EEWORLDEEWORLDEEWORLD

Part Number

Search

3186BE222M200MRS1

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 200V, 20% +Tol, 20% -Tol, 2200uF,
CategoryPassive components    capacitor   
File Size189KB,8 Pages
ManufacturerCDE [ CORNELL DUBILIER ELECTRONICS ]
Environmental Compliance
Download Datasheet Parametric View All

3186BE222M200MRS1 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 200V, 20% +Tol, 20% -Tol, 2200uF,

3186BE222M200MRS1 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid843985079
package instruction,
Reach Compliance Codeunknown
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.98
capacitance2200 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter35.41 mm
dielectric materialsALUMINUM
ESR52 mΩ
length105.61 mm
negative tolerance20%
Number of terminals2
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Package formScrew Ends
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)200 V
ripple current4600 mA
series3186
Terminal pitch12.7 mm
click here to see hardware and mounting options
Type 3186 85 °C Aluminum Electrolytic, Screw Terminal
Best Value 85 °C High Capacitance Screw Terminal Type
While Type 3186’s standard encasement is by compression with the
capacitor element captured on an aluminum peg in the can bottom
and a phenolic peg in the top, rilled construction is available.  With
rilled construction the element is secured by rills, spoon shaped
dimples in the side of the can.  Rilled construction offers the
industry’s highest vibration and shock withstanding and excellent
heat transfer.  Besides increasing ripple current handling, the rilled
construction extends the great value of the Type 3186 into military
and transportation applications that require rugged mechanical
capability.
Highlights
Specifications
Temperature Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Ripple Current Multipliers
- Rilled cans withstand high shock and vibration
- High ripple current capability
- High capacitance per can
–40 ºC to +85 ºC
16 Vdc to 500 Vdc
220 uF to 1.0 F
–10% +75% ≤ 160 Vdc
–10% +50% ≥ 200 Vdc
≤6√CV µA (6 mA max.) at 5 minutes
Ambient Temperature
45 °C
2.24
Frequency
60 Hz 120 Hz
16 – 100 V
0.90
1.00
1.00
200 – 500 V
0.90
300 Hz
1.15
1.25
1000 Hz
1.25
1.40
≥10
kHz
1.30
1.50
55 °C
2.00
65 °C
1.73
75 °C
1.41
85 °C
1.00
Low Temperature Characteristics
Impedance ratio: Z
–20 ⁰C
∕ Z
+25 ⁰C
≤ 8 (16–50 Vdc)
≤ 4 (63–100 Vdc)
≤ 3 (150–500 Vdc)
1,500 h @ full load at 85 °C
∆Capacitance ±10%
ESR 200% of limit
DCL 100% of limit
500 h @ 85 °C
∆Capacitance ±10%
ESR 175% of limit
DCL 100% of limit
10 to 500 Hz, 0.75 mm or 10 g* if less,
3 directions, 2 h ea
Δ Capacitance: ±5%
no visible damage or leakage
*15 g if rilled construction
RoHS Compliant
Endurance Life Test
Shelf Life Test
Vibration
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
I2C using the BBB
This article will first explain the basic method of using I2C in BBB, then use the driver that comes with BBB to read the air pressure value from the pressure sensor chip BMP085, and finally give how ...
wytalfred DSP and ARM Processors
I need help, how do I flash the firmware of Jlink?
I need help from the experts in the forum. A lot of Jlinks are broken here. It seems that the firmware is basically lost. I have tried many methods mentioned on the Internet to flash the firmware, whi...
ylk330 stm32/stm8
ReadFile failed
I encountered the following problems when using multithreading to open files in EVC: 1. When using CreateFile to open a file on the hard disk, sometimes the opening fails and GetLastError returns 2, i...
gshlsh Embedded System
Heartbeat measurement circuit based on infrared
This is a heartbeat waveform measurement circuit that uses a pair of infrared transmitting tubes + receiving tubes. It can measure the heartbeat waveform of fingers, earlobes, etc. Its principle is ro...
falderdz stm32/stm8
LM3S8962 JTAG interface pull-up problem
I am currently developing a product based on LM3S8962 and have come across a problem: Do the five JTAG signal lines TRST, TCK, TMS, TDI, and TDO need to be pulled up?There is no pull-up on the LM3S896...
sphinz Microcontroller MCU
TCP&UDP usage steps and process
TCP&UDP usage steps and process...
tonytong MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 322  1639  12  1922  994  7  33  1  39  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号