10 to 55 Hz at double amplitude of 1.5 mm (detection time: 10μs) (Only the NC contact of 1 Form C is 0.82mm)
10 to 55 Hz at double amplitude of 1.5 mm
Min. 1×10
6
(at 180 times/min.)
Ambient temperature: –40 to +85°C
–40 to +185°F
(Class B insulation), –40 to +105°C
–40 to +221°F
(Class F
insulation),
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
Approx. 11 g
.39 oz
Specifications
Notes: *1.This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. Wave is standard shock voltage of
±1.2×50μs
according to JEC-212-1981
*3. For the ambient temperature, please refer to Usage, transport and storage conditions in NOTES.
*Please note that some of the specifications listed above may not comply with overseas standards.
3. Expected electrical life
Condition: Resistive, at 20°C
68°F
Type
1 Form A
NO contact
1 Form C
NC contact
For the operating ambient temperature, please read the notes
16A 250V AC
Switching capacity
16A 250V AC
16A 250V AC
Number of operations
Min. 1×10
5
(ON:OFF = 1.5s:1.5s)
Min. 5×10
4
(ON:OFF = 1.5s:1.5s)
Min. 1×10
4
(ON:OFF = 1.5s:1.5s)
–2–
ASCTB395E 201809-T
LZ-N (ALZN)
REFERENCE DATA
1. Max. switching capacity (AC resistive load)
2. Coil temperature rise (Ave.)
Tested sample: ALZN1F12, 6pcs.
Contact current: 16A
Ambient temperature: Normal temperature • 85°C
185°F
• 105°C
221°F
Measured portion: inside the coil
100
50
30
20
10
5
65
Normal temperature 16A
Coil applied voltage, %V
60
Temperature rise,
°C
55
50
45
40
35
30
50
25
0
30
100
500 1,000
Contact voltage, V
20
95 100 105 110 115 120 125 130 135
Coil applied voltage, %V
0
0
85°C 16A
105°C 16A
3. Ambient temperature characteristics (Ave.)
Tested sample: ALZN1F12, 6pcs.
Contact carrying current: 0A, 16A
Measured portion: inside the coil
300
250
16A 155°C
Contact current, A
200
150
100
16A 130°C
Operate voltage
(Hot start: 16A, 100%V)
1
0.5
Operate voltage
(Cold start: Coil and contact no carrying current)
20
40
60
80
100
Ambient temperature,
°C
120
DIMENSIONS
(mm
inch)
1. 1 Form A type
The CAD data of the products with a “CAD” mark can be downloaded from our Website.
[p=35, null, left][color=#555555][font="][size=15px]Bit operations are very common in hardware programming. Often each bit of a register has a different meaning, including getting the state of the bit...
This is the first time I use this type of LCD screen. In addition to the data I/O port, it only has DISP, VSYNC, HSYNC and DE I/O ports. I would like to ask if any experts have used this type of LCD, ...
I recently ported the TCPIP protocol to LPC2292. During the test, I found that the program ran away. After looking for the cause, I found that when assigning the first data to a structure pointer poin...
[size=4]When it comes to lithium-ion batteries, we should think of several parts: [/size][size=4]battery cells, fuel gauge, battery protection board, and battery charging circuit. [/size] [size=4] [/s...
As shown in the figure:What is the function of the components in the red box in the above figure? What is the benefit of this connection? The two ends of the LED are connected to a 5V power supply...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
Button cells (also called button cells) are those batteries with equal or larger diameter and height. The current size range of alkaline button cells is specified as follows: diameter 4.8mm-11.4mm,...[Details]
1 Introduction
The function of the material transport vehicle is to lift the mixed finished materials into the finished material storage bin. In the early mixing equipment, the material transpo...[Details]
As the global leader in virtual instrument technology, NI provided customers with more than 6,000,000 virtual instrument measurement devices in 2004 alone. For 25 years, engineers have used virtual...[Details]
What is Power Monitoring Software
Power monitoring software is used in conjunction with an uninterruptible power supply (UPS) to improve its performance. When using an UPS, users can use this ...[Details]
In recent years, information technology based on microelectronics and computer technology has developed rapidly, and ultrasonic non-destructive testing instruments have also gained unpreceden...[Details]
1. Architecture and operation of electronic toll collection system
The basic principle of the electronic toll collection system is to enable a special device (on-board unit) installed on t...[Details]
As the trend towards miniaturization continues, new packaging methods and methods of interconnecting integrated circuits have been developed. Today, "system on chip" refers to a packaging method th...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
