EEWORLD
