[color=rgb(51, 51, 51)] In the process of developing new switching power adapter products, in order to ensure that the adapter can adapt to the operating requirements of different environments during ...
[media=swf,700,475]http://www.tudou.com/v/P_1pSnNazeY/&rpid=106547959&resourceId=106547959_04_05_99/v.swf[/media] [[i] This post was last edited by qinkaiabc on 2013-3-18 14:08[/i]]...
Bidirectional SPWM inverter rectifier battery charging and discharging maintenance deviceLead-acid batteries are one of the most widely used energy storage components, such as in post and telecommunic...
Dear experts, I would like to ask you a question. I am using DM642 to transplant MPEG-4 algorithm.After reading the MPEG-2LOOPBACK program in the experiment package, there are many things I don't unde...
I used TO to generate 38k infrared square wave, and used T1 to delay, so that I could generate square wave in segments, and then use the integrated connector to receive it. I found that no matter what...
The simplified schematic diagram of the single-ended flyback switching power supply, the input voltage is 120-150VAC, as shown in the figure
During the debugging process, if you want to observe the se...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
VP2188 is a color STN LCD module produced by Jingdian Pengyuan. This module is a dot matrix transmissive color STN display screen with a color scale of 65 k colors and white LED backlight. Its core...[Details]
OC faults may be the most frequent and the most frequent of all faults in the inverter. They alarm during the startup process, during the shutdown process, during operation, and even when powered o...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
Preface
In recent years, white light LEDs have gradually replaced incandescent bulbs and fluorescent lamps because they have unparalleled advantages over traditional light sources in terms...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
