are constructed from four 512K x 8 SRAMs in plastic sur-
face-mount packages on an epoxy laminate board with pins.
On-board decoding selects one of the SRAMs from the
high-order address lines, keeping the remaining devices in
standby mode for minimum power consumption.
An active LOW write enable signal (WE) controls the writ-
ing/reading operation of the memory. When MS and WE inputs
are both LOW, data on the eight data input/output pins is writ-
ten into the memory location specified on the address pins.
Reading the device is accomplished by selecting the device
and enabling the outputs MS and OE active LOW while WE
remains inactive or HIGH. Under these conditions, the content
of the location addressed by the information on the address
pins is present on the eight data input/output pins.
The input/output pins remain in a high-impedance state unless
the module is selected, outputs are enabled, and write enable
(WE) is HIGH.
Functional Description
The CYM1481A is a high-performance 16-megabit static RAM
module organized as 2048K words by 8 bits. These modules
Logic Block Diagram
A
0
–A
18
19
Pin Configuration
SIP
A
19
V
CC
WE
I/O
2
I/O
3
I/O
0
A
1
A
2
A
3
A
4
GND
I/O
5
A
10
A
11
A
5
A
13
A
14
A
20
MS
A
15
A
16
A
12
A
18
A
6
I/O
1
GND
A
0
A
7
A
8
A
9
I/O
7
I/O
4
I/O
6
A
17
I/O
0
–I/O
7
V
CC
OE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Top View
512K x 8
SRAM
OE
WE
A
19
–A
20
2
1 of 4
DECODER
512K x 8
SRAM
MS
512K x 8
SRAM
512K x 8
SRAM
8
1481-1
/
Selection Guide
CYM1481A
Maximum Access Time (ns)
Maximum Operating Current (mA)
Maximum Standby Current (mA)
70
110
64
85
110
64
100
110
64
120
110
64
Cypress Semiconductor Corporation
•
3901 North First Street
•
San Jose
• CA 95134 • 408-943-2600
October 1990 - Revised April 16, 2001
CYM1481A
Maximum Ratings
(Above which the useful life may be impaired.)
Storage Temperature –55°C to +125°C
Ambient Temperature with
Power Applied0°C to +70°C
Supply Voltage to Ground Potential–0.3V to +7.0V
DC Voltage Applied to Outputs
in High Z State–0.3V to +7.0V
Range
Commercial
DC Input Voltage–0.3V to +7.0V
Output Current into Outputs (LOW)20 mA
Operating Range
Ambient
Temperature
0°C to +70°C
V
CC
5V
±
10%
Electrical Characteristics
Over the Operating Range
1481A
Parameter
V
OH
V
OL
V
IH
V
IL
I
IX
I
OZ
I
CC
I
SB1
I
SB2
Description
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input Load Current
Output Leakage Current
Automatic MS
Power-Down Current
Automatic MS
Power-Down Current
GND < V
I
< V
CC
GND < V
O
< V
CC
, Output Disabled
Max. V
CC
, MS > V
IH
,
Min. Duty Cycle = 100%
Max. V
CC
, MS > V
CC
– 0.2V,
V
IN
> V
CC
– 0.2V, or V
IN
<
0.2V
Standard
L Version
–100, –120
L Version
–85
Test Conditions
V
CC
= Min., I
OH
= –1.0 mA
V
CC
= Min., I
OL
= 2.0 mA
2.2
–0.3
–20
–20
Min.
2.4
0.4
V
CC
+ 0.3
0.8
+20
+20
110
64
32
500
1600
Max.
Unit
V
V
V
V
µA
µA
mA
mA
mA
µA
µA
V
CC
Operating Supply Current V
CC
= Max., MS < V
IL
, I
OUT
= 0 mA
Capacitance
[1]
Parameter
C
INA
C
INB
C
OUT
Description
Input Capacitance (A
0–16
, OE, WE)
Input Capacitance (A
17–20
, MS)
Output Capacitance
Test Conditions
T
A
= 25°C, f = 1 MHz,
V
CC
= 5.0V
CYM1481AM
ax.
125
25
165
Unit
pF
pF
pF
Note:
1. Tested on a sample basis.
2
CYM1481A
AC Test Loads and Waveforms
R1 2530
Ω
5V
OUTPUT
100 pF
INCLUDING
JIG AND
SCOPE
R2
2830Ω
5V
OUTPUT
5 pF
INCLUDING
JIG AND
SCOPE
R2
2830Ω
R1 2530Ω
3.0V
90%
GND
< 10 ns
10%
90%
10%
< 10 ns
ALL INPUT PULSES
(a)
Equivalent to:
OUTPUT
1481-2
(b)
1481-3
1481-4
THÉVENIN EQUIVALENT
1340Ω
2.64V
Switching Characteristics
Over the Operating Range
[2]
1481A-70
Parameter
READ CYCLE
t
RC
t
AA
t
OHA
t
AMS
t
DOE
t
LZOE
t
HZOE
t
LZMS
t
HZMS
t
WC
t
SMS
t
AW
t
HA
t
SA
t
PWE
t
SD
t
HD
t
HZWE
t
LZWE
Read Cycle Time
Address to Data Valid
Data Hold from Address Change
MS LOW to Data Valid
OE LOW to Data Valid
OE LOW to Low Z
OE HIGH to High Z
[3]
MS LOW to Low Z
[4]
MS HIGH to High Z
[3, 4]
Write Cycle Time
MS LOW to Write End
Address Set-Up to Write End
Address Hold from Write End
Address Set-Up to Write Start
WE Pulse Width
Data Set-Up to Write End
Data Hold from Write End
WE LOW to High Z
[3]
WE HIGH to Low Z
5
70
65
65
5
0
65
30
0
30
5
5
30
85
75
75
7
5
65
35
5
30
5
5
30
10
30
100
90
90
7
5
75
40
5
35
5
5
70
40
5
30
10
35
120
100
100
7
5
85
45
5
40
70
70
10
85
45
5
35
10
45
85
85
10
100
50
5
45
100
100
10
120
60
120
120
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Description
Min.
Max.
1481A–85
Min.
Max.
1481A–100
Min.
Max.
1481A–120
Min.
Max.
Unit
WRITE CYCLE
[5]
Notes:
2. Test conditions assume signal transition time of 10
µs
or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, output loading of 1 TTL load, and
100-pF load capacitance.
3. t
HZOE
, t
HZMS
, and t
HZWE
are specified with C
L
= 5 pF as in part (b) of AC Test Loads and Waveforms. Transition is measured
±500
mV from steady-state voltage.
4. At any given temperature and voltage condition, t
HZMS
is less than t
LZMS
for any given device. These parameters are guaranteed and not 100% tested.
5. The internal write time of the memory is defined by the overlap of MS LOW and WE LOW. Both signals must be LOW to initiate a write and either signal can
terminate a write by going HIGH. The data input set-up and hold timing should be referenced to the rising edge of the signal that terminates the write.
3
CYM1481A
Data Retention Characteristics
(L Version Only)
1481A-70
Parameter
V
DR
I
CCDR
t
CDR[6]
t
R
Description
V
CC
for Retention Data
Data Retention Current V
DR
= 3.0V,
MS > V
CC
– 0.2V,
Chip Deselect to Data
V
IN
> V
CC
– 0.2V or V
IN
Retention Time
< 0.2V
Operation Recovery
Time
Test Conditions
Min.
2
800
0
5
0
5
Max.
1481A–85
Min.
2
800
0
5
Max.
1481A–100
148A1–120
Min.
2
250
Max.
Unit
V
µA
ns
ns
Data Retention Waveform
DATA RETENTION MODE
V
CC
4.5V
t
CDR
V
DR
CS
V
IH
V
IH
1481-6
V
DR
> 2V
4.5V
t
R
Switching Waveforms
Read Cycle No. 1
[7, 8]
t
RC
ADDRESS
t
AA
t
OHA
DATAOUT
PREVIOUS DATA VALID
DATA VALID
1481-7
Notes:
6. Guaranteed, not tested.
7. Device is continuously selected. OE, MS = V
IL
.
8. Address valid prior to or coincident with MS transition LOW.
[i=s]This post was last edited by paulhyde on 2014-9-15 03:56[/i] After two months of hard work on the national competition, it finally came to an end yesterday. I saw how difficult the national compe...
Any technology, as long as it is advanced enough, cannot be distinguished from magic.--Arthur C. Clarke
Countless machines have been invented to solve a variety of problems. Computers range from those...
The board that just arrived today: STM32F769IWhile everyone is busy, I will unpack it and give you a simple unboxing. If you like it, you can apply for a free evaluation in the link below{:1_102:}The ...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
