EEWORLDEEWORLDEEWORLD

Part Number

Search

PCA9550DP

Description
2-bit I2C LED driver with programmable blink rates
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size126KB,26 Pages
ManufacturerNXP
Websitehttps://www.nxp.com
Environmental Compliance
Download Datasheet Parametric Compare View All

PCA9550DP Overview

2-bit I2C LED driver with programmable blink rates

PCA9550DP Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerNXP
Parts packaging codeSOIC
package instructionTSSOP, TSSOP8,.19
Contacts8
Reach Compliance Codecompliant
ECCN codeEAR99
data entry modeSERIAL
Interface integrated circuit typeLED DISPLAY DRIVER
JESD-30 codeS-PDSO-G8
JESD-609 codee4
length3 mm
Humidity sensitivity level1
Multiplex display functionNO
Number of functions1
Number of segments2
Number of terminals8
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Package body materialPLASTIC/EPOXY
encapsulated codeTSSOP
Encapsulate equivalent codeTSSOP8,.19
Package shapeSQUARE
Package formSMALL OUTLINE, THIN PROFILE, SHRINK PITCH
Peak Reflow Temperature (Celsius)260
power supply2.5/5 V
Certification statusNot Qualified
Maximum seat height1.1 mm
Maximum supply voltage5.5 V
Minimum supply voltage2.3 V
Nominal supply voltage3.3 V
surface mountYES
Temperature levelINDUSTRIAL
Terminal surfaceNickel/Palladium/Gold (Ni/Pd/Au)
Terminal formGULL WING
Terminal pitch0.65 mm
Terminal locationDUAL
Maximum time at peak reflow temperature30
width3 mm
minfmax0.4 MHz
PCA9550
2-bit I
2
C-bus LED driver with programmable blink rates
Rev. 05 — 13 October 2008
Product data sheet
1. General description
The PCA9550 LED blinker blinks LEDs in I
2
C-bus and SMBus applications where it is
necessary to limit bus traffic or free up the I
2
C master's (MCU, MPU, DSP, chip set, etc.)
timer. The uniqueness of this device is the internal oscillator with two programmable blink
rates. To blink LEDs using normal I/O expanders like the PCF8574 or PCA9554, the bus
master must send repeated commands to turn the LED on and off. This greatly increases
the amount of traffic on the I
2
C-bus and uses up one of the master's timers. The PCA9550
LED blinker instead requires only the initial set-up command to program BLINK RATE 1
and BLINK RATE 2 (i.e., the frequency and duty cycle). From then on, only one command
from the bus master is required to turn each individual open-drain output ON, OFF, or to
cycle at BLINK RATE 1 or BLINK RATE 2. Maximum output sink current is 25 mA per bit
and 50 mA per package.
Any bits not used for controlling the LEDs can be used for General Purpose parallel
Input/Output (GPIO) expansion.
The active LOW hardware reset pin (RESET) and Power-On Reset (POR) initializes the
registers to their default state, all zeroes, causing the bits to be set HIGH (LED off).
One hardware address pin on the PCA9550 allows two devices to operate on the same
bus.
2. Features
I
2 LED drivers (on, off, flashing at a programmable rate)
I
2 selectable, fully programmable blink rates (frequency and duty cycle) between
0.172 Hz and 44 Hz (5.82 seconds and 0.023 second)
I
Input/output not used as LED drivers can be used as regular GPIOs
I
Internal oscillator requires no external components
I
I
2
C-bus interface logic compatible with SMBus
I
Internal power-on reset
I
Noise filter on SCL/SDA inputs
I
Active LOW reset input
I
2 open-drain outputs directly drive LEDs to 25 mA
I
Controlled edge rates to minimize ground bounce
I
No glitch on power-up
I
Supports hot insertion
I
Low standby current
I
Operating power supply voltage range of 2.3 V to 5.5 V
I
0 kHz to 400 kHz clock frequency

PCA9550DP Related Products

PCA9550DP PCA9550 PCA9550TK
Description 2-bit I2C LED driver with programmable blink rates 2-bit I2C LED driver with programmable blink rates 2-bit I2C LED driver with programmable blink rates
Automobile engine upgrade product, an electronic accelerator with obvious effect
An electronic accelerator is not an electronic throttle accelerator for cars. This electronic accelerator is a new product and new technology. Traditional cars can solve the following problems by conn...
aszx58 Automotive Electronics
Yuan Fang, what do you think of this circuit? (5)
[font=宋体]Yuan Fang: Sir, last time you pointed out the zero-pole distribution in the case, and the various elements of the case have been revealed, but Yuan Fang still cannot sort out the whole case f...
zjd01 Analogue and Mixed Signal
Can TVS tubes completely replace ESD static diodes?
Can TVS tubes completely replace ESD electrostatic diodes? What is the difference between the two?...
unsemi 51mcu
How to use the dual ADC fast alternating mode in STM32?
I've been learning how to use the ADC of STM32 recently. The single ADC has been debugged successfully, and the LCD can display the actual waveform.I saw that there is a dual ADC fast alternating mode...
ubrownie stm32/stm8
Problem with simulation
I think it's a font problem, please help! The program and simulation (protues) are in the attachment....
结束是开始 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 9  34  1892  175  1  1  39  4  28  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号