EEWORLDEEWORLDEEWORLD

Part Number

Search

LTC1957-2

Description
Single/Dual Band RF Power Controllers with 40dB Dynamic Range
File Size202KB,16 Pages
ManufacturerLinear ( ADI )
Websitehttp://www.analog.com/cn/index.html
Download Datasheet Compare View All

LTC1957-2 Overview

Single/Dual Band RF Power Controllers with 40dB Dynamic Range

LTC1957-1/LTC1957-2
Single/Dual Band RF Power
Controllers with 40dB Dynamic Range
FEATURES
s
s
DESCRIPTIO
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Dual Band RF Power Amplifier Control (LTC1957-2)
Internal Schottky Diode Detector with Improved
Dynamic Range vs the LTC1757A
Wide Input Frequency Range: 850MHz to 2GHz
Autozero Loop Cancels Offset Errors and
Temperature Dependent Offsets
Wide V
IN
Range: 2.7V to 6V
Allows Direct Connection to Battery
RF Output Power Set by External DAC
Fast Acquire After Transmit Enable
Internal Frequency Compensation
Rail-to-Rail Power Control Outputs
Power Control Signal Overvoltage Protection
Low Operating Current: 1mA
Very Low Shutdown Current: < 1µA
Available in a 8-Pin MSOP Package (LTC1957-1)
and 10-Pin MSOP (LTC1957-2)
Pin Compatible with the LTC1757A-X
Improved Start Voltage Accuracy and Range
Improved PCTL Input Filtering
The LTC
®
1957-2 is a dual band RF power controller for
power amplifiers operating in the 850MHz to 2GHz range.
The input voltage range is optimized for operation from
a single lithium-ion cell or 3× NiMH. Several functions
required for RF power control and protection are inte-
grated in one small 10-pin MSOP package, thereby
minimizing PCB area.
The LTC1957-1 is a single output RF power controller
that is identical in performance to the LTC1957-2 except
that one output (V
PCA
) is provided. The LTC1957-1 can
be used to drive a single RF or dual channel module with
integral multiplexer. This part is available in an 8-pin
MSOP package.
RF power is controlled by driving the RF amplifier power
control pins and sensing the resultant RF output power
via a directional coupler. The RF sense voltage is peak
detected using an on-chip Schottky diode. This detected
voltage is compared to the DAC voltage at the PCTL pin
to control the output power. The RF power amplifier is
protected against high supply current and high power
control pin voltages.
Internal and external offsets are cancelled over tempera-
ture by an autozero control loop, allowing accurate low
power programming. The shutdown feature disables the
part and reduces the supply current to < 1µA.
, LTC and LT are registered trademarks of Linear Technology Corporation.
APPLICATIO S
s
s
s
s
Single and Dual Band GSM/GPRS Cellular Telephones
PCS Devices
Wireless Data Modems
U.S. TDMA Cellular Phones
TYPICAL APPLICATIO
68Ω
V
IN
33pF
Li-Ion
SHDN
BSEL
LTC1957-2 Dual Band Cellular Telephone Transmitter
LTC1957-2
1
2
3
4
5
V
IN
RF
SHDN
BSEL
GND
V
CC
V
PCA
V
PCB
TXEN
PCTL
10
9
8
7
6
900MHz
TXEN
RF PA
DIRECTIONAL
COUPLER
DIPLEXER
DAC
1.8GHz /1.9GHz
RF PA
U
50Ω
1957 TA01
U
U
1

LTC1957-2 Related Products

LTC1957-2 LTC1957-1 LTC1957-1EMS8 LTC1957-2EMS
Description Single/Dual Band RF Power Controllers with 40dB Dynamic Range Single/Dual Band RF Power Controllers with 40dB Dynamic Range Single/Dual Band RF Power Controllers with 40dB Dynamic Range Single/Dual Band RF Power Controllers with 40dB Dynamic Range
Investigate your needs for real-time operating systems
There are many kinds of embedded operating systems nowadays, but the most popular ones in China are Linux and WinCE. I posted this post to find out how much you need real-time operating systems in you...
bluehacker Embedded System
ESP32-C3 RISC-V microcontroller information leak
Six years on from the introduction of the Espressif ESP8266, we might be led to believe that the focus has shifted to the newer dual-core ESP32. However, there is a twist in the form of the newly anno...
dcexpert MicroPython Open Source section
Modelsim post-simulation, SDF file loading failed
Question: The standard delay file generated by XILINX, after simulation with MODELSIM, the standard delay file SDF file failed to load, the error result: # Loading C:/Modeltech6.2b/xilinx_lib/simprim_...
eeleader-mcu FPGA/CPLD
Has anyone used BQ2000T?
I built the board according to the schematic diagram recommended in the data sheet, but why is it that when I charge it to the end, the red and green lights flash alternately? ?...
wzjhuohua Analogue and Mixed Signal
Let's talk about the 51 microcontroller model and development environment you use
This question originated from a sentence in the graduation thesis.I would like to do a small survey now. Due to my lack of consideration and lack of understanding of the forum's voting posts, I have m...
辛昕 51mcu
Five steps to fully embrace virtualization
In the current economic climate, many companies are cutting IT projects that don't deliver a strong ROI within 12 months. But virtualization projects are one of the IT projects that CIOs almost univer...
xyh_521 Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1011  2596  1840  794  2684  21  53  38  16  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号