TVS diodes SMF350A/SMF350CA, SOD-123 package, peak pulse power 200W, are used in overvoltage protection of sensitive electronic parts, covering automotive electronics, consumer electronics, industrial equipment, household appliances, communication equipment and other fields.
TVS diodes SMF350A/SMF350CA, SOD-123 package, peak pulse power 200W, are used in overvoltage protection of sensitive electronic parts, covering automotive electronics, consumer electronics, industrial equipment, household appliances, communication equipment and other fields.
I am planning now,,, basically considering Beijing, Chengdu, Chongqing, Hunan,,, I am a Shanghai native,,,,,,,,, I have a house in Shanghai,,,,,,,,,...
We have a WinCE platform with Hive registry. Customers use the installation package to install software on the platform. During the installation process, the registry will be written, the relevant fil...
I have embedded LINUX and use a four-wire resistive touch screen. Now I have a problem. When I use the test program to read the value, the data of a certain area in the upper left corner of the touch ...
When using standby mode, the current is: 4uA (there are other backup clocks)When using stop mode (lower power), the current is: 118uA (there are other backup clocks)All the above modes use RTC.Accordi...
[i=s]This post was last edited by pbabca on 2015-5-7 16:59[/i] The program is to output a clock signal at CLKin, but the simulation found that the signal is all red lines. Assigning initial values, in...
Live broadcast time:
May 19 (Tuesday) 14:00-16:10Live broadcast topic:
Key points to note in new energy vehicle power designContents:
New energy vehicles have undoubtedly become the hottest technical ...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
0 Introduction
Wireless Sensor Network (WSN) monitors the target by deploying a large number of sensor nodes in the target area. WSN realizes the positioning and tracking of the target, determi...[Details]