tured with the highest quality materials for reliable and
repeatable performance providing a cost effective
thermal management solution. These devices are
constructed with Aluminum Nitride (AlN) or Beryllium
Oxide (BeO) and are available in standard EIA form factors.
Q-Bridge provides the designer with the ability to manage
thermal conditions by directing heat to a thermal ground
plane, heat sink or any other specific thermal point
of interest. The inherently low capacitance makes
this device virtually transparent at RF / microwave
frequencies. This device has the added benefit of offering
additional layers of protection to adjacent components
from hot spot thermal loads.
Q-Bridge provides the benefit of increased overall cir-
cuit reliability. ATC’s Q-Bridge is manufactured using
one-piece construction, providing a RoHS compliant
SMT package that is fully compatible with high speed auto-
mated pick-and-place processing. It is available in various
EIA case sizes. Custom configurations are also available.
Applications:
• GaN Power Amplifiers
• High RF Power Amplifiers
• Filters
• Synthesizers
• Industrial Computers
• Switch Mode Power Supplies
• Pin & Laser Diodes
Features:
• High Thermal Conductivity
• Low Thermal Resistance
• Low Capacitance
• Increases Circuit Reliability
• RoHS Compliant
• More efficient thermal management
Functional Applications:
• Between active device and adjacent ground planes
• Specific contact pad to case
• Contact pad to contact pad
• Direct component contact to via pad or trace
• Edges fully metalized
Termination Materials
ATC Termination Code
Y
S
Termination Materials
Silver Platinum Non-Magnetic Termination
Silver over Magnetic Termination
Note: Non-edge wrapped style in all case sizes is supplied with S termination
Edge wrapped style in case sizes 0302 through 1111 is supplied with Y termination
Edge wrapped style in case sizes 2010 through 3737 are supplied with S termination
ATC # 001-1143
Rev. H, 7/17
ATC Q-BRIDGE THERMAL CONDUCTOR
Mechanical Configurations
t
L
W
L
t
W
T
T
Edge Wrapped
No Wrap
Typical Characteristics
Case
Size
Length (L)
Width (W)
Thickness
(T)
Terminal
(t)
Thermal
Thermal
Resistance (°C/W) Conductivity (mW/°C)
AlN
BeO
AlN
BeO
Available
Configurations
Style
Termination
W
Y
.030 ±.002
.020 ±.002
20
10
0302
19
12
53
81
(.77 ±.051)
(0.51 ±.051) (0.51 ±.05)
(0.25)
E
S
W
Y
.040 ±.002
.020 ±.002
20
10
0402
25
16
40
61
(1.02 ±.051) (0.51 ±.051) (0.51 ±.05)
(0.25)
E
S
W
Y
.050 ±.002
.050 ±.002
25
15
0505
10
7
100
153
(1.27 ± .051) (1.27 ±.051) (0.64 ±.05)
(0.38)
E
S
W
Y
.060 ±.002
.030 ±.002
25
15
0603
20
13
50
76
(1.52 ±.051)
(.76 ±.051)
(0.64 ±.05)
(0.38)
E
S
W
Y
.080 ±.002
.050 ±.002
40
20
0805
10
7
100
153
(2.03 ±.051) (1.27 ±.051) (1.02 ±.05)
(0.51)
E
S
W
Y
.100 ±.002
.050 ±.002
40
20
1005
13
8
77
122
(2.54 ±.051) (1.27 ±.051) (1.02 ±.05)
(0.51)
E
S
W
Y
.100 ±.002
.200 ±.002
40
20
1020
3
2
320
508
(2.54 ±.051) (5.08 ±.051) (1.02 ±.05)
(0.51)
E
S
W
Y
.110 ±.002
.110 ±.002
40
20
4
153
240
1111
7
(2.79 ±.051) (2.79 ±.051) (1.02 ±.05)
(0.51)
E
S
W
S
.195 ±.010
.095 ±.010
60
30
2010
10
6
100
159
(4.95 ±.254) (2.41 ±.254) (1.52 ±.05)
(0.77)
E
S
W
S
.240 ±.010
.250 ±.010
60
40
2525
4
3
240
380
(6.10 ±.254) (6.35 ±.254) (1.52 ±.05)
(1.02)
E
S
W
S
.370 ±.010
.245 ±.010
60
50
3725
6
4
160
254
(9.40 ±.254) (6.22 ±.254) (1.52 ±.05)
(1.27)
E
S
W
S
.365 ±.010
.375 ±.010
60
50
4
3
240
380
3737
(9.27 ±.254) (9.53 ±.254) (1.52 ±.05)
(1.27)
E
S
inches (mm)
Note: Thermal conductivity is normalized to chip size. All values are approximate. Consult factory for extended thermal conductivity options.
ATC Q-BRIDGE THERMAL CONDUCTOR
ATC Part Number Code
QB
Q-Bridge
Case Size
Substrate
A = AlN; B = BeO
Thickness (mils)
0603
A
25
W
Y
T
Packaging
T = Tape and Reel, std.
1000 pc., 7” Reel
500 pc., 7” Reel
C = ATC Matrix Tray
Termination Code
Y = Silver Platinum
Non-Magnetic Termination
S = Silver over Magnetic Termination
Style: W = Edge Wrap; E = No Wrap
The above part number refers to a Q-Bridge, (EIA case size 0603), Aluminum Nitride (AlN) substrate, Thickness 25 mils.,
Style W, Y Termination (Silver Platinum Non-Magnetic Termination), with Tape and Reel Packaging.
ATC accepts orders for our parts using designations
with
or
without
the “ATC” prefix. Both
methods of defining the part number are equivalent, i.e., part numbers referenced with the
“ATC” prefix are interchangeable to parts referenced without the “ATC” prefix. Customers are
free to use either in specifying or procuring parts from American Technical Ceramics.
For additional information and catalogs contact your ATC
representative or call direct at +1-631-622-4700.
Consult factory for additional performance data.
Sales of ATC products are subject to the terms and conditions contained in American Technical Ceramics Corp. Terms and Conditions of Sale (ATC document #001-992). Copies of these terms and
conditions will be provided upon request. They may also be viewed on ATC’s website at www.atceramics.com/productfinder/default.asp. Click on the link for Terms and Conditions of Sale.
ATC has made every effort to have this information as accurate as possible. However, no responsibility is assumed by ATC for its use, nor for any infringements of rights of third parties which may
result from its use. ATC reserves the right to revise the content or modify its product line without prior notice.
[p=30, null, left][color=#252525][font=宋体,]The economic term "inflation" may be the most appropriate to describe the battery life of mobile phones. A few years ago, even flagship models such as Samsun...
Under EVC, IImage can decode PNG, but why is the transparent part white? Below is the code. How can I solve this problem? Is there any other way to solve the display problem of PNG under EVC? hr = Fin...
[i=s] This post was last edited by wgsxsm on 2015-6-12 10:39 [/i]Note: KEY 1,3 are connected together by hardware, please ignore the NC component. As shown in the figure above, when the KEY is pressed...
In any switching power supply design, the physical design of the PCB board is the last link. If the design method is not appropriate, the PCB may radiate too much electromagnetic interference, causing...
Reposted from: Diandiandi Moderator [url=http://www.pic16.com/bbs/dispbbs.asp?boardid=8&replyid=172309&id=46618&page=1&skin=0&Star=1]http://www.pic16.com/bbs/dispbbs.asp?boardid=8&replyid=172309&id=46...
Has anyone used cycloneⅣ's lvds macro? I'm having a few problems, for example, no matter how wide tx_in is, the input is always 8 bits, etc. It's amazing. I need help, I've been trying to figure this ...
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
I've been studying dot matrix recently. It looks simple, but it takes a while to master it completely! The 8*8 dot matrix hardware circuit I'm making now is like this. The row is driven by 74HC138 + t...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
/201907113877442_pdf/pg_0001.png)
Power technology
京公网安备 11010802033920号
EEWORLD/201907113877442_pdf/1.png)
/201907113877442_pdf/2.png)
/201907113877442_pdf/3.png)
/201907113877442_pdf/4.png)
/201907113877442_pdf/pg_0002.png)
/201907113877442_pdf/pg_0003.png)
/201907113877442_pdf/pg_0004.png)
