10 to 55 Hz at double amplitude of 1.5 mm (detection time: 10μs) (Only the NC contact of 1 Form C is 0.82mm)
10 to 55 Hz at double amplitude of 1.5 mm
Min. 1×10
6
(at 180 times/min.)
Ambient temperature: –40 to +85°C
–40 to +185°F
(Class B insulation), –40 to +105°C
–40 to +221°F
(Class F
insulation),
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
Approx. 11 g
.39 oz
Specifications
Notes: *1.This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. Wave is standard shock voltage of
±1.2×50μs
according to JEC-212-1981
*3. For the ambient temperature, please refer to Usage, transport and storage conditions in NOTES.
*Please note that some of the specifications listed above may not comply with overseas standards.
3. Expected electrical life
Condition: Resistive, at 20°C
68°F
Type
1 Form A
NO contact
1 Form C
NC contact
For the operating ambient temperature, please read the notes
16A 250V AC
Switching capacity
16A 250V AC
16A 250V AC
Number of operations
Min. 1×10
5
(ON:OFF = 1.5s:1.5s)
Min. 5×10
4
(ON:OFF = 1.5s:1.5s)
Min. 1×10
4
(ON:OFF = 1.5s:1.5s)
–2–
ASCTB395E 201809-T
LZ-N (ALZN)
REFERENCE DATA
1. Max. switching capacity (AC resistive load)
2. Coil temperature rise (Ave.)
Tested sample: ALZN1F12, 6pcs.
Contact current: 16A
Ambient temperature: Normal temperature • 85°C
185°F
• 105°C
221°F
Measured portion: inside the coil
100
50
30
20
10
5
65
Normal temperature 16A
Coil applied voltage, %V
60
Temperature rise,
°C
55
50
45
40
35
30
50
25
0
30
100
500 1,000
Contact voltage, V
20
95 100 105 110 115 120 125 130 135
Coil applied voltage, %V
0
0
85°C 16A
105°C 16A
3. Ambient temperature characteristics (Ave.)
Tested sample: ALZN1F12, 6pcs.
Contact carrying current: 0A, 16A
Measured portion: inside the coil
300
250
16A 155°C
Contact current, A
200
150
100
16A 130°C
Operate voltage
(Hot start: 16A, 100%V)
1
0.5
Operate voltage
(Cold start: Coil and contact no carrying current)
20
40
60
80
100
Ambient temperature,
°C
120
DIMENSIONS
(mm
inch)
1. 1 Form A type
The CAD data of the products with a “CAD” mark can be downloaded from our Website.
Now due to some special requirements, I want to make a four-way current source with an output between 500uA and 5mA. I would like to ask you to recommend some solutions or chips or circuit principles....
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:58[/i] Adnaan Ahmad, a technology hardware analyst at Berenberg Capital Markets, a German market research firm, recently made his top t...
usqlite is a SQL database module for MicroPython built on top of the SQLite C library.The usqlite SQL interface is designed as a subset of the DB-API 2.0 specification specified in PEP 249.It is highl...
I am doing an MPPT project at school. I can't afford a 2812 board and an emulator. I plan to use a 28027. I have a 2812 textbook, but I don't know if it is universal. Please help....
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
introduction
LEDs continue to gain popularity in automotive applications, thanks to their long lifespan and the flexibility they offer for body styling and interior design. Some may be surpris...[Details]
One in five car failures are caused by batteries, a problem that will become more serious in the coming years as electric-by-wire, start/stop engine management and hybrid (electric/gas) vehicles be...[Details]
introduction
When it comes to the production of mobile phone lithium-ion batteries, the first thing that comes to mind is Japan's industrialized mechanical assembly line, NOKIO, MOTOLROLA's st...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
