EEWORLDEEWORLDEEWORLD

Part Number

Search

M80-4T12042F2-10-321-07-321

Description
Board Connector, Female, Straight, Solder Terminal, Locking, Black Insulator, Plug
CategoryThe connector    The connector   
File Size1MB,6 Pages
ManufacturerHarwin
Websitehttp://www.harwin.com/
Download Datasheet Parametric View All

M80-4T12042F2-10-321-07-321 Overview

Board Connector, Female, Straight, Solder Terminal, Locking, Black Insulator, Plug

M80-4T12042F2-10-321-07-321 Parametric

Parameter NameAttribute value
MakerHarwin
Reach Compliance Codecompliant
Is SamacsysN
body width0.219 inch
subject depth0.205 inch
body length3.858 inch
Body/casing typePLUG
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialBERYLLIUM COPPER
Contact resistance25 mΩ
Contact styleRND PIN-SKT
Durability500 Cycles
Insulation resistance100000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYPHENYLENE SULPHIDE
Manufacturer's serial numberM80
Mixed contactsYES
Installation option 1LOCKING
Installation option 2JACKSCREW
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Plating thickness12u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.118 inch
Termination typeSOLDER
Base Number Matches1
How to distinguish between RAM and Flash when mapping off-chip memory
If VC5402 has external RAM and ROM memory, and the capacity is 128k×16bit, their physical addresses are in the range of 0x00000~0x1FFFF. When using the cmd file to map memory, use MEMORY to map a cert...
snowie Analogue and Mixed Signal
Can bq34z100 use a 1 milliohm sampling resistor?
[i=s]This post was last edited by qwqwqw2088 on 2020-11-2 16:50[/i]What is the minimum sampling resistor supported by bq34z100? Can 1 milliohm be used?The design current is below 5A, 0.125mV / 5A = 25...
qwqwqw2088 Analogue and Mixed Signal
CCS is really useful. DEBUG!!!
Here is an example for everyone. The debug interface in the book.Viewing variables automatically adds variables in your program. This variable cannot be seen during debug operation. It can only be see...
an736007364 Microcontroller MCU
Let’s learn about BCD technology for power management: BCD process overview
[b]1 Introduction[/b] BCD is a monolithic integrated process technology. First developed by STMicroelectronics (ST) in 1986, this technology can produce bipolar, CMOS and DMOS devices on the same chip...
雪山飞狐 Power technology
Jlink V8 firmware flash
I followed the online tutorial and failed to refresh. I used win7 64 bit. The jlink driver was installed in the device manager and it was shown as installed on port com5. Then I used sam-ba2.9 to refr...
大发明家 Microchip MCU
How to set a bit variable in STM32?
In keil51, just use bit plus variable name! ! What about STM32?...
wang5294 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 686  2464  355  1372  2698  14  50  8  28  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号